13. REMOTE CONTACTS

13.1 Remote Contacts Functions

ON: Short OFF: Open

Functions

Contact signal at terminal

Program messages first. See Section 11.10.

 

Message

 

COM

 

EX1

EX2*

 

 

(3) Execution of message printing

No.1

OFF

For trigger

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(No.1 and 2)

No.2

ON

 

 

 

 

 

 

 

 

1 sec. or more

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* When the trigger signals is sent (for 1 sec. or more) after selecting the message No., the printing of programmed message starts.

(Note) Program “Printing on/off” to on with a key operation in advance. Execution of message printing with key operation is also available. See section 9.4.

Turn on (for 1 second or more) the terminal No. which the digital data

printing is allocated.

 

 

 

 

(Note 1)

Program “Printing on/off” to on with a key operation in advance.

(4) Execution of digital data

Execution of message printing with key operation is also available.

printing

See Section 9.2.

 

 

 

 

(Note 2) During execution, retry of the

 

 

 

 

 

execution can be accepted just

 

 

 

 

 

 

 

 

 

 

once.

 

 

 

 

 

1 sec. or more

 

 

 

Turn on (for 1 sec. or more) the terminal No. which the printing of list 1, 2 or

(5) Execution of list printing

3 is allocated.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Note)

Program “Printing on/off” to on with a key

 

 

 

 

 

 

 

 

 

 

 

 

 

(List 1, 2, 3)

 

operation in advance. Execution

of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

message printing with key operation is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

also available. See Section 9.3.

 

 

 

 

1 sec. or more

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Programming of the operation record position is necessary.

 

See Section 13.4.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turn on (for 1 sec. or more) the terminal

 

 

 

 

ON time

 

 

 

 

 

 

 

 

 

 

(6) Execution of operation record

No. which the operation record (No. A to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D) is allocated. During ON time, the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(No. A to D)

recording position shifts to 5 mm to the

 

 

 

 

 

 

 

 

 

 

 

ON time

 

right from the programmed operation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

record position.

 

 

 

 

 

 

 

 

 

 

 

5 mm

 

 

 

 

 

 

 

 

 

 

 

(Note) Program “Printing on/off” to

Operation record position

 

on with a key operation in

 

(10 to 90%)

 

advance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Available

in “Totalization” (option). The

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(7) Reset of totallization

totalized value can be reset at an interval time

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

programmed. It can be reset with a contact

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

signal, too.

 

 

 

 

1 sec. or more

Warning

Contact signal to terminals

For the contact signal applied to the remote contacts terminals, use a switch or a relay driven at 30V AC or less or 60V DC or less or a manual contact for a very light load.

-88-

Page 92
Image 92
Omega RD200, RD2800 manual Remote Contacts Functions, Contact signal to terminals