Toshiba DK8, DK 16 manual Diu

INSTALLATION-WIRING DIAGRAMS SECTION 100-816-208 MARCH 1993

TO PDKU/KCDU/BASE UNIT

W/FEMALE CONNECTOR			BRIDGING
			CLIPS
W-BL	26
		1		1
BL-W	1
W-O	27	2		2
O-W	2	3		3
W-GN	28	4		4
GN-W	3	5		5
W-BR	29	6		6
BR-W	4	7		7
W-S	30	8		8
S-W	5	9		9
R-BL	31	10		10
BL-R	6	11		11
R-O	32	12		12
O-R	7	13		13
R-GN	33	14		14

STATION CABLING

(-)	T1 (VOICE/DATA)
(GND)	R1 (VOICE/DATA)
(-)	PT1 (ADD, POWER)
(GND)	PR1 (ADD. POWER)
T2
R2	CIRCUIT 2 TO DKT2
PT2
	OR PDIU-DS
PR2
T3
R3	CIRCUIT 3 TO DKT3
PT3
	OR PDIU-DS
PR3
T4
R4	CIRCUIT 4 TO DKT4
PT4

JACKETED TWISTED PAIRS 24AWG (1 OR 2 PAIR, SEE NOTE 2)

R					GN
R1					T1
BK					Y
PT1					PR1
W					BL
					RJ11
6	5	4	3	2	1

CONNECTOR	GN-R	8	15	15
	R-BR	34	16		16
	BR-R	9	17		17
			18		18

PR4	OR PDIU-DS
T5
R5	CIRCUIT 5 TO DKT5

2- OR 4-WIRE MODULAR CORD TO RJ11 JACK ON BOTTOM

DB-25
FEMALE	GND	(-)	GND	(-)
CONNECTOR	PR	T	R	PT

	R-S	35	19	19
	S-R	10
AMP			20	20
	BK-BL	36
			21	21
	BL-BK	11

PT5	OR PDIU-DS
PR5
T6
R6

OF PDIU-DI/ PDIU-DI2

RS-232

TO PERSONAL COMPUTER OR ASCII TERMINAL, ETC.

W/MALE	BK-O	37	22	22
			23	23
	O-BK	12
			24	24
	BK-GN	38
			25	25
CABLE
	GN-BK	13
			26	26
	BK-BR	39
			27	27
-PAIR	BR-BK	14
			28	28
	BK-S	40
			29	29
25	S-BK	15	30	30
	Y-BL	41
			31	31
	BL-Y	16
			32	32
	Y-O	42
			33	33
	O-Y	17
			34	34
	Y-GN	43
			35	35
	GN-Y	18
			36	36
	Y-BR	44
			37	37
	BR-Y	19
			38	38
	Y-S	45
			39	39
	S-Y	20
			40	40
	V-BL	46
			41	41

		CIRCUIT 6 TO DKT6
	PT6
		OR PDIU-DS
	PR6
	(-)	T7 (VOICE/DATA)
	(GND)	R7 (VOICE/DATA)
(-)		PT (ADD, POWER)
	(GND)	PR (ADD. POWER)
	T8
	R8	CIRCUIT 8 TO DKT8
	PT8	OR DDSS
	PR8

(SEE NOTE 2)

R

R8

BK

PT8

W

CABLE3

(SEE SECTION 100-016-207)

DIGITAL TELEPHONE (DKT 1)

(WITH OR WITHOUT PDIU-DI/PDIU-DI2)

GN

T8

Y

PR8

BL

RJ11

BL-V	21	42	42
V-O	47
		43	43
O-V	22
		44	44

NOT USED

6 5 4 3 2 1

V-GN	48	45	45
GN-V	23
		46	46
V-BR	49
		47	47
BR-V	24
		48	48
V-S	50
		49	49
S-V	25
		50	50

66M150 SPLIT BLOCK

GND	(-)	GND	(-)
PR	T	R	PT

2- OR 4-WIRE		DB-25
		FEMALE CONNECTOR
MODULAR CORD
				TO MODEM, PRINTER,
TO RJ11 JACK ON
THE BACK SIDE				OR HOST COMPUTER
OF PDIU-DS	DIU			ETC.
			TOSHIBA

NOTES:	POWER	READY CONNECT	RS-232
1. Voltage levels:			CABLE3
			(SEE SECTION 100-016-207)
T, PT = -26.3 ~ 27.8 VDC		PDIU-DS
R, PR = 0.0 VDC (GND)
(Reference to SG ground)

2.T/R wires are always required; PT/PR are additional power wires required only for long station runs or when operating on reserve power per Table 8-D. PT/PR may be used with normal station runs also.

RS-232 cable length is max 50 ft with 24 AWG wire.

3 DIUs can be connected to circuits 1 ~ 7 with PDKU1; all Base Unit, KCDU, and PDKU2 digital circuits support DIUs.

4.Expansion Unit slots 04 and 05 only can support DIU.

5.KCDU provides circuits 1 ~ 4 only.

FIGURE 8-11

DK16 MDF WIRING FOR DIGITAL TELEPHONES (DKTS) WITH PDIU-DI/PDIU-DI2 AND PDIU-DS TO PDKU, KCDU, OR BASE UNIT

8-15