Configuring the Profibus DP interface only D410 DP | Siemens

Configuring SIMOTION D410

3.3 Configuring the PROFIBUS DP interface (only D410 DP)

3.3Configuring the PROFIBUS DP interface (only D410 DP)

3.3.1General information about PROFIBUS DP communication

Definition of PROFIBUS DP

PROFIBUS DP is an international, open field bus standard specified in the European field bus Standard EN 50170 Part 2. PROFIBUS DP is optimized for high-speed, time-sensitive data transfer at field level.

Components communicating on PROFIBUS DP are classified as master and slave components.

●Master (active bus node)

Components representing a bus master determine the data traffic on the bus and are therefore also referred to as active bus nodes.

●Slaves (passive bus nodes)

These devices may only receive, acknowledge and return messages to the master if requested by the master.

Examples: SINAMICS drives, I/O modules

Note

If a SIMOTION D410 DP is operated as a passive PROFIBUS I-slave, the display, measuring functions and controller optimization engineering functions will be very slow. If possible, use the "active I-slave" setting for local commissioning (which does mean that an equidistance is no longer possible) and for complete commissioning, switch to "passive I- slave".

Additional references

You will find additional information about PROFIBUS DP in the SIMOTION Communication System Manual.

46	D410
	Commissioning Manual, 08/2008 Edition

Image 46

Siemens appendix Configuring the Profibus DP interface only D410 DP, General information about Profibus DP communication

