PoE tab for ports, Color Description | Nortel Networks 2500 Series

Editing and viewing switch PoE conﬁgurations using Device Manager 175

Color	Description

Red P	Specifies that the power and detection mechanism for the
	port is disabled.

Orange P	Specifies that the power and detection mechanism for the port
	is enabled. However the port is not currently delivering power.

White/Gray P	Specifies that the power and detection mechanism for the
	port is unknown.

ATTENTION

The coloring scheme for data aspect and the power aspect are independent of each other. With this GUI enhancement, you can view the initial status for both data and power aspect for the port.

PoE tab for ports

The PoE tab lets you conﬁgure PoE power settings for ports.

To view the PoE tab, use the following procedure:

Step Action

1Select the port you want to edit.

2Do one of the following:

•Double-click the selected port.

•From the shortcut menu, choose Edit.

•From the Device Manager main menu, choose Edit > Port.

•On the toolbar, click Edit.

The Port dialog box appears with the Interface tab displayed.

3Click the PoE tab. The PoE tab appears.

Edit Port dialog box— PoE tab

Nortel Ethernet Routing Switch 2500 Series

Overview — System Conﬁguration

NN47215-500 (323162-B) 02.02 Standard

4.1 19 November 2007

Copyright © 2007, Nortel Networks

Image 175

Nortel Networks 2500 Series manual PoE tab for ports, Color Description, Edit Port dialog box- PoE tab

