Maretron DCR100 Configuration | Maretron DSM250-01 guide

DSM250 User’s Manual

6.6Maretron DCR100 Configuration

The DSM250 is capable of configuring the Maretron DCR100 DC Relay device. This section describes the configuration of the Maretron DCR100 firmware version 1.1.1. The main DCR100 configuration screen is shown below.

Figure 55 – DCR100 Configuration Screen

6.6.1 Advanced Configuration

Advanced Configuration changes some complex parameters within the device, and should only be performed by an advanced user. Typically advanced configuration is only done at installation and should not need to be done while at sea.

Figure 56 – DCR100 Advanced Configuration Screen

6.6.1.1 Current Sensor Zero Offset Calibration

The DCR100 contains Hall-effect current sensors. In order to ensure maximum accuracy, you should perform this calibration step while there is no current flowing through the current sensors. Move the

Page 68

Revision 1.4.16a

Image 84

Maretron DSM250-01 user manual Maretron DCR100 Configuration, Current Sensor Zero Offset Calibration

Contents

DSM250 Nmea 2000 Multi-function Color Graphic Display DSM250 User’s Manual Revision History Table of Contents VDR Revision 1.4.16a DSM250 User’s Manual Revision 1.4.16a 29.1 Revision 1.4.16a Table of Figures ALM100 Configuration Screen FFM100 Channel #1 Configuration Screen Differential Mode 104 RAA100 Label Configuration 141 Custom Tank Level Calibration Confirmation Screen 171 Numeric Display Example 202 Page DSM250 Features Quick InstallIntroduction Firmware Revision Unpacking the Box Choosing a Mounting LocationMounting the DSM250 Surface Mounting the DSM250 Flush Mounting the DSM250 Surface Mounting the DSM250 Gimbal Mounting the DSM250 Flush Mounting the DSM250 Connecting the DSM250 Checking the Connection Turning the DSM250 On Turning the DSM250 Off Keypad Essentials Navigating in a Menu Choosing a Value from a List Entering a Numeric ValueEntering a Textual Value Entering a Textual Value Enter DSM250 User’s Manual Favorite Screens Categories and Data Types AC Bus AC Generator AC Utility Anchor Watch 5 DCDepth Elec. Distribution Revision 1.4.16a Environment Fluid FlowFuel Management 12 GPS HeadingHumidity Indicator NavigationRudder Pressure/Vacuum Temperature Special DevicesSpeed Tank Transmission 25 VDRVessel Wind Revision 1.4.16a Alerts Alert TypesAlert Terminology Alert Priority Alert States Available Alert Classes Operating Modes Favorite screens modes Menu Mode Main Menu Alert Setup Menu Configuration MenuDevice Configuration Alert Status Device Selection Screen Display Settings Menu Advanced ConfigurationInstallation Description Restore Factory Defaults Primary Device SelectionRefresh Network Information Advanced Information DSM250 Advanced Information Screen Bus Status Color Setup Backlight Color Palette Selection Screen Demo Mode Keyboard Beep Label LanguageSoftware Version Favorite Screens Mode Favorite Screens Setup Menu Favorite Mode Format Setting the Favorite Screen Format Auto Change Interval Window Data Type Units Menu InstanceAlert Title Heading DepthDistance Temperature Boat SpeedWind Speed Wind True Vessel Ref Volume Fluid PressureTime Format Local Time Offset Device Configuration Maretron Network Bus Extender NBE100 Set device label Device Configuration Screen DSM250 User’s Manual Airmar Depth/Speed/Temperature Transducers Advanced Configuration Installation Description NMEA2000 PGN Enable/DisableDevice Instance Clear Speed Calibration Clear Temperature