Manuals / Siemens / Computer Equipment / Network Hardware

Siemens D410 appendix Configuring the system in online mode, Introduction

Models: D410

1 150

Download 150 pages 59.82 Kb

Page 73

Commissioning (software) 4.3 Configuring the system in online mode

4.3Configuring the system in online mode

4.3.1Overview

Introduction

You can configure the plant in online mode after having completed its wiring. You can upload the data of SINAMICS components connected via DRIVE-CLiQ to your programming device

/PC using the "Automatic configuration" function. However, this functionality is only available within the initial commissioning phase.

Note

Components without DRIVE-CLiQ connection must be edited in offline mode. You may need to edit DRIVE-CLiQ components which were detected in the course of automatic configuration (for example, adding encoder data if using SMC modules).

Prerequisites for online configuration

●You created a project in SIMOTION SCOUT and added a SIMOTION D410 to the project.

●You configured the communication between the the programming device / PC and SIMOTION D410.

Procedure

Steps involved in offline configuring:

●Establishing the online connection

●Starting automatic configuration

●Configuring SINAMICS components

●Aligning HW Config

●Downloading the project to SIMOTION D410

D410	73
Commissioning Manual, 08/2008 Edition

Image 73

Siemens D410 appendix Configuring the system in online mode, Introduction, Prerequisites for online configuration