Contents

Overview System Conﬁguration Restricted rights legend TrademarksStatement of conditions General Nortel Networks software license agreementPage Contents System conﬁguration software features Getting Started with Device Manager 101 Using the Web-based management interface 145 System conﬁguration using the CLI 177 Copyright 2007, Nortel Networks Ethernet port management using the CLI 233 Conﬁguring ports using Device Manager 303 Troubleshooting 337 Contents Other changes FeaturesConﬁguring daylight savings time using the device manager New in this release New in this release This guide uses the following text conventions IntroductionBefore you begin Text conventions Bold body text Introduction Protocols menu Related publications Getting help through a Nortel distributor or reseller How to get helpGetting help over the phone from a Nortel Solutions Center Getting help from the Nortel web site How to get help Introduction Front panel Ethernet Routing Switch 2500 Series hardware Ethernet Routing Switch 2526T front panel Ethernet Routing Switch 2550T-PWR Console port Port connectors SFP Gbic Support on the Ethernet Routing Switch 2500 SeriesGigabit Interface Converter LED display panel Auto-MDI/MDI-X PWR Kensington lock Back panelLabel Type Color State Meaning Cooling fans AC power receptacle Read immediately Country/Plug Specifications Typical plug DescriptionBitte sofort lesen Leggere attentamente Lisez ceci immédiatementSírvase leer inmediatamente Avertissement Network conﬁguration examples Small ofﬁce desktop switch application Ethernet Routing Switch 2500 Series used as a desktop switch Branch ofﬁce workgroup switch application Conﬁguring power workgroups and a wiring closet switch Medium sized ofﬁce wiring closet switch application Conﬁguring power workgroups and a wiring closet switch Ethernet Routing Switch 2500 Series hardware Stacking capabilities Nortel Ethernet Routing Switch 2500 Series stacking Stacking functionality delivery Stack enabled switchesStandalone conﬁguration with license ﬁles Syntax for the copy tftp license command is Working with license ﬁles using the CLI Show license all command output Copying the license ﬁle using the Java Device Manager Step Action License Download Following table describes the ﬁelds on the License DownloadLicense Download page ﬁelds Fields Description Stack conﬁguration To set up a stack, do the following Rear-ports mode command Show rear-ports mode command Conﬁguring the operational mode on rear ports using the CLIRear-ports mode command Show rear-ports mode command Rear panel components Unit Select switchShow rear-ports mode command output Rear ports and stacking Cascade Down port Connecting stack cablesCascade Up port Base Unit Cascade Cable Cascade Cable used for return Initial stack installationStack MAC address Stack conﬁgurations Cascade down stack conﬁguration Regardless of stack conﬁguration, the following applies Temporary base unitCascade up stack conﬁguration Redundant cascade stacking Adding/Replacing a stack unit Removing a stack unitRedundant cascade stacking Auto Unit Replacement AUR function CFG mirror process in stack CFG mirror image process CFG mirror images in the stack after adding unit CFG mirror images after removing unit CFG mirror images in the stack after removing the BU unit Restoring a CFG image Step Action Synchronizing the CFG mirror images with CFG images Conﬁguring AUR using the CLIShow stack auto-unit-replacement command Syntax for this command is No stack auto-unit-replacement enable command Stack auto-unit-replacement enable commandDefault stack auto-unit-replacement enable command Displaying unit stack uptime Conﬁguring AUR using Device Manager Nortel Ethernet Routing Switch 2500 Series stacking Switch management features System conﬁguration software featuresConﬁguration and switch management Login banner Console port settingsSwitch banner User name and password Logging Login screen Using Sntp Autosave feature Using DNS to ping and Telnet Setting local time zoneConﬁguring with CLI Choosing a BootP request mode BootP automatic IP conﬁguration/MAC address BootP or Default IP BootP Always BootP or Last Address BootP or Default IPBootP Always BootP or Last Address Flash memory storage Switch software image storage BootP DisabledBootP or Last Address Default BootP setting Requirements Conﬁguration File Download/UploadBinary conﬁguration ﬁle Autotopology Link Layer Discovery Protocol Ieee 802.1ab Ascii conﬁguration ﬁle Connectivity and management information Lldp operational modesHow Lldp works System conﬁguration software features Custom Autonegotiation Advertisements Ethernet port management featuresConﬁguring Lldp using the CLI Autosensing and autonegotiation High speed ﬂow control Symmetric mode RFCs Other featuresAsymmetric mode Rate Limiting Conﬁguration Standards CLI Basics CLI command modes CLI command mode hierarchy Command mode prompts and entrance/exit commands Interface FastEthern Port numbering Port numbering in Standalone Mode Ethernet Routing Switch 2500 Series banner Accessing CLIPress Ctrl+Y, and the CLI prompt appears Getting help Setting the system username and passwordBasic navigation End command Exit command Reload command Shutdown command General navigation commandsKeystroke navigation Help command Help command output No commandDefault command Logout command Conﬁgure command parameters and variables Enable commandConﬁgure command Interface command Syntax for the end command is Disable commandEnd command Exit command Exit command has no parameters or variables Reload command Shutdown command Shutdown command parameters and variables