HP 30 30 manual Function 1 Group FU1

Chapter 5 - Parameter List

5.2 Function 1 Group [FU1]

		Keypad Display			Setting Range				Factory	Adj.
Code	Description							Units		During	Page
		LCD		7-Segment	LCD	7-Segment			Default
										Run
FU1-00	Jump to Desired Code #	Jump code		Not displayed	1 to 60	Not available		1	1	Yes	6-2
					None		0
FU1-03	Run Prevention	Run Prev.	03		Forward Prev		1	-	None	No	6-2
					Reverse Prev		2
					Linear		0
					S-curve		1
FU1-05	Acceleration Pattern	Acc. pattern	05		U-curve		2	-	Linear	No	6-2
					Minimum		3
					Optimum		4
					Linear		0
					S-curve		1
FU1-06	Deceleration Pattern	Dec. pattern	06		U-curve		2	-	Linear	No	6-2
					Minimum		3
					Optimum		4
					Decel		0
FU1-07	Stop Mode	Stop mode	07		DC-brake		1	-	Decel	No	6-2
					Free-run		2
FU1-0813	DC Injection Braking	DcBr freq	08		FU1-22 to 60 [Hz]			0.01	5.00 [Hz]	No
	Frequency
FU1-09	DC Injection Braking	DcBlk time	09		0 to 60 [sec]			0.01	0.1 [sec]	No
	On-delay Time
											6-2
FU1-10	DC Injection Braking	DcBr value	10		0 to 200 [%]			1	50 [%]	No
	Voltage
FU1-11	DC Injection Braking	DcBr time	11		0 to 60 [sec]			0.1	1.0 [sec]	No
	Time
FU1-12	Starting DC Injection	DcSt value	12		0 to 200 [%]			1	50 [%]	No
	Braking Voltage
											6-2
FU1-13	Starting DC Injection	DcSt time	13		0 to 60 [sec]			0.1	0.0 [sec]	No
	Braking Time
FU1-14	Pre-excitation Time	PreExTime	14		0 to 60 [sec]			0.1	1.0 [sec]	No	6-2
FU1-15	Hold Time	Hold Time	15		0 to 1000 [ms]			1	1000 [ms]	No	6-2
FU1-16	Pre-excitation Current	Flux Force	16		100 to 500 [%]			0.1	100.0 [%]	No	6-2
FU1-20	Maximum Frequency	Max freq	20		40 to 400 [Hz]			0.01	60.00 [Hz]	No
FU1-21	Base Frequency	Base freq	21		30 to FU1-20			0.01	60.00 [Hz]	No	6-2
FU1-22	Starting Frequency	Start freq	22		0.01 to 60 [Hz]			0.01	0.50 [Hz]	No
FU1-23	Frequency Limit selection	Freq limit	23		No		0	-	No	No	6-2
					Yes		1
FU1-2414	Low Limit Frequency	F-limit Lo	24		FU1-22 to FU1-25			0.01	0.50 [Hz]	No

13Code FU1-08 through FU1-11 appears only when FU1-07 is set to ‘DC-Brake’.

14Code FU1-24 through FU1-25 appears only when FU1-23 is set to ‘Yes’.

5-3