Toshiba DK8, DK 16 manual DK16 MDF WIRING/AMPLIFIED TWO-CO Line Conference, System Programs

INSTALLATION-WIRING DIAGRAMS SECTION 100-816-208 MARCH 1993

TO PEKU W/FEMALE

CONNECTOR

	W-BL	26
			1
	BL-W	1
			2
	W-O	27
			3
	O-W	2
			4
	W-GN	28
			5
	GN-W	3
			6
	W-BR	29
			7
	BR-W	4
			8
	W-S	30
			9
	S-W	5
			10
	R-BL	31
			11
	BL-R	6
			12
	R-O	32
			13
	O-R	7
			14
	R-GN	33
CONNECTOR			15
	GN-R	8
			16
	R-BR	34
			17
	BR-R	9
			18
	R-S	35
			19
	S-R	10
AMP	BK-BL	36	20
			21
	BL-BK	11
W/MALE			22
	BK-O	37
			23
	O-BK	12
			24
	BK-GN	38
CABLE			25
	GN-BK	13
			26
	BK-BR	39
			27
-PAIR	BR-BK	14
			28
	BK-S	40
			29
25	S-BK	15
			30
	Y-BL	41
			31
	BL-Y	16
			32
	Y-O	42
			33
	O-Y	17
			34

BRIDGING

CLIPS

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

VT1		NOTES:
VR1
	CIRCUIT 1 TO EKT	1.	Amplifier or Repeater must have
DT1
			Automatic Gain Control and be
DR1
			FCC Registered from Part 68.
VT2		2.	Refer to Manufacturer’s Installation
VR2	CIRCUIT 2 TO EKT
DT2			Documentation for Amplifier or
DR2			Line Repeater Pin numbering.
		3. Connect to PEKU or PESU.
VT3
VR3	CIRCUIT 3 TO EKT
DT3
DR3
VT4
VR4
DT4	CIRCUIT 4 TO EKT
DR4					CUSTOMER SUPPLIED
VT5					TWO-WAY AMPLIFIER
VR5						OR
DT5	CIRCUIT 5 TO EKT
				LINE REPEATERS (SEE NOTE 1)
DR5	PEKU (OR PESU) CIRCUIT 6
VT6
VR6	VOICE PAIR			PORT A (CENTRAL OFFICE SIDE)
DT6	NOT USED
DR6
	PEKU (OR PESU) CIRCUIT 7
VT7
VR7	VOICE PAIR			PORT B (SUBSCRIBER SIDE)
DT7	NOT USED			(SEE NOTE 2)
DR7
VT8
						TO 117VAC
VR8	CIRCUIT 8 TO EKT
DT8
DR8
	OCA T1 (OT)
	OCA R1 (OR)

Y-GN	43
		35
GN-Y	18
		36
Y-BR	44
		37
BR-Y	19
		38
Y-S	45
		39
S-Y	20
		40
V-BL	46
		41
BL-V	21
		42
V-O	47
		43
O-V	22
		44
V-GN	48
		45
GN-V	23
		46
V-BR	49
		47
BR-V	24
		48
V-S	50
		49
S-V	25
		50

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

OT2

OR2

OT3

OR3

OT4

OR4

OT5

OR5

OT6

OR6

OT7

OR7

OT8

OR8

CIRCUIT 2

CIRCUIT 3

CIRCUIT 4

CIRCUIT 5

CIRCUIT 6

CIRCUIT 7

CIRCUIT 8

NOT USED

SYSTEM PROGRAMS

•Program 10-3, circuit assignments:

		PEKU OR	PEKU
PROGRAM 10-3	SLOT	PESU PORT	OR PESU
LED	POSITION	NUMBER	CIRCUIT
LED 02, ON	04	A = 17	CKT6
		B = 18	CKT7

•Program 10-1, LED 19 and 20 ON.

•Program 15-5, enable appropriate CO lines for tandem connection.

•Program 78-2, enable appropriate CO lines if amplified DISA is required.

•Program 10-2, LED 18 and 19 ON.

66M150 SPLIT BLOCK

FIGURE 8-27

DK16 MDF WIRING/AMPLIFIED TWO-CO LINE CONFERENCE

8-31