Parameter Description I/O Stop, INV line, Comm line, Run | HP 30 30

Chapter 6 - Parameter Description [I/O]

			[Stop]
	Related Functions: FU1-59	[Stall Prevention Mode]
			AXA-AXC is CLOED when the inverter is stopped.
	FU1-60	[Stall Prevention Level]

[OV]			[INV line, COMM line]
AXA-AXC is CLOSED when the DC link voltage is above			This function is used in conjunction with ‘Exchange’
the Over-voltage level.			function of multi-function input for commercial line
			exchange. To use both signal of ‘INV line’ and ‘COMM line’,
DC Link Voltage		OV Level (380V DC or 760V DC)	the optional Sub-A or Sub-C board must be installed.
		OV Level (380V DC or 760V DC)
			Output Frequency	Speed Search
			Output Frequency
		Time
AXA-AXC	ON	Time
		Time

[AXA-AXC configured as ‘OV’]

Time

FX-CM

[LV]

ON

Time

AXA-AXC is CLOSED when the DC link voltage is below

‘Exchange’-CM

ON

the Low-voltage level.

Time

AXA-AXC

DC Link Voltage

‘COMM line’

ON

Time

LV Level (200V DC or 400V DC)

Q1-EXTG

ON

ON

Time

‘INV line’

t1

t2

Inverter

Commercial

Inverter

Drive

Line Drive

Drive

Time

t1, t2: 50msec (interlock time)

AXA-AXC

ON

Time

[AXA-AXC configured as ‘COMM line’ and ‘Q1’ as INV line’]

[AXA-AXC configured as ‘LV’]

Related Functions:

I/O-12 ~ I/O-14 [Multi-function input]

[OH]

- [Exchange]

AXA-AXC is CLOSED when the heat sink of the inverter is

[Ssearch]

above the reference level.

[Lost Command]

AXA-AXC is CLOSED during the inverter is speed

searching.

AXA-AXC is CLOSED when frequency reference is lost.

[Step pulse]

Related Functions:

I/O-11 [Criteria for Analog Signal Loss]

When Auto (Sequence) operation is selected in I/O-50,

I/O-48 [Operating Method at Signal Loss]

AXA-AXC outputs pulse signals on every step.

I/O-49 [Waiting Time for Time Out]

[Run]

Related Functions:

I/O-50 ~ I/O-84 [Auto Operation]

AXA-AXC is CLOED when the inverter is running.

6-47

Image 139

HP 30 30 manual Parameter Description I/O Stop, INV line, Comm line, Ssearch, Lost Command, Run

