REMOTE ADMINISTRATION AND MAINTENANCE PROCEDURES SECTION 100-816-600

MARCH 1993

acters represent a program group or a particular program, i.e., ALL, 03, 04, 10, 39, etc. For a printout example, see Figure 6.

NOTE:

Programs are output only in the groups indi- cated. To print out or review a program not included above, use Program Mode proce- dures.

9.04Speed Dialing Dump: While in the dump mode (see Paragraph 7), enter “REP” and two or three characters and press CR. The characters represent the speed dialing codes for either an individual station, A L L (all stations and system data) S Y S (system data only).

9.05LCD Messages Dump: While in the dump mode (see Paragraph 7), enter “MSG” and two or three characters and press CR. The characters represent stored messages for either an individual station, A L L (all stations and system data) or S Y S (system data only). For a printout example, see Figure 7.

9.06Tables provide a quick reference to the step- by-step procedures to output the appropriate data.

10 TEST MODE

10.00 General

10.01The remote test mode (see paragraph 7) can be used to test STRATA DK8 or DK16 stations

 

 

 

 

 

 

 

 

 

 

CO LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

NUMBERS

 

1:SELECT(LED ON)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

1

 

 

 

 

81

00

 

 

 

11111111

 

 

 

 

 

 

 

 

 

 

 

81

01

 

 

 

00000000

 

 

 

 

81

02

 

 

 

00000000

 

 

 

 

81

03

 

 

 

00000000

 

 

 

 

81

04

 

 

 

00000000

 

 

 

 

81

05

 

 

 

00000000

 

 

 

 

81

06

 

 

 

00000000

 

 

 

 

 

 

 

 

 

 

 

CO LINE 08

 

 

 

 

 

 

CO LINE 01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STATION PORT NUMBER

 

 

 

 

 

 

 

 

 

 

PROGRAM NUMBER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and CO line circuits from an off-site location.

10.02This testing function is accomplished by accessing stations from the remote terminal, and activating various buttons on digital and elec- tronic telephones to make telephone calls, set function buttons, change the system time and date, etc. (see Figure 8 and Tables RM-BS ~ BV).

IMPORTANT!

Any digital or electronic telephone button can be activated from the remote terminal at any time while in the Test Mode (even while the end user is using the telephone). Therefore, caution must be used to prevent service interruption or interference. The Test Mode provides status tests to check whether or not a station or CO line is in use. The status checks should always be made before performing other tests (see Table RM-BS).

10.10CO Line Testing

10.11To test CO line transmission, two or three CO lines must be available at the remote site (see Figure 8 and Table RM-BU).

10.12CO line testing is accomplished by using all of the following two methods:

1)Establish a talk path between the two remote stations (B & C) via a CO-to-CO connection through STRATA DK8 or DK16.

>MODE DUMP D MSG SYS

SYS

M60

OUT TO LUNCH

SYS

M61

IN A MEETING

SYS

M62

CALL

SYS

M63

BACK AT

SYS

M64

RETURN ON

SYS

M65

 

SYS

M66

 

SYS

M67

 

SYS

M68

 

SYS

M69

 

D

 

 

FIGURE 6

FIGURE 7

DATA DUMP PRINTOUT EXAMPLE

SAMPLE PRINTOUT OF SYSTEM MESSAGES

-12-

Page 262
Image 262
Toshiba DK 16, DK8 manual Test Mode, Data Dump Printout Example, CO Line Testing, Sample Printout of System Messages