Offset Speed Calibration Temperature Calibration Transducer Depth Offset Resetting the Airmar Speed Sensor Trip Distance Log Trip Log Bennett EP-30 NMEA1 Trim Tabs Configuration Trim Tabs Calibration EP-30 Intermediate Calibration Screen Maretron ACM100 Configuration Current Transformer a Inverse Install Normal Install Current Transformer BCurrent Transformer C Damping Period Power NMEA2000 PGN Enable/DisableDamping Period V, I, F AC Circuit Type AC Device TypeLabel Reset Total Energy Recorded Reset Total Energy Recorded Confirmation Screen Maretron ALM100 Configuration Device Instance ALM100 Nmea 2000 PGN Enable/Disable Screen Instance Test Annunciator Maretron DCM100 Configuration Current Sensor Type DCM100 Nmea 2000 PGN Enable/Disable Screen Current Sensor Zero Offset Calibration Current Sensor Zero Offset Calibration Confirmation Screen DC Type Battery Temperature Charge Efficiency FactorFully Charged Voltage Fully Charged Current Instance Maretron DCR100 Configuration Current Sensor Zero Offset Calibration DCR100 Current Sensor Zero Offset Calibration Screen Channel #1-#6 Configuration Nmea 2000 PGN Enable/DisableChannel #1-#6 Configuration DCR Mode Device Label Operating Mode Switch LockPower Up State Switch Control Maretron DSM200 Configuration ALM InstanceTest Annunciator DSM200 Remote Configuration Screen Remote Device Selection DSM250 User’s Manual Maretron DSM150, DSM250 Configuration DSM150/DSM250 Remote Configuration Screen Copy alarms settings from local display DSM150/DSM250 Remote Device Selection Screen DSM150 Copy alarms settings from local display Copy device selection from local display Copy display settings from local display Copy favorite settings from local display Copy all settings from local display Copy DST100 calibrations from local display DSM150/DSM250 copy all settings from local display DSM150/DSM250 Remote Device Selection Maretron DST100 Configuration DST100 Configuration Screen Calibrating the DSM250 for DST100 Speed through Water Setting the Transducer Depth Offset in a DST100 Resetting the DST100 Trip Distance Log Maretron DST110 Configuration DST110 Configuration Screen Instance Temperature DST110 Nmea 2000 PGN Enable/Disable Screen Calibrating the DST110 Speed DST110 Water Temperature Calibration Screen Setting the Transducer Depth Offset in a DST110 Maretron EMS100 Configuration Engine InstanceBoost Pressure Gauge Type Boost Pressure Sender Type Boost Pressure Sender OffsetDrive Trim Gauge Type Drive Trim Sender Type Drive Trim Sender Offset Oil Pressure Gauge TypeOil Pressure Sender Type Oil Pressure Sender Offset Water Temperature Gauge Type Water Temperature Sender TypeWater Temperature Sender Offset Preset Engine Hours Tachometer Flywheel Teeth Maretron FFM100 Configuration Channel 0 Installation Channel 1 Installation Differential Mode Allow negative flowChannel 0 Allow negative flow Channel 1 Allow negative flow Operating Mode Channel #0… Channel #0 Differential Mode 12.4.1.1Channel Supply/Return12.4.1.2Engine Instance 12.4.1.6Reset Total Volume Recorded 12.4.1.7Temperature Instance12.4.1.8Temperature Source 12.4.1.9Temperature Label Volume Instance Volume LabelChannel #0 Configuration Menu Two Independent Sensors Mode 12.4.2.6Reset Total Volume Recorded 12.4.2.7Temperature Instance12.4.2.8Temperature Source 12.4.2.9Temperature Label Channel #1 Differential Mode Channel #1…Fluid Type 12.5.1.4Temperature Instance 12.5.1.5Temperature Source12.5.1.6Temperature Label 12.5.1.1Channel Supply/Return 