11.OTHER PROGRAMMING

11.5 Alarm

2) With alarm output (option)

 

 

Operation screen

 

 

 

DISP

 

 

 

SHIFT

 

 

8

 

Ref. 1

[Output check]

ALARM

 

 

 

 

 

 

  

 

 

 

 

 

 

 

Relay No.

ENTRY

 

 

 

Ref. 2

[Programming check]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[To be ready for programming]

SET

 

 

 

 

 

END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cursor

1

 

to

4

 

 

 

 

 

 

 

 

[Programming alarm point]

CHART

 

SCALE

Ref. 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel

Level

 

 

 

 

 

 

 

 

/

 

 

%

°

[Selecting alarm type]

 

 

 

F

 

 

 

 

 

 

  

 

 

 

 

 

 

 

Alarm type

Numeric

 

 

 

 

 

 

 

 

 

 

 

 

Ref. 4

[Programming relay No.]

keys

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

Relay No.

Numeric

 

 

 

 

 

[Programming alarm value]

keys

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

Alarm value

 

 

 

 

 

[Only rate-of-change alarm]

°

 

Numeric

Ref. 5

F

 

 

keys

 

 

  

 

 

 

 

 

 

 

 

 

 

Measuring count

[Only differential alarm]

°F

 

keysNumeric

Ref. 6

 

 

 

 

 

 

  

 

 

 

 

When an error

 

ENTRY Channel to be compared

 

 

 

 

 

 

 

appears

Temporarily stored

 

 

 

 

 

press any key other

 

 

 

 

 

 

than

SHIFT

 

 

 

 

 

 

 

YES

 

Programming other alarm points?

 

 

 

 

 

 

 

 

 

 

 

 

NO

 

 

 

 

 

 

 

 

 

SHIFT

SET

 

 

 

 

 

 

 

 

END

 

 

 

 

Stored

 

 

Ref. 7

 

 

 

 

 

 

 

-66-

To delete alarm point

Follow the [Programming alarm point] procedure and select the alarm point

to be deleted with

/ .

and CLEAR

Clear it by pressing

SHIFT

 

 

0

simultaneously and perform [temporarily stored] and [stored] operation.

Reference 1 Output check

The relay Nos. in alarm output are displayed. This will be blank unless all of the relays are operated.

Reference 2 Other alarm point check

By pressing

/ , the level

advances from 1 to 4 and the

channel advances to the next

channel and then the level of the next

channel advances. Press

%

for

reverse operation.

 

 

 

Reference 3 Programming alarm point

1. Channel can be selected also with

/

or

% .

2. Channel advances by pressing /

Then “FaiL” and “C.End” appear. If

these functions are selected, program relay Nos. only.

Reference 4 Relay No.

This is for specifying terminal Nos. for alarm output.

The relay No. for AH is displayed with 2 digits such as “00”. See Section 12.2.When programming “1” to “9”,

two entering methods of

1 to 9 or

 

01 to 09 are available. (

: space)

 

 

 

 

Reference 5

Cursor appears only for

 

rate-of-change alarm.

 

Programming range is 1 to 20.

 

 

 

 

Reference 6

Cursor appears only for

 

 

differential alarm.

 

Reference channel to be compared is programmed in 1 to 4. (The differential alarm cannot be selected in a 1-pen type recorder because no channel to be compared is existed.)

Reference 7 Storing

Store the [temporarily stored] programmed values into the memory. (A programming change mark is printed.)

Page 70
Image 70
Omega RD200, RD2800 manual Other Programming