APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Index-11
usage, 7-4, 7-18
T1 line
continuity check, two-wire, 18-11
T1 lines
assigning name to profile, 7-7
call control for, 7-11
call control for line-side, 7-11
call control for trunk-side, 7-11
clock source and priority, 7-4, 7-17
clocking for, 7-17
configuration, 18-8
configuration parameters, 7-6
configuring channelized, 7-11
configuring NFAS signaling for, 7-13
CSU or DSX, 7-17
data sense (PRI), 7-22
default call route created by system, 11-3
enabling, 7-8
encoding, 7-8
example configurations, 7-23
ISDN NFAS, 7-13
PRI, 7-8
FrameLine cards and, 8-1, 10-1
framing, 7-8
how system chooses a clock source, 7-17
idle-mode, 7-5, 7-22
inband signaling, 7-11
inverting data, 7-22
line-side vs. trunk-side, 7-2
overview, 7-2
overview of configuration, 7-3
provisioning switch for, A-1
R1 and R1-modified signaling, configuring, 7-15
robbed-bit call control, 7-11
signaling system 7 (SS7) data trunks, 18-8
SNMP support for, 11-1
specifying channel usage, 7-18
specifying D channel for PRI signaling, 7-8
specifying idle pattern, 7-22
specifying signaling, 7-8
specifying switch type for ISDN PRI service, 7-8
switch type, 7-8
T3 card and, 11-1
two-wire continuity check, 18-11
type of transceiver, 7-4, 7-17
unchannelized, 7-2
T1 network
signaling gateway, signaling system 7 (SS7), 18-4
T1 profile, 7-7
assigning a name to, 7-7
continuity checks, 18-12
created by system, 4-2, 7-6, 12-3
created for T1 card, 7-6
example configurations
ISDN NFAS, 7-13
nailed, 7-21
nailed channels, 7-21
phone number assignments, 7-19
PRI, 7-8
trunk group assignments, 7-20
inband signaling, 7-11
parameters in, 7-6
profiles not used by FrameLine card, 8-2
T2
outgoing continuity test, 18-13
T3 card
Call-Route profile and, 11-3
clocking, 11-5
configuration requirements, 11-2
configuring physical link, 11-5
enabling line, 11-5
FDL supported, 11-3
NFAS, 11-2
overview, 11-1
overview of configuration, 11-1
profiles created on start up, 11-3
SNMP management of, 11-1
T1 lines and, 11-1
T1 parameters ignored, 11-3
T1 profiles, 11-4
T3 network
signaling gateway, signaling system 7 (SS7), 18-4
T3 profile
assigning a name to, 11-4
described, 11-3
T5 timer
signaling system 7 (SS7), 18-11
TAOS , 18-4
continuity testing, supports, 18-13
TCP/IP
signaling gateway, 18-4
TDM. See time-division multiplexing (TDM)
Telnet, assigning password for access, 1-8
termination
calls, 18-21
testing
continuity, 18-4
TFTP, server requirement for DSL Plug and Play, 17-14
Thermal alarms, 3-3
Thermal profile, 3-1
overview for fan tray operations, 3-1
Thermal alarms, 3-3
Thermal profile, configuring for fan tray operations, 3-1
Thermal status command, 3-5
Thermal status reporting
fan tray, 3-4
time and date, setting, 1-5
tone-type and tone-sting
millwatt tones, analog, 18-13
traffic shaper, settings, 14-3, 15-3