Parameters Description Variables Show sys-info commandShow sys-info command Show tech command Managing basic system information Show sys-info command output Show tech commandShow tech command output Managing MAC address forwarding database table Show mac-address-table command Default mac-address-table aging-time command Mac-address-table aging-time commandShow mac-address-table command output CLI Basics Installing Device Manager Device Manager basics Installing Device ManagerGetting Started with Device Manager Installing JDM on Windows Installing JDM on Unix or Linux JDM installation precautionsInstalling the Device Manager software Installing JDM on Windows Removing previous versions of JDM on Windows Windows minimum requirements Installing JDM on Windows from the web Installing JDM on Windows from the CDTo access the JDM software from the installation CD InstallAnywhere Introduction dialog box Executing the JDM installation software on Windows Click Next Choose Install Set dialog boxLicense Agreement dialog box Feature Sets dialog box Click Next Choose Shortcut Folder dialog box appears Choose Install Folder dialog boxChoose Shortcut Folder dialog box Pre-Installation Summary dialog box Install Complete dialog box Installing JDM on Unix or Linux Installing JDM on Linux from the CD Installing JDM on Solaris from the CDMinimum requirements Installing JDM on Unix or Linux from the web Executing the JDM installation software on Unix or Linux Do one of the following Click Next Choose Install Set dialog box appears Feature Sets dialog box Pre-Installation Summary dialog box appears Installing Java Device Manager dialog box Removing JDM in Unix or Linux environments Starting Device Manager Device Manager basics Device Manager window Setting the Device Manager properties Properties dialog box ﬁelds Area Default Properties dialog boxType information and select check boxes Click OK Following table describes the Properties dialog box ﬁelds Application Control Area Field DescriptionPolling Web Management From JDM To display the device view, use the following procedureOpening a device Application Launch Telnet Following table describes the Open Device dialog box ﬁelds Press Ctrl+O Open Device dialog box appears Field Description SNMPv3 Click Open Device view Device Manager windowParts of the Device Manager window Toolbar Use the menu bar to set up and operate the Device ManagerMenu bar commands page 127 describes the Menu Bar commands Menu bar Selecting objects Device viewToolbar buttons Button Name Description Menu bar equivalent To select a single object Selecting a single objectSelecting multiple objects Viewing information about a Gbic port Interface tab LEDs and ports Color port legend Switch unit shortcut menuShortcut menus Port color codes Color Description Port shortcut menu commands Command Description Switch unit shortcut menu command Command DescriptionPort shortcut menu Device Manager buttons Button Name Description Using the buttons in Device Manager dialog boxesEditing objects Status bar Types of statistics Working with statistics and graphsTypes of statistics Statistic Description Statistic Description Types of graphsLine graph Area graph Bar graph Pie graph Statistics for single and multiple objectsInterface statistics for a single port Types of statistics Viewing statistics as graphs Viewing statistics as graphsInterface statistics for multiple ports Statistics dialog box for a port Opening an SSH connection to the device Telnet sessionGraph dialog box buttons Button Name Description Opening the web-based management home Web-based management home Trap log Online Help Help ﬁle locations Platform Default path Getting Started with Device Manager Requirements Using the Web-based management interface Web-based management interface home Logging in to the web-based management interface Menu MenuMain headings and options Main menu titles Option Adac Main menu titles Option Menu icons Button or icon Description Management Console To view stack information Viewing stack informationIcons Name Description Stack Information screen ﬁelds Section Fields Description Stack Information Section Fields Description Switch InformationSwitch Information page ﬁelds Description Viewing summary information To view or renumber devices within the stack framework Changing stack numberingStack Numbering Stack Numbering screen ﬁelds Field Range Description Identifying unit numbers Identifying Unit Numbers 157 Status codes on PoE ports Diagnosing and correcting PoE problemsConﬁguring PoE switch parameters using the CLI Poe poe-pd-detect-type command Legacy Poe poe-power-usage-threshold command No poe-shutdown command Conﬁguring PoE port parameters using the CLIPoe poe-trap command No poe-trap command Poe poe-shutdown command No poe-shutdown commandNo poe-shutdown command parameters and variables Poe poe-priority command parameters and variables Poe poe-priority commandPoe poe-shutdown command parameters and variables Syntax for the poe poe-prioritycommand is Poe poe-limit command parameters and variables Poe poe-limit commandSets the port priority as Show poe-main-status command Displaying PoE conﬁguration using the CLI Show poe-port-status command parameters and variables Show poe-port-status command Status Show poe-power-measurement commandShow poe-port-status command output Enter the ports for which you want to display Show poe-power-measurement command output Conﬁguring PoE using web-based managementDisplaying and conﬁguring power management for the switch Power measurements Global Power Management page items Description Displaying and conﬁguring power management for