Contents

30 HP 230/460V Safety Instructions Operating Precautions Page Page Page Contents Options Troubleshooting & Maintenance 460V Class 1 ~ 30HP 230V Class 1 ~ 30HP 460V Class 40 ~ 100HP Common Features Specification Iii Page 075 10 HP 550 75 HP InspectionEnvironmental Conditions Mounting Installation Other Precautions Frame Dimensions Blank Frame # 3 15 ~ 20 HP Frame # 4 25 ~ 30 HP Blank DB Resistor Basic Wiring230/460 50/60 Hz DC Bus Choke Symbols Functions Power Terminals N B1 B2 Installation Type a ConfigurationType B Configuration P N B1 B2 U Phase Power Input Dynamic Braking Unit Dynamic Braking Resistor DC Bus Choke Installation Type C Configuration Shorting terminals may cause internal damage to inverter Installation Wiring Power Terminals Wiring PrecautionsGrounding Power and Motor Connection B1 B2 U Phase Power Input Installation Wires and Terminal LugsMotor should be connected to the U, V, and W terminals JOG RST Type Symbol Name DescriptionControl Terminals 30A 30C 30B AXA AXC Control Circuit Terminal Installation Wiring Control Terminals Wiring PrecautionsExternal Sequence Inverter Circuitry Keypad Connector Installation Keypad Connection Installation Parameter LCD Keypad Segment Keypad Description Group Parameter Groups Operation LCD Keypad 00 Hz Operation LCD Keypad DisplayDisplays Description Operation Procedure for Setting Data LCD Keypad Drive Group FU1 Group FU2 Group Operation Parameter Navigation LCD Keypad Segment display Encoder knob 7-Segment KeypadParameter Group Description Second digit Operation 1 7-Segment Keypad DisplayDisplay Description First digit FUN2 Group FUN1 GroupI/O Group FU1 Group FU2 Group Operation Parameter Navigation 7-Segment Keypad Terminals Operation Method Function Function SettingOperation Method Keypad and Control Operation Page QUICK-START Procedures LCD Press Prog key Seg PressPROG/ENT key Operation using KeypadQuick-Start Procedures LCD Display Segment Display LCD Display Operation using Control Terminals2 W LCD Press ENT key Seg Press PROG/ENT key Operation using Keypad and Control Terminals00 STP 00Hz DRV Drive mode 03 Fx/Rx-1 Keypad DRV Freq mode Frequency set by External Source and Run/Stop by Keypad SegPress PROG/ENT key to save the data 00 STP 00HzDRV Cmd. freq 00 0.00Hz 00 60.00Hz LCD Press ENT key to save the dataPage Parameter Name Code Description Function SettingBasic function parameter setting Common parameter setting Auto-tuning of motor constant Function Settings F + PG controlSlip compensation Sensorless vector control Function Settings FU2-40 DescriptionFor V/F, Slip compen , SensorlessS, SensorlessT For VectorSPD, VectorT Advanced function 1 setting Function SettingsF control Parameter Name Code Description Parameters to view motor and inverter status Function Settings Sensorless vector controlStatus Code Description Vector control VectorSPD, VectorTRQ Starting / Accel/ Decel / Stopping pattern setting Protection & fault detection level setting Speed-H Speed-M Speed-L Advanced function 2 setting 1 PID operationSpeed Signal Applied speed value Jog and Multi-speed operation Energy-saving operation Function Settings Auto sequence operation Operation Examples WiringOperation condition Set it to 0 KeyPad DRV-5 Operation Example 2nd motor operation RST AXA Operation VectorSPD Control Example Operation Examples Drive Group DRV LCD keypad Parameter List Function 1 Group FU1 Pattern Limit HiFwd boost Rev boost FU1-99 Return Code Not available Function 2 Group FU2 Code Description Keypad Display Setting Range Units Factory Pole number Retry DelayAuto tuning SS blk time PID Out Dir SL P-gainSL I-gain PID Ref Para. Read DB modeRPM factor Version Input/Output Group I/O Out status P2 defineP3 define Status Segment Baud rate Relay modeAuto mode Inv No External Group EXT V2 filter V2 modeP5 define P6 define Pulse FeedBackPulse set Pulse num AM1 adjust LM modeLM adjust AM1 mode Communication Group