Contents

Simotion Commissioning Manual Safety Guidelines Information blocks in this manual Contents of the commissioning manualSimotion Documentation Phone Hotline and Internet addresses Technical supportEurope / Africa Fax Siemens Internet address Questions about this documentationAdditional support Further information / FAQs Disposal and recycling Table of contents Table of contents 145 Page Application System overviewOverview Product variants System integration 7HFKQRORJ\ Ixqfwlrqv Description 1.1 System overview System components Function Profibus DP Description System components Profinet DRIVE-CLiQ Simotion D410 DP display View Interfaces Nameplates Simotion D410 nameplate 3 Simotion D410 PN display 23LQWHUIDFH Ports X200 Nameplates 3 CompactFlash card Pre-installed runtime licensesCompactFlash card Simotion D410 licensing LicensingAvailable Z options / licenses for Simotion D CF cards Additional references Safety information Page Prerequisites Connecting a programming device / PC to Simotion D410Prerequisites for commissioning System requirements Inserting the Compact Flash card ProcedureProperties of the CF card Checking the system Switching on the power supplySwitching on the external power supply Startup of Simotion D410 Performing a reset operation Reset buttonArrangement Simotion D410 memory model User memory conceptSee also Non-volatile data Non-volatile data ContentProperties of the user memories Properties Meaning Volatile data Ghylfh Download Simotion Scout Operator actions and their impact on user memoryCopy RAM to ROM Backup of non-volatile data Startup and non-volatile data Diagnostics of non-volatile dataEntry Meaning To correct or avoid errors Situa Initial condition Result Tion Status Page Inserting Simotion D410 into a project Software requirementsSimotion Scout Engineering System Properties Ethernet Interface dialog box is open Representation in HW Config Image of a Simotion D410 PN in HW Config General information about Profibus DP communication Configuring the Profibus DP interface only D410 DPDefinition of Profibus DP Assigning Profibus addresses Assignment of the Profibus addresses in HW ConfigRecommendation for Profibus addresses Creating a new Profibus DP subnet Operating Simotion D410 on Profibus DPProfibus DP interface Setting the DP cycle and system cycle clocks Rules for Simotion D410 DP Rules for synchronizing the system clocks Rules for Simotion D410 DP Configuring Profinet only for D410 PN General information about Profinet communication Properties of Profinet on Simotion D410 PN Operating Simotion D410 PN on ProfinetProfinet interfaces X200 LEDs Initializing Simotion D410 Reading the IP address Changing the IP address, device name, network gateway Setting the DP cycle in HW Config Setting the send cycles and system clocksPrerequisite DP cycle / send cycle Servo cycle clock Setting the send cycle in HW ConfigCycle Rules for using the Profinet send cycle Rules for Simotion D410 PN Rules for Simotion D410 PN Page Overview of commissioning Commissioning steps Prerequisites for offline configuration Configuring the system in offline modeOverview Accessing the drive wizard Integrated drive Configuring the components Drive properties Selecting a power unit Select a motor holding brake if installed Selecting a motor holding brake Selecting the Profibus message frame Finishing the drive Aligning HW Config 10 Configuration prior to HW Config alignment Procedure for downloading a project into the target system Downloading the project to Simotion D410 Procedure for downloading a created project to the CF card Prerequisites for online configuration Configuring the system in online modeIntroduction Establishing the online connection Starting automatic configuration 12 Starting automatic configuration 14 Automatic configuration completed Result Editing Sinamics components Download the project to Simotion D410 Creating an axis using the Axis Wizard Creating an axis Commissioning software Creating an axis Integrating additional encoders optional Configuring two encodersConfiguring tasks General information Configure the encoder interface on the drive side 18 Selecting the internal encoder interface Configuring a second encoder for a to axis in Simotion Requirements Configuring external encoders in Simotion Encoder using PROFIBUS/PROFINET Onboard I/Os and terminal modules configuration overview Using drive-related I/Os by SimotionUsing Sinamics I/Os by Simotion Commissioning software Using drive-related I/Os by Simotion Functionality of the 390, 391 and 392 message frames Message frame 39x configurationUse of message frame Concise Functionality available on the DI/DO of the D410 19 Message frame 39x configuration Use of the onboard I/O by Simotion Input Output Configuring DI/DO as input or output 21 Configuring DI/DOs as input or output Additional references Free message frame configuring using the TM31 as example Configuring free message frames by means of BicoMessage frames Configuring user-specific message frames 22 Inserting a specific number of PSDs for the I/O data 23 Reading the I/O address space Interconnecting the message frame for TM31 24 Selecting the PSD Creating an I/O variable in Simotion Address Expanding a message frame 26 Profibus message frame Commissioning software Using drive-related I/Os by Simotion D410 Commissioning Manual, 08/2008 Edition Using high-speed outputs for output cams on D410 Using high-speed outputs for output cams / DOs with D410 Local and global measuring inputs Using probe inputs on D410Configuration of probe inputs Logical hardware address and bit number Output on the D410 Local measuring input Global measuring input Configuring of local measuring inputs on the D410 Parameters in the expert list of the CU Configuring of global measuring inputs on the D410Parameters in the expert list of the drive Quantity framework for TM15/TM17 High Feature Configuring TM41 at Sinamics Integrated Creating and programming TM41 DRIVE-CLiQ hub properties Creating a DMC201 DMC20 hub properties Application examples Creating a DRIVE-CLiQ hub Testing the configured drive using the drive control panel Testing the drive using the drive control panel 29 Assuming control priority Axis control panel Testing the configured axis using the axis control panelAxis test 32 Assuming control priority Downloading and saving user data Downloading user data Overview of data deletion Deleting dataSaving user data Resetting the memory of Simotion D410 Data deleted by memory reset Memory reset by means of Simotion Scout Data retained during memory resetMemory reset using the mode selector switch 33 Switch position Mres Deleting user data from the CompactFlash Card Restoring the default settings Restoring the default settings of Sinamics IntegratedRestoring the default settings of Simotion D410 Deleting user data Restoring the default settings using the DIL switch System shutdownPage Replacing modules Removing and replacing the Simotion D410 Close HW Config Replacing defective modules Replacing components Replacing DRIVE-CLiQ componentsAutomatic upgrading/downgrading Replacing the fan Replacing the fan Performing a software and firmware update Upgrading Simotion D410 127 Updating the firmware of the Sinamics components Replace the module in HW ConfigRe-compiling and downloading project data in Simotion Scout Upgrading a project Upgrading technology packages Upgrading the library Download the project to the target system Replacing the CompactFlash Card Simotion CompactFlash CardWriting and deleting data on CompactFlash Cards Formatting the CompactFlash Card Saving technology and user data to the CompactFlash Card Bootloader on the CompactFlash card Writing a bootloaderPage Diagnostics by means of LED displays Symbol Meaning LED displays OUT Status Meaning Diagnostic functions with the DIP switch Extended diagnostic capabilitiesSimotion Task Profiler application General rules Reliability Safety of electronic controllersRisk Division into safety-critical and non-safety-critical areas Important note Relevant standards regarding electromagnetic compatibility Electromagnetic CompatibilityDefinition Informational topic Standard Electrostatic charging of individuals ESD definitionWhat does ESD mean? Ensure sufficient grounding Avoid direct contact List of abbreviations Abbreviation Appendix List of abbreviations Abbreviation Description Index Index Profibus DP Index