the switchDisplaying and conﬁguring power management for the ports Global Power Management End Port Property Displaying and conﬁguring power management for the portsPort Property page appears Port Property Following table describes the items on the Port Property Description PoE tab for a single unit PoE tab items for a single unit Description Edit Unit dialog box-PoE tab for a single unit ERS 2550T-PWR with PoE ports Device Manager display for PoE ports Color Description PoE tab for portsEdit Port dialog box- PoE tab PoE tab items page 176 describes the PoE tab items PoE tab itemsPoE tab items Description IP notation System conﬁguration using the CLI Ip address command parameters and variables Ip address commandAssigning and clearing IP addresses No ip netmask command Default ip address commandNo ip address command Default ip netmask command No ip default-gateway command Ip default-gateway commandIp default-gateway command parameters and variables Show ip command Default ip default-gateway command Show ip address command output Show ip address commandShow ip address command parameters and variables Show ip command output Ping command is executed in the User Exec command mode Ping commandPinging Ping command responses Resetting the switch to default conﬁgurationUsing DNS to ping and telnet Show ip dns command Ping command Ip name-server command Show ip dns command output Show ip dns command There is no default value for this command Ip name-server command No ip name-server command parameters and variables No ip name-server commandIp domain-name command Ip name-server command parameters and variables Conﬁguration Management No ip domain-name commandDefault ip domain-name command Conﬁgure network command Conﬁgure network command parameters and variables Conﬁgure network commandShow conﬁg-network command Configure network command is executed in the User Exec mode Show conﬁg-network command Ascii Conﬁguration Generator Show running-conﬁg commandShow running-conﬁg command Copy running-conﬁg tftp command Show conﬁg-network command output Show running-conﬁg command output Copy running-conﬁg tftp command Show terminal command Terminal command Setting the terminalShow terminal command Terminal command Show cli command is executed in the User Exec command mode Show cli commandTerminal command is executed in the User Exec mode Terminal command parameters and variables Show cli command output Syntax for the show sys-infocommand isDisplaying system information Ip bootp server command parameters and variables Setting boot parametersBoot command Ip bootp server command Default ip bootp server command No ip bootp server commandSetting Tftp parameters Tftp-server command parameters and variables Show tftp-server commandTftp-server command Copy conﬁg tftp command Copy tftp conﬁg command Copy conﬁg tftp command parameters and variables No tftp-server commandDefault tftp-server command Copy conﬁg tftp command Copy tftp conﬁg command parameters and variables Copy tftp conﬁg commandCustomizing the opening banner Describes the parameters for the banner command Banner command for displaying bannerShow banner command Show banner command parameters and variables Displaying the ARP table No banner commandShow interfaces command Show interfaces command Show interfaces conﬁg command Show interfaces names command output Show interfaces command parameters and variablesShow interfaces command output Show interfaces verbose command output Show interfaces conﬁg command Saving the conﬁguration to Nvram Copy conﬁg nvram commandWrite memory command Show interfaces conﬁg command output Show autosave command Save conﬁg commandEnabling and disabling autosave Show autosave command has no parameters or variables Autosave enable commandNo autosave enable command Default autosave enable command Show sntp command Show sntp command output Sntp enable commandNo sntp enable command Sntp server primary address command No sntp server command parameters and variables Sntp server secondary address commandNo sntp server command Default is Sntp sync-interval command parameters and variables Sntp sync-now commandSntp sync-interval command Syntax for the sntp sync-nowcommand is Clock time-zone No clock time-zone Clock summer-time Setting local time zoneDefault sntp command Default sntp command parameters and variables Clock summer-time Clock time-zone command parameters and variablesClock time-zone No clock time-zone No clock summer-time Clock summer-time command parameters and variablesShow clock time-zone Show clock time-zone output Autotopology command No autotopology commandEnabling Autopology Show clock summer-time Show autotopology settings Autotopology commandNo autotopology command Default autotopology command Show autotopology nmm-table Conﬁguring Lldp using the CLIShow autotopology settings command output Show autotopology nmm-table command output 32768 Lldp command Lldp conﬁg-notiﬁcation command parameters and variables Default lldp commandLldp conﬁg-notiﬁcation command Default lldp command parameters and variables Default lldp conﬁg-notiﬁcation command No lldp conﬁg-notiﬁcation commandSpecifies the ports affected by the command No lldp tx-tlv command parameters and variables Lldp tx-tlv commandNo lldp tx-tlv command Lldp tx-tlv command parameters and variables Lldp status command Default lldp tx-tlv commandDefault lldp tx-tlv command parameters and variables No lldp status command parameters and variables No lldp status commandDefault lldp status command Lldp status command parameters and variables Show lldp command parameters and variables Show lldp commandDefault lldp status command