COM Default Application Group APP App Mode Trv Off Lo Trv. AmpTrv. Scr Trv Off Hi AutoEx-intv AutoCh-Mode Sub-Board Selection Guide According To Function Parameter List Page Cmd. Freq 00 Hz Digital frequency settingMonitoring function setting Setting the DRV-04 Frequency or Torque Mode Acc. time DRV-01 Acceleration Time10.0 Parameter Description DRV DRV-02 Deceleration Time DRV-03 Drive Mode Run/Stop Method20.0 Setting Range Description Freq modeKeypad-1 10.00 DRV-05 ~ DRV-07 Step Frequency 1 ~ DRV-10 DC Link Voltage DRV-12 Fault DisplayDRV-08 Output Current DRV-09 Motor Speed DRV-15 Reference/Feedback Frequency Display LCD Keypad DRV-14 Command/Output Frequency Display LCD KeypadDRV-13 Motor Direction Set 7-Segment Keypad 130 Parameter Description DRV FU1-03 Run Prevention FU1-00 Jump to Desired Code #FU1-05 Acceleration Pattern FU1-06 Deceleration Pattern Decel FU1-07 Stop ModeFU1 Stop mode Decel Parameter description FU1 FU1 FU1 DcBr freq 00 HzFU1 DcBlk time 10 sec FU1 DcBr value 50 % FU1 PreExTime Sec FU1-14 Pre-excitation TimeFU1 DcSt value 50 % FU1 DcSt time Sec 00.0 FU1-15 Hold Time1000 FU1-16 Pre-excitation Current 60.00 Hz FU1 Freq limitFU1 F-limit Lo FU1 F-limit Hi FU1 V/F pattern Linear FU1-29 Volts/Hz Pattern 15.00 FU1-30 ~ FU1-37 User V/F Frequency and Voltage 150 FU1-38 Output Voltage Adjustment100 FU1-39 Energy Save Level FU1 Motor type Self-cool FU1-54 Overload Warning Level FU1-55 Overload Warning TimeFU1 ETH FU1 OL level 000 180 990 FU1-99 Return Code 7-Segment KeypadSt bit Page Parameter description FU1 FU2-04 Previous Fault History FU2-01 Previous Fault HistoryFU2-02 Previous Fault History FU2-03 Previous Fault History FU2-10 ~ FU2-16 Frequency Jump FU2-07 Dwell Frequency FU2-08 Dwell Time FU2-20 Power on Start Selection FU2-19 Input/Output Phase Loss Protection Bit SetFU2-19 Phase Loss Protection Select FU2Speed Search FU2-21 Restart After Fault Reset0000 RST restart FU2-22 Speed Search Select 75 kW FU2-28 Speed search hold timeFU2 SS blk time Sec FU2Motor select 75kW FU2-38 Carrier Frequency FU2Control mode FU2-39 Control mode selectionControl Detail Tuning Method for Sensorless Vector Control 171 FU2-40 ~ 44 Auto tuning29.03 FU2 SL P-gain 327632767 FU2-47 PID Operation Selection 30.0 300.0100.0 Parameter Description FU2 Process PID Control FU2-71 Accel/Decel Time Scale FU2-72 Power On DisplayFU2-69 Accel/Decel Change Frequency FU2-70 Reference Frequency for Accel/Decel FU2-76 Duty of DB Dynamic Braking Resistor FU2-75 DB Dynamic Braking Resistor Mode SelectionFU2-73 User display selection FU2-74 Gain for Motor Speed Display Parameter Upload Parameter Download FU2-79 Software VersionFU2-81 ~ FU2-90 2nd Motor Related Functions FU2-91 Parameter Read FU2-92 Parameter Write Para. init FU2-93 Parameter InitializeFU2-94 Parameter Write Protection FU2-99 Return Code 7-Segment Keypad Parameter Description FU2 Parameter description I/O 01 ~ I/O-05 Analog Voltage Input V1 Signal Adjustment06 ~ I/O-10 Analog Current Input I Signal Adjustment Input/Output Group I/O I/O-00 Jump to Desired Code # 20.00 11 Criteria for Analog Input Signal Loss Speed-L, Speed-M, Speed-H 12 Multi-function Input Terminal ‘P1’ Define13 Multi-function Input Terminal ‘P2’ Define 14 Multi-function Input Terminal ‘P3’ Define Accel/Decel Parameter XCEL-H XCEL-M XCEL-L, XCEL-M, XCEL-HParameter Speed-H Speed-M Speed-L Code Exchange Parameter Description I/O Dc-brakeUp, Down Analog hold Parameter Description I/O Wire ITerm ClearOpen-loop Main-drive Manual Xcel stop Hold stepGain2 SEQ-L, SEQ-M, SEQ-H 16 Terminal Output Status LCD Keypad DisplaySegment Keypad Display 15 Terminal Input Status 30.00 40 FM Frequency Meter Output 41 FM Adjustment21 ~ I/O-24 Step Frequency 4, 5, 6 40.00 Define AXA-AXC 42 FDT Frequency Detection Level43 FDT Bandwidth 44 Multi-function Auxiliary Contact Output FDT-4 FDT-1FDT-2 FDT-3 IOL FDT-5Stall Ssearch Lost CommandParameter Description I/O Stop INV