12.5.2.1Sensor 12.5.2.2Engine Instance 12.5.2.6Reset Total Volume Recorded 12.5.2.7Temperature Instance12.5.2.8Temperature Source 12.5.2.9Temperature Label Maretron FPM100 Configuration Advanced Configuration… FPM100 Advanced Configuration Screen NMEA2000 PGN Enable/Disable… Channel #0-5 Channel #0-5 Tank 13.2.1.1Function 13.2.1.2Label13.2.1.3Pressure at 4mA 13.2.1.4Pressure at 20mA FPM100 Tank Levels Calibration Menu Custom Calibration Tank Levels Calibration Capacity Estimation Intermediate Level Calibration Rectangular Tank 13.2.1.7Tank Number13.2.1.8Tank Type Fuel Fresh Water Waste Water Live Well Oil Black Water 13.2.1.9Data Damping PeriodChannel #0-5 Pressure/Vacuum 13.2.2.1Function Maretron GPS100 Configuration 13.2.2.4Pressure at 4mA13.2.2.5Pressure at 20mA 13.2.2.6Source GPS100 Advanced Configuration Screen GPS Antenna Altitude Elevation Mask Pdop Mask Configuring Pdop Mask on a GPS100 SNR Mask GPS100 Nmea 2000 PGN Enable/Disable Screen GPS Mode Setting Cold Start GPS Sbas Waas Enable/Disable Configuring GPS Operating Mode on a GPS100 Configuring Sbas on a GPS100 Maretron GPS200 Configuration GPS200 Configuration Screen GPS200 Nmea 2000 PGN Enable/Disable Screen Sbas WAAS,EGNOS,MSAS Enable/Disable Restoring Factory Defaults on the GPS200 Configuring Sbas on a GPS200 Maretron IPG100 Configuration IPG100 Configuration Screen 16.1.3 N2KServer Information 16.1.3.1Client List 16.3 N2KServer Password 16.1.3.2N2KServer Version16.1.3.3License Key Number 16.1.3.4Platinum Licenses Default Gateway Default DNSDhcp IP Address Maretron J2K100 Configuration Data Damping 17.1.4 J1939 Diagnostic Messages J2K100 J1939 Diagnostic Messages Configuration J2K100 Nmea 2000 PGN Enable/Disable Screen Nmea 2000 Instance Engine J2K100 Engine Instance Configuration Transmission Instance 17.6 J1939 Source Address Configuration 17.5 AC/Icemaker Instance Maretron NBE100 Configuration Refresh J1939 source address list Maretron RAA100 Configuration NBE100 Advanced Configuration Screen RAA100 Configuration Screen RAA100 Nmea 2000 PGN Enable/Disable Screen RAA100 Label Configuration Rudder Angle Calibration RAA100 Custom Rudder Angle Calibration RAA100 Center Rudder Angle Calibration Rudder Number Set to American Standard 240-33 ohmSet to European Standard 0-180 ohm RAA100 Setting the Rudder Number Gauge Resistance, + to Sender Gauge Resistance, to Sender RAA100 Setting the to Sender Gauge Resistance Maretron RIM100 Configuration RIM100 Configuration Screen RIM100 Nmea 2000 PGN Enable/Disable Screen Channel Configuration Mode Maretron SIM100 Configuration SIM100 Configuration Screen SIM100 Nmea 2000 PGN Enable/Disable Screen SIM100 Channel Configuration Screen Maretron SSC200 Configuration SSC200 Configuration Screen NMEA0183 Settings 22.1.3.1Baud Rate22.1.3.2Sentence / Rate Selection 22.1.3.3Load Default Sentence / Rate Selection SSC200 Nmea 0183 Sentence/Rate Selection Screen Installation Offset Calibration SSC200 Nmea 2000 PGN Enable/Disable Screen Inverted Installation Entry SSC200 Installation Offset Calibration Screen Magnetic Deviation Calibration SSC200 Magnetic Deviation Calibration Start Screen Magnetic Deviation Status Rate of Turn Damping Period Rate of Turn Zero Offset Calibration Variation Source Entry Setting Variation Source to Nmea 0183 Only Setting Variation Source to Nmea 2000 Only DSM250 User’s Manual Maretron TLA100 Configuration TLA100 Configuration Screen TLA100 Nmea 2000 PGN Enable/Disable Screen Tank Capacity Configuring the Tank Capacity Tank Levels