parameters and variables Show lldp command is executed in the User Exec command mode Show lldp mgmt-sys-data command output Show lldp local-sys-data command output Show lldp port command parameters and variables Show lldp port commandShow lldp stats command output Show lldp port neighbor-mgmt-addr command output Show lldp port neighbor command output Show lldp port tx-stats command output Show lldp port rx-stats command output Conﬁguring LEDs to blink on the display panel Show lldp port tx-tlv command outputUpgrading software Download command parameters and variables Download commandDownload command Syntax for the download command is Download message System conﬁguration using the CLI Shutdown port command parameters and variables Ethernet port management usingShutdown command for the port Shutdown command for the port No shutdown command No shutdown command parameters and variables No shutdown commandShutdown port command output Name command No name command Default name command Name commandNaming ports Default name command parameters and variables No name commandDefault name command No name command parameters and variables Speed command Setting port speed Default speed command parameters and variables Default speed command Default duplex command Duplex command Enabling ﬂow control ﬂowcontrol commandDefault duplex command parameters and variables ﬂowcontrol command parameters and variables No ﬂowcontrol command parameters and variables No ﬂowcontrol command Default ﬂowconrtol command parameters and variables Default ﬂowcontrol commandEnabling rate-limiting Show rate-limit command output Show rate-limit commandRate-limit command Rate-limit command parameters and variables Default rate-limit command No rate-limit commandEnabling Custom Autonegotiation Advertisements Cana Enter ports for which you want the current Show auto-negotiation-advertisements commandShow auto-negotiation-capabilities command Show auto-negotiation-advertisements command output Auto-negotiation-advertisements command Default auto-negotiation-advertisements command No auto-negotiation-advertisements command Enter ports for which you want to set default Viewing Unit information Conﬁguring the switch using Device Manager To open the Unit tab To open the Rate Limit tab, use the following procedureUnit tab Rate Limit tab Rate Limit tab Following table describes the Rate Limit tab ﬁeldsRate Limit tab ﬁelds Field Description Rear Ports Mode tab Following table describes the Rear Port Mode tab itemsRearPortOperMode Following table describes the Globals tab ﬁelds Viewing switch IP informationTo open the Globals tab, use the following procedure Globals tab Edit IP dialog box IP Address tab Addresses tabFollowing table describes the Address tab ﬁelds Globals tab ﬁelds Field and MIB Description Association ARP tab ﬁelds Field Description ARP tabFollowing table describes the ARP tab ﬁelds Edit IP dialog box ARP tab TCP tab ﬁelds Field Description TCP tabFollowing table describes the TCP tab ﬁelds TCP tab UDP Listeners tab TCP Connections tabTCP Connections tab ﬁelds Field Description UDP Listeners tab ﬁelds Field Description Editing the chassis conﬁguration Edit Chassis dialog box System tab System tab System tab ﬁelds Field Description Following table describes the System tab ﬁelds Base Unit Info tab Base Unit Info tab ﬁelds Field Description Following table describes the Base Unit Info tab ﬁelds Stack Info tab ﬁelds Field Description Value is 4th flr wiring closet in blg aStack Info tab Edit Chassis screen-Stack Info tab 264 Conﬁguring the switch using Device Manager Agent tab Edit Chassis dialog box Agent tab Following table describes the Agent tab ﬁeldsAgent tab ﬁelds Field Description Power Supply tab ﬁelds Field Description PowerSupply tabFollowing table describes the PowerSupply tab ﬁelds Edit Chassis dialog box PowerSupply tab Following table describes the Fan tab ﬁelds Fan tabEdit Chassis dialog box Fan tab Edit Chassis dialog box Banner tab Banner tab Telnet window with default banner To set the default banner, use the following procedureTo disable the banner To check that the banner is disabled Custom Banner tab To create a Custom Banner, use the following procedureEdit Chassis dialog box Custom Banner tab FileSystem Conﬁg/Image/Diag File tab dialog box Working with conﬁguration ﬁlesFileSystem dialog box FileSystem Conﬁg/Image/Diag ﬁle dialog box ﬁelds Ascii conﬁg ﬁle File system Ascii Conﬁg File dialog box Save Conﬁguration tabAscii Conﬁg File tab ﬁelds Field Description Save Conﬁg tab Following table describes the Save Conﬁguration tab ﬁeldsSave Conﬁguration tab ﬁelds Field Description Conﬁguring Sntp Working with SntpSNTPClock dialog box SNTPClock dialog box ﬁelds Field Description Following table describes the Sntp dialog box ﬁelds Conﬁguring daylight savings time using the device manager Conﬁguring local time zone using the device manager Topology tab Topology Table tab Displaying topology information using Device ManagerTo view topology information, use the following procedure Topology tab Topology Table tab Diagnostics dialog box Topology tabTopology tab ﬁelds Field Description Lldp Globals tab Conﬁguring Lldp using Device ManagerDiagnostics dialog box Topology Table tab Following table describes the Topology Table tab ﬁelds Lldp dialog box appears with the Globals tab displayed Lldp Globals tabLldp Globals tab Lldp Globals tab ﬁelds Field Description 284 Conﬁguring the switch using Device Manager Port tab Following table describes the Port tab ﬁelds Click the Port tab. The Port tab appearsPort tab ﬁelds Field Description TX Stats tab TX Stats tab ﬁelds Field Description