Toshiba DK8, DK 16 manual Installation-Peripherals

program the VM machine to dial the following sequences (In Program 10-2, turn LED 04 ON):

1)To set a MW LED, the VM machine must dial 6 3 + station number.

2)To cancel a MW LED, the VM machine must dial 6 4 + station number.

NOTE:

Only dial codes 63 and 64 are set in the VM device configuration; the VM device will dial the station number automatically to set/cancel the Message Waiting indication LED.

•No Conference VM—Prevents undesired CO line three-party connections during VM call trans- fers. All VM ports should be set for no conference (Program 31, LED 09).

•Privacy Override Deny—Prevents stations from overriding (breaking in) in-progress VM calls (Program 31, LED 18).

•End-to-EndSignaling—Allows VM port DTMF operation. All VM ports should be set for end-to-end signaling (Program 31, LED 17).

NOTE:

The DK8 QRCU or DK16 K4RCU must be installed to allow End-to-End Signaling.

•VM to VM Call Blocking—Prevents VM auto attendant calls from forwarding back to VM auto attendant during supervised transfers (Program 31, LED 04 ON). This will prevent the problem of auto attendant to auto attendant looping connec- tions.

•Receive Auto Call Forward ID Codes—Pro- vides auto digits from call forwarded stations to direct callers to stations’ mailboxes. All VM ports should be set to receive auto ID code (Program 31, LED 16).

•“A” and “D” tones; see Paragraph 7.13.

7.24Voice Mail Program Checklist. The follow- ing items should be verified before programming voice mail:

1)Set Toshiba VP Maintenance Menu system parameters to “D” = STRATA DK8 and DK16

INSTALLATION-PERIPHERALS

SECTION 100-816-207

MARCH 1993

(see Toshiba VP Installation and Maintenance Manual for other parameter settings).

2)STRATA DK8 and DK16 programs:

•Program 92: Initialization clears voice mail auto dial codes.

•Program 03: Verify that the KRCU is pro- grammed in the Base Unit to allow the VM/ AA to send DTMF tones (does not apply to DK8).

•Program 04: Assigns station numbers to VM/AA ports (initialized numbers recom- mended).

•Program 05: First digit of special codes 63 and 64 (initialized numbers recommended).

•Program 10-1: Set the system for voice first, and program the VM/AA device to dial the suffix as “1” after station numbers.

•Program 10-2: Set LED 04 ON for set/cancel operation and 06 ON for the VM to detect 80 msec. tones.

•Program 13: If the VM/AA device is the message center, set the lowest VM port as the message center.

•Program 31: Turn LEDs 05, 09, and 15 ~ 20 ON for the QSTU, KSTU, PESU, or PSTU ports that are connected to the Toshiba VP VM/AA ports. Do not set these options for standard telephone, digital telephone, or elec- tronic telephone station ports. LED 04 should be off if the auto attendant only “BLIND” transfers; if the AA does “Supervise” or “Screened” transfers, set LED 04 ON for auto attendant ports.

NOTE:

A, D, and B tones should be enabled only for VM/AA devices that respond to these tones.

•Program 33: Set the QSTU, KSTU, PESU and PSTU ports that are connected to the VM/AA ports to a hunting sequence, starting with the lowest port hunting to the next high- est port, etc. The last hunt should be to an attendant.

•Program 35: LEDs 01 and 02 must be ON for stations to receive the message indication (Msg LED flashing) from a VM device.

7-31