line, Comm line 010 45 Fault Output Relay 30A, 30B, 30CMMC 9600 46 Inverter Number 47 Baud Rate Auto B Parameter Description I/O Auto-A Parameter Description I/O Parameter Description I/O EXT-01 Sub-Board Display EXT-00 Jump to Desired Code #Parameter Description EXT Signal Adjustment Sub-A, Sub-C EXT-05 V2 Mode Selection Sub-A, Sub-CEXT-06 ~ EXT-10 Analog Voltage Input EXT-14 Encoder Feedback Frequency EXT-12 Usage of Pulse Input Signal Sub-BEXT-15 Pulse Input Signal Selection Sub-B EXT-13 Real Motor Speed Direction EXT-22 ~ EXT-23 Gains for ‘Sub-B’ Board EXT-17 Filtering Time Constant for Pulse Input Signal Sub-BEXT-18 ~ EXT-21 Pulse Input Signal Adjustment Sub-B EXT-16 Encoder Pulse Number Sub-B EXT-24 Slip Frequency for ‘Sub-B’ Board EXT-34 LM Load Meter Output Sub-A EXT-35 LM Adjustment AM2 Adjust AM1 mode FrequencyAM1 Adjust AM2 mode DC link Vtg EXT-50~53 Speed limit for Torque mode operation Direction Torque DirSpeed limit Torque change Display Name EXT-56 Torque Detection LevelEXT-57 Torque Detection Bandwidth Parameter APP Jump code 001 APP-01 Application Mode SelectionApplication Group APP APP-00 Jump to desired code # Parameter Description APP ACti APP-02 Traverse AmplitudeAPP-03 Traverse Scramble Amplitude APP-04 Traverse Accel Time APP-05 Traverse Decel Time APP-09 Starting Auxiliary Motor Selection APP-06 Traverse Offset Hi SettingAPP-07 Traverse Offset Lo Setting APP-08 Running Auxiliary Motor Number Display 60.0 49.99APP-21 The Number of Aux. Motors 19.00 APP-25 Wake-Up Level ACtion APP-26 Auto Change Mode SelectionAPP-27 Auto Change Time APP-28 Auto Change Level 7200 APP-30 Actual Value Display APP-32 Draw Mode SelectionAPP-33 Draw Size Setting APP-29 Inter-Lock Selection Draw & Override Page Name Description Option Option Name Description Options SUB-A Sub-A board Board configuration Parameters of Sub-A Board Options Terminal ConfigurationVR V2 5G NC Q1 Q2 Q3 Extg NC P4 P5 P6 LM CM Terminal Description BOC Sub-B Board AOC BOC A+ A- B+ B- FBA FBB GND GND +5V +5V VCC VCC Options Terminal Configuration total 14 pinsParameters of Sub-B Board Sub-B board with Line Drive type encoder Sub-B board with Open collector type encoder + F Sub-C Board Isolated Parameters of Sub-C Board Q1 Extg NC P4 P5 P6 CM NC GND V2 AM1 AM2 VR GND AOC BOC Sub-D Board Code Description LCD display Options Parameters of Sub-D boardEncoder Pulse function Input/Output function GND Q1 Q2 Extg NC P4 P5 P6 CM NC V2 VR 5G NC NCAOC BOC Device-Net Field bus Remote cable Options 3 RS485 Communication Options Mounting the option boards Optional Keypads External options Options DB Resistors 130 600 DB Resistor RST JOG B1 B2 DB ResistorDB Unit Max distance 5m Short Wire should be Twisted ER-2 BR1000W085J 220 345 140 330 Type 1 Max Watt Type 2 Max Watt Type Options DB Dynamic Brake Unit Inverter Applicable motor rating DB Unit DimensionCM OH Dimension Power LED turns Red when input power is applied to DBU Suppressing the surge voltage on the inverter output side Rectifying the motor insulationPage Keypad Display Protective Description Fault DisplaySegment Function OPT Troubleshooting & Maintenance Protective Cause Remedy Fault Remedy Correctly Condition Check Point Troubleshooting Elements Test Polarity Measured Value How to Check Power Components Periodical Inspection MaintenancePrecautions Routine Inspection Megger test Parts Replacements Inspection Method Criterion Measuring Instrument Daily and Periodic Inspection ItemsPage Use Related Parameter Code Appendix a Functions Based on USE FU1 Group Application Parameter Code DRV GroupFU2 Group Application Parameter Code Appendix C Peripheral Devices SMC-50P Page EN 55011 CD 73/23/EEC and CD 89/336/EECEN50178 EN 50081-2 ENV 50140 EN 50178ENV 50204 Essential Requirements for CE Compliance EMC Installation Guide Viii Footprint Filters RFI Filters Footprint Standard for ACtionMaster Series Dimensions Revisions Cleveland Motion Controls