Switching on the power supply, Checking the system | Siemens D410

Commissioning (hardware) 2.3 Switching on the power supply

2.3Switching on the power supply

Checking the system

Check the system installation and wiring once again before you switch it on. Observe the safety-relevant items of the following checklist:

●Have you observed all ESD measures when handling the components?

●Are all connectors properly inserted and interlocked / screwed on?

●Are all components grounded and all shields terminated?

●Have you made allowances for sufficient load capacity of the central power supply?

Switching on the external power supply

Power is supplied to the SIMOTION D410 using an external power supply unit, for example, using SITOP power supplies (in special circumstances, the SIMOTION D410 can also be supplied using the PM340 Power Module, see SIMOTION D410 Manual).

Switch on the power supply after having checked off all items of the checklist.

CAUTION

It is imperative to prevent the external 24 VDC power supply to SIMOTION D410 from being interrupted for a duration longer than 3 ms. Operation of SIMOTION D410 is stopped on expiration of these 3 ms and can only be recovered by cycling power Off > On.

Additional information is available in chapter "User memory concept".

Startup of SIMOTION D410

The startup of SIMOTION D410 is initiated after the power supply is activated:

1.The RDY LED is lit and the red RUN/STOP LED briefly lights up at the beginning of the startup sequence. These LEDs can be used to monitor the startup sequence. Any errors are displayed.

2.Startup of the SIMOTION kernel.

3.All DRIVE-CLiQ connections (with SINAMICS S120 Power Module PM340, for example) are identified automatically.

Note

Startup of SIMOTION D410 is completed as soon as its RDY LED is lit in green color and the RUN/STOP LED is lit in yellow or green color.

The SIMOTION D410 is ready for configuring after successful completion of the startup.

D410	33
Commissioning Manual, 08/2008 Edition

Image 33

Siemens D410 appendix Switching on the power supply, Checking the system, Switching on the external power supply

