Toshiba DK8, DK 16 manual Bell-even if a headset is also installed on the Hheu

Bell—even if a headset is also installed on the HHEU.

6)Position the HHEU PCB on the standoffs inside the base (Figure 6-10), and secure with the two provided screws.

7A) For 2000-series digital telephones, refer to Figure 6-7 (DKT2010-H) or Figure 6-8 (DKT2010-SD, DKT2020-S, DKT2020-SD), and connect the wire plug of the HHEU PCB to the HHEU connector on the printed circuit board (PCB) on the telephone.

7B) For 1000-series digital telephones, refer to Figure 6-9, and connect the wire plug of the HHEU to the HHEU connector on the PCB of the telephone.

8A) For 2000-series digital telephones, refer to Figure 6-7 (DKT2010-H) or Figure 6-8 (DKT2010-SD, DKT2020-S, DKT2020-SD), and locate the EX.SP strap on the PCB in the telephone. Cut the strap if an HESB will be connected to the HHEU.

8B) For 1000-series digital telephones, refer to Figure 6-9, and locate the EX.SP strap on the upper PCB in the telephone, and cut it if an HHEU will be connected to an HESB for the Loud Ringing Bell option.

9A) For 2000-series digital telephones, refer to Figure 6-7 (DKT2010-H) or Figure 6-8 (DKT2010-SD, DKT2020-S, DKT2020-SD), and locate the HHEU strap on the PCB in the telephone. Cut the strap if a headset will be connected to the HHEU.

9B) For 1000-series digital telephones, refer to Figure 6-9, and locate the HHEU strap on the upper PCB in the telephone. Cut the strap if an HHEU will be connected to a headset.

NOTE:

If the HHEU PCB is removed from the tele- phone, the HHEU strap must be replaced for proper telephone operation.

10)Reinstall the telephone base, and secure it with its four captive screws.

INSTALLATION-STATION APPARATUS

SECTION 100-816-206

MARCH 1993

11)To adjust the volume of the HESB Loud Ringing Bell: Call the telephone connected to the HESB, and adjust the volume control on the back of the HESB and the ring volume control on the telephone.

3.40Carbon Headset/Handset Straps

3.41If a carbon-type handset or headset is con- nected to the handset jack on the side of the telephone, two jumper straps inside the telephone must be cut. Cut the straps in accordance with the following steps:

NOTE:

It is not necessary to cut these straps if the headset is connected to the HHEU.

1)Loosen the four captive screws securing the telephone base (Figure 6-1), and remove the base.

2A) For 2000-series digital telephones refer to Figure 6-7 or 6-8, and cut the CARBON straps, W201 and W202.

2B) For 1000-series digital telephones, refer to Figure 6-9, and cut the CARBON straps, (W301 and W302 on the DKT1020-SD; W201 and W203 on the DKT1020-H).

3)Reinstall the telephone base, and secure it with its four captive screws.

3.50Beep Strap

3.51A "beep" sounds whenever a dialpad button or feature button is pressed on a digital telephone. To eliminate this beep follow the procedure below:

1)Loosen the four captive screws securing the telephone base (Figure 6-1), and remove the base.

2A) For 2000-series digital telephones, refer to Figures 6-7 or 6-8,and cut the BEEP strap.

2B) For 1000-series digital telephones, refer to Figure 6-9, and cut the BEEP strap.

3)Reinstall the telephone base, and secure it with its four captive screws.

6-9