Contents

Commissioning Manual SimotionSafety Guidelines Information blocks in this manual Contents of the commissioning manualSimotion Documentation Europe / Africa Hotline and Internet addresses Technical supportPhone FaxSiemens Internet address Questions about this documentationAdditional support Disposal and recycling Further information / FAQsTable of contents Table of contents 145 Page Overview System overviewApplication Product variants7HFKQRORJ\ Ixqfwlrqv System integrationDescription 1.1 System overview Function System componentsProfibus DP Description System components Profinet DRIVE-CLiQ View Simotion D410 DP displayInterfaces Simotion D410 nameplate Nameplates3 23LQWHUIDFH Simotion D410 PN displayPorts X200 Nameplates 3 CompactFlash card Pre-installed runtime licensesCompactFlash card Available Z options / licenses for Simotion D CF cards LicensingSimotion D410 licensing Additional referencesSafety information Page Prerequisites for commissioning Connecting a programming device / PC to Simotion D410Prerequisites System requirementsInserting the Compact Flash card ProcedureProperties of the CF card Switching on the external power supply Switching on the power supplyChecking the system Startup of Simotion D410Performing a reset operation Reset buttonArrangement Simotion D410 memory model User memory conceptSee also Properties of the user memories Non-volatile data ContentNon-volatile data Properties MeaningGhylfh Volatile dataDownload Simotion Scout Operator actions and their impact on user memoryCopy RAM to ROM Backup of non-volatile data Entry Meaning To correct or avoid errors Diagnostics of non-volatile dataStartup and non-volatile data Situa Initial condition Result TionStatus Page Inserting Simotion D410 into a project Software requirementsSimotion Scout Engineering System Properties Ethernet Interface dialog box is open Image of a Simotion D410 PN in HW Config Representation in HW ConfigGeneral information about Profibus DP communication Configuring the Profibus DP interface only D410 DPDefinition of Profibus DP Assigning Profibus addresses Assignment of the Profibus addresses in HW ConfigRecommendation for Profibus addresses Creating a new Profibus DP subnet Operating Simotion D410 on Profibus DPProfibus DP interface Setting the DP cycle and system cycle clocks Rules for synchronizing the system clocks Rules for Simotion D410 DPRules for Simotion D410 DP General information about Profinet communication Configuring Profinet only for D410 PNProfinet interfaces X200 Operating Simotion D410 PN on ProfinetProperties of Profinet on Simotion D410 PN LEDsInitializing Simotion D410 Changing the IP address, device name, network gateway Reading the IP addressSetting the DP cycle in HW Config Setting the send cycles and system clocksPrerequisite DP cycle / send cycle Servo cycle clock Setting the send cycle in HW ConfigCycle Rules for Simotion D410 PN Rules for using the Profinet send cycleRules for Simotion D410 PN Page Commissioning steps Overview of commissioningPrerequisites for offline configuration Configuring the system in offline modeOverview Integrated drive Accessing the drive wizardDrive properties Configuring the componentsSelecting a power unit Select a motor holding brake if installed Selecting a motor holding brake Selecting the Profibus message frame Finishing the drive 10 Configuration prior to HW Config alignment Aligning HW ConfigDownloading the project to Simotion D410 Procedure for downloading a project into the target systemProcedure for downloading a created project to the CF card Prerequisites for online configuration Configuring the system in online modeIntroduction Establishing the online connection 12 Starting automatic configuration Starting automatic configurationResult 14 Automatic configuration completedEditing Sinamics components Download the project to Simotion D410 Creating an axis Creating an axis using the Axis WizardCommissioning software Creating an axis Configuring tasks Configuring two encodersIntegrating additional encoders optional General information18 Selecting the internal encoder interface Configure the encoder interface on the drive sideRequirements Configuring a second encoder for a to axis in SimotionEncoder using PROFIBUS/PROFINET Configuring external encoders in SimotionOnboard I/Os and terminal modules configuration overview Using drive-related I/Os by SimotionUsing Sinamics I/Os by Simotion Commissioning software Using drive-related I/Os by Simotion Use of message frame Message frame 39x configurationFunctionality of the 390, 391 and 392 message frames Concise Functionality available on the DI/DO of the D41019 Message frame 39x configuration Input Output Use of the onboard I/O by Simotion21 Configuring DI/DOs as input or output Configuring DI/DO as input or outputAdditional references Free message frame configuring using the TM31 as example Configuring free message frames by means of BicoMessage frames 22 Inserting a specific number of PSDs for the I/O data Configuring user-specific message frames23 Reading the I/O address space 24 Selecting the PSD Interconnecting the message frame for TM31Address Creating an I/O variable in Simotion26 Profibus message frame Expanding a message frameCommissioning software Using drive-related I/Os by Simotion D410 Commissioning Manual, 08/2008 Edition Using high-speed outputs for output cams / DOs with D410 Using high-speed outputs for output cams on D410Configuration of probe inputs Using probe inputs on D410Local and global measuring inputs Logical hardware address and bit number Output on the D410Local measuring input Global measuring input Configuring of local measuring inputs on the D410 Parameters in the expert list of the CU Configuring of global measuring inputs on the D410Parameters in the expert list of the drive Quantity framework for TM15/TM17 High Feature Creating and programming TM41 Configuring TM41 at Sinamics Integrated1 DMC20 hub properties Creating a DMC20DRIVE-CLiQ hub properties Application examplesCreating a DRIVE-CLiQ hub Testing the drive using the drive control panel Testing the configured drive using the drive control panel29 Assuming control priority Axis control panel Testing the configured axis using the axis control panelAxis test 32 Assuming control priority Downloading user data Downloading and saving user dataOverview of data deletion Deleting dataSaving user data Data deleted by memory reset Resetting the memory of Simotion D410Memory reset by means of Simotion Scout Data retained during memory resetMemory reset using the mode selector switch Deleting user data from the CompactFlash Card 33 Switch position MresRestoring the default settings of Simotion D410 Restoring the default settings of Sinamics IntegratedRestoring the default settings Deleting user dataSystem shutdown Restoring the default settings using the DIL switchPage Removing and replacing the Simotion D410 Replacing modulesClose HW Config Replacing defective modules Replacing components Replacing DRIVE-CLiQ componentsAutomatic upgrading/downgrading Replacing the fan Replacing the fanUpgrading Simotion D410 Performing a software and firmware update127 Re-compiling and downloading project data in Simotion Scout Replace the module in HW ConfigUpdating the firmware of the Sinamics components Upgrading a projectUpgrading technology packages Download the project to the target system Upgrading the libraryReplacing the CompactFlash Card Simotion CompactFlash CardWriting and deleting data on CompactFlash Cards Saving technology and user data to the CompactFlash Card Formatting the CompactFlash CardWriting a bootloader Bootloader on the CompactFlash cardPage Symbol Meaning Diagnostics by means of LED displaysLED displays Status Meaning OUTDiagnostic functions with the DIP switch Extended diagnostic capabilitiesSimotion Task Profiler application General rules Reliability Safety of electronic controllersRisk Important note Division into safety-critical and non-safety-critical areasDefinition Electromagnetic CompatibilityRelevant standards regarding electromagnetic compatibility Informational topic StandardElectrostatic charging of individuals ESD definitionWhat does ESD mean? Avoid direct contact Ensure sufficient groundingAbbreviation List of abbreviationsAbbreviation Description Appendix List of abbreviationsIndex Index Profibus DP Index