Contents

Commissioning Manual Simotion Safety Guidelines Contents of the commissioning manual Information blocks in this manualSimotion Documentation Europe / Africa Hotline and Internet addresses Technical supportPhone Fax Questions about this documentation Siemens Internet addressAdditional support Disposal and recycling Further information / FAQs Table of contents Table of contents 145 Page Overview System overviewApplication Product variants 7HFKQRORJ\ Ixqfwlrqv System integration Description 1.1 System overview Function System components Profibus DP Description System components Profinet DRIVE-CLiQ View Simotion D410 DP display Interfaces Simotion D410 nameplate Nameplates 3 23LQWHUIDFH Simotion D410 PN display Ports X200 Nameplates 3 Pre-installed runtime licenses CompactFlash cardCompactFlash card Available Z options / licenses for Simotion D CF cards LicensingSimotion D410 licensing Additional references Safety information Page Prerequisites for commissioning Connecting a programming device / PC to Simotion D410Prerequisites System requirements Procedure Inserting the Compact Flash cardProperties of the CF card Switching on the external power supply Switching on the power supplyChecking the system Startup of Simotion D410 Reset button Performing a reset operationArrangement User memory concept Simotion D410 memory modelSee also Properties of the user memories Non-volatile data ContentNon-volatile data Properties Meaning Ghylfh Volatile data Operator actions and their impact on user memory Download Simotion ScoutCopy RAM to ROM Backup of non-volatile data Entry Meaning To correct or avoid errors Diagnostics of non-volatile dataStartup and non-volatile data Situa Initial condition Result Tion Status Page Software requirements Inserting Simotion D410 into a projectSimotion Scout Engineering System Properties Ethernet Interface dialog box is open Image of a Simotion D410 PN in HW Config Representation in HW Config Configuring the Profibus DP interface only D410 DP General information about Profibus DP communicationDefinition of Profibus DP Assignment of the Profibus addresses in HW Config Assigning Profibus addressesRecommendation for Profibus addresses Operating Simotion D410 on Profibus DP Creating a new Profibus DP subnetProfibus DP interface Setting the DP cycle and system cycle clocks Rules for synchronizing the system clocks Rules for Simotion D410 DP Rules for Simotion D410 DP General information about Profinet communication Configuring Profinet only for D410 PN Profinet interfaces X200 Operating Simotion D410 PN on ProfinetProperties of Profinet on Simotion D410 PN LEDs Initializing Simotion D410 Changing the IP address, device name, network gateway Reading the IP address Setting the send cycles and system clocks Setting the DP cycle in HW ConfigPrerequisite Setting the send cycle in HW Config DP cycle / send cycle Servo cycle clockCycle Rules for Simotion D410 PN Rules for using the Profinet send cycle Rules for Simotion D410 PN Page Commissioning steps Overview of commissioning Configuring the system in offline mode Prerequisites for offline configurationOverview Integrated drive Accessing the drive wizard Drive properties Configuring the components Selecting a power unit Select a motor holding brake if installed Selecting a motor holding brake Selecting the Profibus message frame Finishing the drive 10 Configuration prior to HW Config alignment Aligning HW Config Downloading the project to Simotion D410 Procedure for downloading a project into the target system Procedure for downloading a created project to the CF card Configuring the system in online mode Prerequisites for online configurationIntroduction Establishing the online connection 12 Starting automatic configuration Starting automatic configuration Result 14 Automatic configuration completed Editing Sinamics components Download the project to Simotion D410 Creating an axis Creating an axis using the Axis Wizard Commissioning software Creating an axis Configuring tasks Configuring two encodersIntegrating additional encoders optional General information 18 Selecting the internal encoder interface Configure the encoder interface on the drive side Requirements Configuring a second encoder for a to axis in Simotion Encoder using PROFIBUS/PROFINET Configuring external encoders in Simotion Using drive-related I/Os by Simotion Onboard I/Os and terminal modules configuration overviewUsing Sinamics I/Os by Simotion Commissioning software Using drive-related I/Os by Simotion Use of message frame Message frame 39x configurationFunctionality of the 390, 391 and 392 message frames Concise Functionality available on the DI/DO of the D410 19 Message frame 39x configuration Input Output Use of the onboard I/O by Simotion 21 Configuring DI/DOs as input or output Configuring DI/DO as input or output Additional references Configuring free message frames by means of Bico Free message frame configuring using the TM31 as exampleMessage frames 22 Inserting a specific number of PSDs for the I/O data Configuring user-specific message frames 23 Reading the I/O address space 24 Selecting the PSD Interconnecting the message frame for TM31 Address Creating an I/O variable in Simotion 26 Profibus message frame Expanding a message frame Commissioning software Using drive-related I/Os by Simotion D410 Commissioning Manual, 08/2008 Edition Using high-speed outputs for output cams / DOs with D410 Using high-speed outputs for output cams on D410 Configuration of probe inputs Using probe inputs on D410Local and global measuring inputs Logical hardware address and bit number Output on the D410 Local measuring input Global measuring input Configuring of local measuring inputs on the D410 Configuring of global measuring inputs on the D410 Parameters in the expert list of the CUParameters in the expert list of the drive Quantity framework for TM15/TM17 High Feature Creating and programming TM41 Configuring TM41 at Sinamics Integrated 1 DMC20 hub properties Creating a DMC20DRIVE-CLiQ hub properties Application examples Creating a DRIVE-CLiQ hub Testing the drive using the drive control panel Testing the configured drive using the drive control panel 29 Assuming control priority Testing the configured axis using the axis control panel Axis control panelAxis test 32 Assuming control priority Downloading user data Downloading and saving user data Deleting data Overview of data deletionSaving user data Data deleted by memory reset Resetting the memory of Simotion D410 Data retained during memory reset Memory reset by means of Simotion ScoutMemory reset using the mode selector switch Deleting user data from the CompactFlash Card 33 Switch position Mres Restoring the default settings of Simotion D410 Restoring the default settings of Sinamics IntegratedRestoring the default settings Deleting user data System shutdown Restoring the default settings using the DIL switchPage Removing and replacing the Simotion D410 Replacing modules Close HW Config Replacing defective modules Replacing DRIVE-CLiQ components Replacing componentsAutomatic upgrading/downgrading Replacing the fan Replacing the fan Upgrading Simotion D410 Performing a software and firmware update 127 Re-compiling and downloading project data in Simotion Scout Replace the module in HW ConfigUpdating the firmware of the Sinamics components Upgrading a project Upgrading technology packages Download the project to the target system Upgrading the library Simotion CompactFlash Card Replacing the CompactFlash CardWriting and deleting data on CompactFlash Cards Saving technology and user data to the CompactFlash Card Formatting the CompactFlash Card Writing a bootloader Bootloader on the CompactFlash cardPage Symbol Meaning Diagnostics by means of LED displays LED displays Status Meaning OUT Extended diagnostic capabilities Diagnostic functions with the DIP switchSimotion Task Profiler application General rules Safety of electronic controllers ReliabilityRisk Important note Division into safety-critical and non-safety-critical areas Definition Electromagnetic CompatibilityRelevant standards regarding electromagnetic compatibility Informational topic Standard ESD definition Electrostatic charging of individualsWhat does ESD mean? Avoid direct contact Ensure sufficient grounding Abbreviation List of abbreviations Abbreviation Description Appendix List of abbreviations Index Index Profibus DP Index