HP 30 30 Multi-function Input Terminal ‘P1’ Define, Multi-function Input Terminal ‘P2’ Define

Chapter 6 - Parameter Description [I/O]

	The following table shows the selection in I/O-48.								Setting Range		Description
									LCD	7-Seg
									Speed-L	0	Multi-step speed - Low
	Setting Range						Description
									Speed-M	1	Multi-step speed - Mid
	LCD			7-Seg
									Speed-H	2	Multi-step speed - High
	None			0		Continuous operating after loss of
						frequency reference.			XCEL-L	3	Multi-accel/decel - Low
									XCEL-M	4	Multi-accel/decel - Mid
	FreeRun			1		Inverter cuts off its output after
						determining loss of frequency reference.			XCEL-H	5	Multi-accel/decel - High
									Dc-brake	6	DC injection braking during stop
						Inverter stops by its Decel pattern and
	Stop			2		Decel time after determining loss of			2nd Func	7	Exchange to 2nd functions
						frequency reference.			Exchange	8	Exchange to commercial power line
									-Reserved-	9	Reserved for future use
	I/O-49 [Time out] sets the waiting time before determining								Up	10	Up drive
									Down	11	Down drive
	the loss of reference signal. Inverter waits to determine the
									3-Wire	12	3 wire operation
	loss of a reference signal until times out.
									Ext Trip-A	13	External trip A
									Ext Trip-B	14	External trip B
	☞ Note: I/O-48 and I/O-49 also apply when DRV-04 is set to								iTerm Clear	15	Used for PID control
	‘Keypad-1’ or ‘Keypad-2’ for determining the loss of								Open-loop	16	Exchange between PID mode and
											V/F mode
	command frequency.
									Main-drive	17	Exchange between Option and
											Inverter
Related Functions: DRV-04 [Frequency Mode]
									Analog hold	18	Hold the analog input signal
					I/O-02 [V1 Input Minimum Voltage]
									XCEL stop	19	Disable accel and decel
					I/O-07 [I Input Minimum Current]
									P Gain2	20	Used for PID control
					I/O-48 [Lost command]
									SEQ-L	21	Sequence operation - Low
					I/O-49 [Time out]
									SEQ-M	22	Sequence operation - Mid
									SEQ-H	23	Sequence operation - High
									Manual	24	Exchange between Sequence
	I/O-12: Multi-function Input Terminal ‘P1’ Define										operation and Manual operation
	I/O-13: Multi-function Input Terminal ‘P2’ Define								Go step	25	Triggering Sequence operation
	I/O-14: Multi-function Input Terminal ‘P3’ Define										(Auto-B)
									Hold step	26	Hold last step (Auto-A)
									Trv Off.Lo	27	Used for Traverse Operation
I/O►		P1 dedine
							12	0	Trv Off.Hi	28
12			Speed-L						Interlock1	29
									Interlock2	30	Used for MMC operation
Factory Default:					Speed-L			0
									Interlock3	31
									Interlock4	32
I/O►		P2 dedine					13	1	[Speed-L, Speed-M, Speed-H]
13			Speed-M						By setting P1, P2, P3 terminals to ‘Speed-L’, ‘Speed-M’
Factory Default:					Speed-M			1	and ‘Speed-H’ respectively, inverter can operate at the
									preset frequency set in DRV-05 ~ DRV-07 and I/O-20 ~
									I/O-24.
I/O►		P3 dedine					14	2
14			Speed-H						The step frequencies are determined by the combination of
Factory Default:					Speed-H			2	P1, P2 and P3 terminals as shown in the following table.

Multi-function input terminals can be defined for many different applications. The following table shows the various definitions for them.

6-37