Lucent Technologies 7820-0802-003 manual Dsl

DS3-ATM physical interface, 14-2DS3-ATM port

physical-address,14-2

DSL

configuring nailed connections, 17-5configuring switched connections, 17-4data transfer rates, configuring, 17-6enabling only active ports, 17-4IDSL voice connections, 17-17incoming IDSL voice, 17-18

MAX TNT configuration for Plug and Play, 17-15modem rate control for, 17-9

outgoing IDSL voice, 17-18

per-session data transfer rates, configuring, 17-8Plug and Play, 17-12

Plug and Play BOOTP Relay configuration for, 17-15Plug and Play overview, 17-12

sample nailed PPP ADSL connection, 17-26DSL cards

authentication of calls, 17-4DSLPipe

configuring for ADSL, 17-28configuring for SDSL, 17-33,17-36default Plug and Play configuration, 17-14Plug and Play, 17-12

DSX cross-connect

configuring T3 card to connect to, 11-5configuring UDS3 card to connect to, 13-2specifying line length, 7-17

E

E1 channels

destination route for calls (deprecated), 9-16example configurations

nailed, 9-16

phone numbers, 9-14trunk groups, 9-14, 9-15

nailed group, explained, 9-4trunk groups, explained, 9-14usage, 9-4,9-14

E1 FrameLine card example configuration, 10-3Frame Relay and, 10-2overview, 10-1,10-2

PPP support, 10-2

routing protocols supported, 10-2SNMP and, 10-2

supported features, 10-1E1 line

configuration commands, data trunk, 18-11continuity check, two-wire,18-11

E1 lines

assigning name to profile, 9-6

CAS signaling modes, 9-8clock source and priority, 9-13configuration parameters, 9-5configuration requirements, 9-4configuring a back-to-back connection, 9-7configuring DPNSS signaling, 9-12configuring R1, 9-10

DASS 2 or DPNSS settings, 9-12default call route created by system, 9-16enabling, 9-7

example configurations DPNSS signaling, 9-12PRI, 9-7,9-8,9-9

R2 signaling, 9-11framing, 9-7

how system chooses a clock source, 9-13overlap receiving on, 9-13

overview, 9-2

overview of configuration, 9-2R2 signaling, 9-10signaling mode, 9-8

signaling system 7 (SS7) data trunks, 18-10specifying channel usage, 9-14specifying ISDN PRI signaling for, 9-12specifying signaling, 9-8

switch type, 9-8,9-12two-wire continuity check, 18-11type of front-end transceiver, 9-13type of transceiver, 9-4,9-13unchannelized, 9-2

E1 profile

assigning a name to, 9-6created by system, 9-5created for E1 card, 9-5example configurations DPNSS signaling, 9-12

E1/PRI, 9-7ISDN service, 9-8nailed channels, 9-16

phone number assignments, 9-14PRI, 9-7, 9-8, 9-9

R2 signaling, 9-11

trunk group assignments, 9-15using trunk groups, 9-14

name displayed in Line Status window, 9-7parameters in, 9-5

setting parameters, 18-10

enable/disable

cell payload parameter, DS3-ATM interface, 14-3DS3-ATM interface, 14-2

enable/disable parameter OC3-ATM interface, 15-2

enable/disable, OC3-ATM loopback parameters, 15-2

encoding

specifying analog for system codecs, 7-22,9-16used on T1 lines, 7-8

Index-4 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide