Lucent Technologies 7820-0802-003 manual Dns

serial WAN card configuration requirements, 12-2setting date and time, 1-5

setting log level, 1-5shelf-controller redundancy, 2-1,2-6signaling interface parameters, 18-5signaling system 7 (SS7) gateway, 18-4specifying default gateway, 1-6specifying digital modem negotiation, 5-2specifying DNS information, 1-6specifying IP address of shelf controller, 1-4specifying name, 1-5

T1 data trunk for signaling system 7 (SS7) data, example, 18-9

T1 lines, signaling system 7 (SS7) data trunks, 18-8T1 parameters ignored for T3, 11-3

T1 PRI, 7-8

T3 card for signaling system 7 (SS7) data, example, 18-9

T3 requirements, 11-2thermal controls, example, 3-2transport-layer options, 18-6understanding E1 requirements, 9-4using the command line interface, 7-6

Connection profiles

configuring to use nailed channels, 7-21,9-16sample for IDSL connection, 17-19,17-23

connections back-to-back T1, 7-21

configuring DSLPipe for ADSL, 17-28configuring DSLPipe for SDSL, 17-33,17-36DSL Plug and Play, 17-12

nailed DSL, 17-5

nailed group used for ADSL, 17-27sample nailed PPP over ADSL, 17-26serial WAN card support, 12-2

switch type for remote device in IDSL configuration, 17-21,17-25

switched DSL, 17-4continuity testing, 18-4control protocol

signaling system 7 (SS7), 18-6controller status

viewing, 2-10

CSU

specifying build-out,7-17 See also Front-end

D

Dchannel

inverting data on, 7-22sharing among PRI lines, 7-13specifying channel for PRI signaling, 7-8specifying idle pattern, 7-22

DASS-2

configuring back-to-back connection, 9-7required settings, 9-12

data sense (T1), 7-22data transfer

configuring ADSL rates, 17-6per-session rate, configuring, 17-8rates for ADSL-CAP,17-2

rates for ADSL-DMT,17-2rates for IDSL, 17-1

rates for SDSL, 17-3rates for SDSL-HS,17-3

rates optimized by RADSL, 17-2SDSL rates, configuring, 17-7

date and time, setting system, 1-5 DDL. See data delivery layer (DDL) default gateway, assigning system, 1-6defining soft IP interface for fault tolerance, 2-5denial of service attack, protecting system from, 1-9DHCP, server requirement for DSL Plug and Play, 17-13diagnostics, specifying messages to display, 1-5dialed digits, do not forward to system, 7-11

digital milliwatt (DMW) tone support on T3

digital millwatt tone (DMW) T1 support, 18-13

T3 support, 18-13

Dir command, using, 7-6,9-5directed broadcasts, disabling, 1-9disconnect cause codes, 18-21DLCIs

number supported on E1 FrameLine card, 10-2number supported on T1 FrameLine card, 8-2

DMW. See digital milliwatt (DMW)

DNS

adding system to, 1-4configuring basic, 1-6

DPC. See destination point code (DPC)

DPNSS

configuring back-to-back connection, 9-7example, 9-12

required settings, 9-12

DS3. See T3; DS3-ATM;STM-0DS3-ATM

framing formats, 14-2parameters, 14-1

DS3-ATM card

connecting redundantly to the WAN, 14-3DS3-ATM configuration, example, 14-3DS3-ATM interface

cell payload parameter, 14-3enable/disable parameter, 14-2

APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Index-3