Emerson Process Management 5300 manual Parameter Index Units Description Number, Alarmhys

Rosemount 5300 Series

Reference Manual

00809-0100-4530, Rev BA July 2009

Table J-1. Definitions of Analog

Input Function Block System

Parameters

Parameter	Index	Units	Description
	Number
ACK_OPTION	23	None	Used to set auto acknowledgment of alarms.
ALARM_HYS	24	Percent	The amount the alarm value must return within the alarm limit before the associated
			active alarm condition clears.
ALARM_SEL	38	None	Used to select the process alarm conditions that will cause the OUT_D parameter
			to be set.
ALARM_SUM	22	None	The summary alarm is used for all process alarms in the block. The cause of the
			alert is entered in the subcode field. The first alert to become active will set the
			Active status in the Status parameter. As soon as the Unreported status is cleared
			by the alert reporting task, another block alert may be reported without clearing the
			Active status, if the subcode has changed.
ALERT_KEY	04	None	The identification number of the plant unit. This information may be used in the host
			for sorting alarms, etc.
BLOCK_ALM	21	None	The block alarm is used for all configuration, hardware, connection failure or system
			problems in the block. The cause of the alert is entered in the subcode field. The
			first alert to become active will set the Active status in the Status parameter. As
			soon as the Unreported status is cleared by the alert reporting task, another block
			alert may be reported without clearing the Active status, if the subcode has
			changed.
BLOCK_ERR	06	None	This parameter reflects the error status associated with the hardware or software
			components associated with a block. It is a bit string, so that multiple errors may be
			shown.
CHANNEL	15	None	The CHANNEL value is used to select the measurement value. Refer to the
			appropriate device manual for information about the specific channels available in
			each device.
			You must configure the CHANNEL parameter before you can configure the
			XD_SCALE parameter.
FIELD_VAL	19	Percent	The value and status from the transducer block or from the simulated input when
			simulation is enabled.
GRANT_DENY	12	None	Options for controlling access of host computers and local control panels to
			operating, tuning, and alarm parameters of the block. Not used by device.
HI_ALM	34	None	The HI alarm data, which includes a value of the alarm, a timestamp of occurrence
			and the state of the alarm.
HI_HI_ALM	33	None	The HI HI alarm data, which includes a value of the alarm, a timestamp of
			occurrence and the state of the alarm.
HI_HI_LIM	26	EU of PV_SCALE	The setting for the alarm limit used to detect the HI HI alarm condition.
HI_HI_PRI	25	None	The priority of the HI HI alarm.
HI_LIM	28	EU of PV_SCALE	The setting for the alarm limit used to detect the HI alarm condition.
HI_PRI	27	None	The priority of the HI alarm.
IO_OPTS	13	None	Allows the selection of input/output options used to alter the PV. Low cutoff enabled
			is the only selectable option.
L_TYPE	16	None	Linearization type. Determines whether the field value is used directly (Direct) or is
			converted linearly (Indirect).
LO_ALM	35	None	The LO alarm data, which includes a value of the alarm, a timestamp of occurrence
			and the state of the alarm.
LO_LIM	30	EU of PV_SCALE	The setting for the alarm limit used to detect the LO alarm condition.
LO_LO_ALM	36	None	The LO LO alarm data, which includes a value of the alarm, a timestamp of
			occurrence and the state of the alarm.
LO_LO_LIM	32	EU of PV_SCALE	The setting for the alarm limit used to detect the LO LO alarm condition.
LO_LO_PRI	31	None	The priority of the LO LO alarm.

J-2