7. PROGRAMMING

7.4 Programming Procedures

This section explains the basic programming parameters.

1 Basic of Programming Flow Chart

Programming is interrupted to return to the operation

screen at any programming stage by pressing

DISP

 

Operation screen

 

DISP

key before storing.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Measured value/clock/alarm)

 

Keys to be pressed depending on programming items.

 

 

 

 

 

 

 

 

 

3 sec. or

This action is necessary for some programming items.

 

 

 

 

 

 

 

 

more

 

 

 

 

 

 

 

 

 

Programmed parameter check

 

For parameters to be programmed for each channel,

 

 

 

SET

 

 

 

 

 

END

 

 

check the programmed parameters of other channels

 

Ready for programming

 

with

/

or

% .

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

keys

 

 

(1) Programming lamp lights.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Programming

 

 

(2) The cursor appears at a

 

 

 

 

 

 

programmable digit.

 

 

Cursor

 

 

by using numeric values or

 

 

 

 

 

parameters selection

 

 

 

 

 

 

 

 

 

 

YES

 

 

 

 

 

Character display

 

 

Programming lamp

 

Same programming for all

 

Character

display (Abbreviation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Memory colon

 

 

 

channels?

 

 

 

 

 

 

(Programming for

NO

ENTRY

 

 

 

 

 

of a programming item)

 

each channel)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Temporarily stored

 

 

If this procedure is omitted, programmed parameters

 

 

 

 

 

 

are not stored into memory.

 

 

 

 

 

Programming other channels?

YES

(Note) Common programmed parameters are

 

 

 

NO

 

 

Reference

stored only by pressing

ENTRY key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTRY (Note)

 

SHIFT

+

SET

(1) Memory colon starts blinking.

 

 

 

END

 

 

 

 

Stored

 

 

(2) Programming change mark

is printed.*

 

 

 

 

 

Programmed parameter (including temporarily

 

 

 

 

 

 

 

 

 

 

 

 

stored programmed parameters) are stored.

 

 

Programming same parameter to

During this storing operation, measurement is

Reference

interrupted.

 

 

 

 

 

other channels

 

 

* The change mark is printed on the right side of chart

 

 

 

Use [copy] function for convenient operation.

paper. However the

mark will not be printed

completely until the chart paper advances several

See Section 11. 14.

 

 

 

 

 

 

lines.

 

 

 

 

 

 

 

2

Key Operation

1)Numeric keys and cursor

Cursor shifts rightward when pressing numeric

keys (

0

to

9

and

).

CLEAR

LIST

(-)

Press

°F

or

°C

for moving the cursor.

 

 

 

 

 

2)How to add or delete a decimal point

To add the decimal point move the cursor to

 

 

 

 

and press CLOCK

. To delete the

 

decimal point, press COPY(=)

. (Numeric vallue is

 

 

 

 

SPACE

 

also deleted.)

 

3) Clearing a displayed programmed parameter

The programmed parameter is cleared by

pressing SHIFT and 0 simultaneously.

CLEAR

-37-

Page 41
Image 41
Omega RD2800, RD200 manual Programming Procedures, Basic of Programming Flow Chart