Calibration Performing Custom Calibration of the Tank Level Adapter Tank Levels Calibration Capacity Estimation Intermediate Level Calibration American Standard Sender Calibration European Standard Sender Calibration Tank Number Tank Type Configuring the Tank Type Configuring the Operating Mode Configuring the to Sender Gauge Resistance Maretron TLM100 Configuration TLM100 Configuration Screen TLM100 Nmea 2000 PGN Enable/Disable Screen Tank Levels Calibration Performing Custom Calibration of the Tank Level Monitor Empty Level Calibration Revision 1.4.16a Rectangular Tank Selection Fuel Fresh Water Waste Water Maretron TLM150 Configuration Maretron TLM200 ConfigurationLive Well Oil Black Water Maretron TMP100 Configuration TMP100 Configuration Screen TMP100 Nmea 2000 PGN Enable/Disable Screen TMP100 Channel Configuration Screen Source Maretron USB100 Configuration USB100 Configuration Screen USB100 Device Selection Screen Maretron VDR100 Configuration VDR100 Configuration Screen Maretron WSO100 Configuration WSO100 Configuration Screen Instance Humidity Instance Pressure WSO100 Nmea 2000 PGN Enable/Disable Screen WSO100 Device Label Menu WSO100 Configuration Aborted Due to Low Wind Speed Wind Data Damping Period Barometric Pressure Outside Temperature Outside Humidity Setting the Outside Temperature Data Display Types Anchor Watch Display Compass Rose Display Compass Rose Display Course Up Example Gauge Display Gauge Display Example GPS Status Display Hdop Numeric Display Numeric Display Example Configuration of Rolling Road Display Rolling Road Line Graph Weather Display Weather Display Moon Phase Display Wind RoseTrim Tab Display Swing Meter Display Tank Gauge Display Switch/Breaker Display Tank Gauge Display Selection of an Individual Switch/Breaker DSM250 User’s Manual Favorite Screen Showing Highlighted Switch/Breaker Displaying Active Alerts Alert Status Screen Accepting or Cancelling an Alert From a Favorite ScreenFrom the Alert Status Screen Adding an Alert Adding a New Alert Enable/Disable Control Alert TypePriority Trigger Configuration Trigger SourceDescription Location Trigger Configuration High Alert Parameters Trigger Type is Low Alert Parameters Low Alert Parameters Trigger Configuration Low Alert Trigger Type is Data Unavailable Alert Trigger Configuration Data Unavailable Alert Trigger Type is On Alert Trigger Configuration On Alert Trigger Type is Off Alert Trigger Type is Error Alert Trigger Configuration Editor Tripped Alert Trigger Type is Outside Radius Alert Trigger Configuration Outside Radius Alert Trigger Type is Inside Radius Alert Trigger Configuration Inside Radius Alert Trigger Type is Anchor Alert 7.10.1Trigger Configuration GPS Quality Alert Trigger Type is GPS Quality Alert Trigger Type is Direction Alert Direction Alert Parameters 7.11.1Trigger Configuration Direction Alert Trigger Type is Time Alert 7.12.1Trigger Configuration Time Alert Local AudibleTone Operating Mode Moored Operating Mode UnderwayRemote Annunciators Operating Mode Anchored Deleting an AlertScope Editing an Alert Deleting Alert List Editing an Alert Setting the Vessel Operating Mode Advanced Configuration Restore Factory Defaults Remote Alert AudibleFlashing Screen Restore Factory Defaults Confirmation Maintenance Troubleshooting Technical Specifications PGN # DSM250 User’s Manual Revision 1.4.16a DSM250 User’s Manual Technical Support Installation Template Flush Mounting Template Maretron 2 Year Limited Warranty Warranty Return Procedure