Graphing Lldp transmit statisticsFollowing table describes the TX Stats tab ﬁelds TX Stats tab Following table describes the RX Stats tab ﬁelds RX Stats tabRX Stats tab ﬁelds Field Description 290 Conﬁguring the switch using Device Manager Local System tab Graphing Lldp receive statisticsLocal System tab appears Local System tab ﬁelds Field Description Local Port tabFollowing table describes the Local System tab ﬁelds Local System tab Local Port tab ﬁelds Field Description Following table describes the Local Port tab ﬁelds Local Management tab ﬁelds Field Description Local Management tabFollowing table describes the Local Management tab ﬁelds Local Management tab Neighbor tab Neighbor tab ﬁelds Field Description Following table describes the Neighbor tab ﬁelds Neighbor Mgmt Address tab Neighbor Mgmt Address tab ﬁelds Field Description Neighbor Mgmt Address tab Unknown TLV tab ﬁelds Field Description Unknown TLV tabFollowing table describes the Unknown TLV tab ﬁelds Unknown TLV tab Organizational Deﬁned Info tab Organizational Deﬁned Info tabOrganizational Deﬁned Info tab ﬁelds Field Description Field Description 302 Conﬁguring the switch using Device Manager Viewing and editing a single port conﬁguration Conﬁguring ports using Device Manager Interface tab for a single port Interface tab ﬁelds Interface tab ﬁeldsPort dialog box Interface tab Interface tab ﬁelds for a single port Field Description To view or edit the conﬁgurations of multiple ports Viewing and editing multiple port conﬁgurations Interface tab for multiple ports Interface tab for multiple ports Interface tab ﬁelds for multiple ports Field Description 310 Conﬁguring ports using Device Manager Administrative options available to you are Administering the switch using web-based managementViewing system information System Information Quick StartSystem Information page items Description Quick Start Items on the Quick Start Section Description Conﬁguring system security Reset page message Rebooting the Ethernet Routing Switch 2500 SeriesFrom the main menu, choose Administration Reset Reset warning message displays Logging out of the management interface Reset to Default page message Logout message Administering the switch using web-based management Conﬁguring BootP, IP, and gateway settings Conﬁguring the switch using web-based managementSwitch conﬁguration options available to you are IP page items Section Range Description Following table describes the items on the IP Section Range Description Conﬁguring BootP, IP, and gateway settings Modifying system settings System page items Range Description To conﬁgure system settings, use the following procedure Type information in the text boxes Click Submit Conﬁguring switch port statusRange Description Port Management Following table describes the items on the Port Management Click Submit Port row of your choice, select from the lists High Speed Flow Control Conﬁguring high speed ﬂow controlHigh Speed Flow Control page items Range Description To download a switch image, use the following procedure Downloading switch imagesSoftware Download Software Download page ﬁelds Fields Range Description Following table describes the ﬁelds on the Software Download 100 Mb/s port status LEDs ports 18 to Downloading Ascii conﬁguration ﬁles Ascii Conﬁguration ﬁle download page items Description Ascii Conﬁguration ﬁle download Type information in the text boxes, or select from a list Conﬁguration File Setting items Range Description Parameters not saved to the conﬁguration ﬁle From the main menu, choose Conﬁguration Console/Comm Port Conﬁguring port communication speedConsole/Communication Port page items Conﬁguring Rate Limiting Conﬁguring Rate LimitingSelect from the list Rate Limiting Following table describes the items on the Rate LimitingRate Limiting page items Section Description Normal power-up sequence Port connection problems TroubleshootingDiagnosing and correcting problems Interpreting the LEDs Diagnosing and correcting problems Normal power-up sequence Corrective actions Symptom Probable cause Port connection problemsAutonegotiation modes Port interface DB-9 Console port connector Appendix a DB-9 RS-232-D Console/Comm Port connector Ring indicator not used Pin number Signal Factory default settings Field Default setting Appendix B Default settings Field Default setting Pvid Packet Type Both Snooping Disabled Field Default setting Field Default setting Field Default setting Appendix B Default settings Appendix C Sample BootP conﬁguration ﬁle Appendix C Sample BootP conﬁguration ﬁle CLI command list Command Appendix D Command List Security Configuration and Management Nortel Ethernet Routing Switch Default tftp-server command Configuration IP Multicast NN47215-503 Ip default-gateway command No autosave enable command No banner command No logging remote level No snmp-server No tftp-server command Save config command Show banner command Show poe-port-status command Show running-config command Show terminal command Show tftp-server command Snmp-server host host-ip port Spanning-tree mstp max-hop 100 Terminal command Vlan create Appendix D Command List Environmental speciﬁcations AC power speciﬁcationsParameter Operating specification Storage specification Appendix E Technical speciﬁcations Performance speciﬁcations Physical dimensionsNetwork protocol and standards compatibility Electromagnetic emissions Safety agency certiﬁcation Electromagnetic immunity Index Index Eeprom 132 Gbic Viewing 129 No banner command No autotopology command Index Index Sntp 68, 68, 208 181 Software version requirements Unix Index Index Page Overview System Conﬁguration