Omega RD200, RD2800 manual Input Specifications, Printing

22. SPECIFICATIONS

1 Input Specifications

Number of measuring points: 1, 2, 3 and 4 points

Input signals: DC voltage (mV) …±13.8, ±27.6, ±69.0, ±200

±500

DC voltage (V)…±2, ±5, ±10, ±20, ±50 (Built- in voltage divider for ±5 V or more)

DC current…Available by adding shunt resistor (option)

Thermocouple…B, R, S, K, E, J, T, N, NiMo-Ni, CR-AuFe, PtRh40-PtRh20

WRe5-WRe26, W-WRe26, Platinel II, U, L

Resistance thermometer…Pt100 (1),

Pt100 (2), JPt100, Pt50, Pt-Co Range: Program range number and printing range for each channel with key operation. (See Section 8.2 for

range No. list)

Scale: Program minimum and maximum values with key operation.

Programming range…-9999 to 99999 Decimal point … Program arbitrary

Measuring range: Refer to the list of range No. in Section 8-2.

Minimum printing range: Refer to the following table

	DC		1/5 or higher than the measuring range.
	voltage
			2/5 or higher than the measuring range when
	Thermo-		converted into electromotive force.
			(In the case of range Nos. with minus
	couple		measuring ranges, a temperature of 0°C or
			higher is specified as the lower-limit
			measuring value.)
	Resistance		Pt100		100°C span or more
	thermometer		Pt50		200°C span or more
	Accuracy rating: Refer to item			6	(at reference operating
			condition).
Temperature		drift: ±0.01% full			scale/°C (converted into

reference range)

Measuring cycle: About 100 msec (CH1 to CH4 )

Reference junction compensation: Inside (enable) or external (disable) is selectable.

Reference junction compensation accuracy:

K, E, J, T, N and Platinel II…±0.5°C or less Other than the above*… ±0.1°C or less *Except PtRh40-PtRh20

Input resolution: Approx. 1/56000 (converted into reference range)

Burnout: Effective input… Thermocouple, resistance thermometer

Programming range …Selection from up-scale, down-scale or disable for each channel

Allowable signal source resistance:

DC voltage inputs, thermocouple inputs

…1kΩ or less*

Resistance thermometer inputs

…10Ω or less

* Without burnout

Input resistance: Thermocouple input …About 8MΩ DC voltage inputs (range of ±2 V or less)

…About 8MΩ

DC voltage inputs (range of ±5 V or less) …About 1MΩ

Maximum input voltage

DC voltage	±10 V DC or less (range of ±2 V or less)
inputs,
	±60 V DC or less (range of ±5 V or less)
thermocouple
Resistance	±6 V DC or less
thermometer

Input correction: Shift programming for each channel

Input filter: Program primary delay filter

1 to 10 sec. and “0” (none) for each channel. Maximum common mode voltage: 30VAC

Common mode rejection ratio: 140 dB or more (50/60 Hz)

Series mode rejection ratio: 50 dB or more (50/60 Hz)

Terminal board: Detachable and removable for wiring

2 Printing

Printing accuracy: Measuring accuracy + ±.0.3% of printing range (under the reference operation condition)

Printing dead and: 0.2% of printing range

Printing system:

Trace printing… Disposable cartridge pen Digital data printing …. Plotter pen

Step response: RD200 … 1 sec. or less (90% response) RD2800 … 1.5 sec. or less (90% response)

Print color: Trace printing ….1st pen (Red), 2nd pen (Green),

3rd pen (Blue), 4th pen (Brown) Digital data printing … Purple

<<Digital printing>>

cPeriodic	: Printing of time, channel No., measured
data printing	values and engineering unit with
	programmed interval
dDigital data	: Printing of time, channel No., measured
printing	values and engineering unit with trace
eYear, Month,	printing on demand
	: Printing of year, month, day and time when
day, time, time	turning on the power. Printing time line and
line	time every on the hour. Printing year, moth
	and day at 00:00 and every specific interval
fChannel No.,	: Printing of scale, channel No. and tag (only if
scale, tag ﾞ	they are programmed) with every specific
	interval
gChart speed	: Printing of chart speed with every specific
	interval
hAlarm	: Printing of time, channel No., alarm type and
Activation/	alarm level when an alarm activates. Printing
Reset	time, channel No. and alarm level when the
	alarm is reset. Memory volume is max. 48
	data
iProgramming	: Marking when changed parameters are
change mark	stored
jPOC mark	: Marking when time-axis synchronization is
	programmed
kList printing	: Printing of parameters (list 1 or 2) on demand
	List 1: Chart speed, range/printing range,
	scale, subtract printing, periodic data
	printing, printing format and alarm
	List 2: Chart speed (3 speeds), alarm output,
	time-axis synchronization, remote
	contacts and math expression
	List 3: All parameters (List 1 + List 2)

－１２６－