I

IAM. See initial address message (IAM) ICD. See Internet Call Diversion (ICD)

ICMP redirects, configuring system to ignore, 1-9Idle mode for T1 lines, 7-5,7-22

IDSL

incoming voice calls, 17-18outgoing voice calls, 17-18supported CPE devices, 17-4

voice connections, configuring, 17-17 See also DSL

IDSL card

configuring static route to gateway, 17-25connectors, 17-2

emulates 5ESS switch, 17-21,17-25features, 17-2

overview, 17-1

remote devices it supports, 17-1sample configuration, 17-22

sample configuration for Pipeline, 17-21,17-25signaling used, 17-1

switch type to use for remote device, 17-21,17-25transmission speeds and distances, 17-1

IDSL profile, sample configuration, 17-24inactivity timer, for DSL, 17-4

Inband signaling, call control, 7-11 Internet call diversion (data). See data

IP

E1 FrameLine card and routing, 10-2FrameLine card and routing, 8-2soft interface address, 2-5

IP address

assigning system, 1-4

requiring caller to accept dynamic, 1-9verifying with Ping, 1-7

IP interfaces, multiple per Ethernet port, 4-3 IPDC. See IP Device Control (IPDC) IP-Interface profile, assigning, 2-4IP-Interface profile, described, 4-3IP-Route profile, name of default, 1-6

ISDN

call-type used to route calls, 19-13configuring multiple NFAS groups, 7-13configuring single NFAS group, 7-13data sense, 7-22

example NFAS configuration, 7-13example PRI configuration, 7-8,9-8,9-9signaling, 9-8

subaddress used to route calls, 19-12ISDN D channel

inverting data on, 7-22

sharing signaling among T1 lines, 7-13

specifying idle pattern, 7-22

ISDN PRI overview, 7-2,9-2

setting channel 24 as D channel, 7-8specifying for E1 lines, 9-12specifying signaling for T1 lines, 7-8

ISDN TAs, connecting via IDSL, 17-4

ITU-T. See International Telecommunications Union Telecommunication Standardization Sector (ITU-T)

L

LAN IP interfaces

directed broadcasts, disabling, 1-9leased connections

example channel configuration, 7-21,9-16example T1 channel configuration, 7-21nailed group for E1 channels, 9-4

nailed group for T1 channels, 7-5leased line

channels must be contiguous, 7-21,9-15configuring, 7-21,9-15

line speeds, configuring DSL, 17-6Line Status

E1 profile name displayed in, 9-7

T1 profile name displayed in, 7-7lines

enabling E1, 9-7

enabling serial WAN, 12-4enabling T1, 7-8enabling T3, 11-5enabling UDS3, 13-2SNMP support for T1, 11-1

line-side T1

call control, 7-11described, 7-2

List command, using, 7-6log level

setting, 1-5setting system, 1-5

log messages fan tray, 3-3

long haul transceiver, described, 9-13loopback parameter

enable/disable, OC3-ATM,15-2

M

management, shelf controller Ethernet port for, 1-4mark pattern, described, 7-22

master clock source, specifying, 7-17

Index-6

APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide

Page 236
Image 236
Lucent Technologies 7820-0802-003 manual Idsl