Chapter 18 DLPs F300 to F399

DLP- F392 Change Line Transmission Settings for STM-N Cards

 

 

 

 

Table 18-6

STM-N Card Line Settings (continued)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heading

 

Description

Options

 

 

 

 

 

 

 

 

 

 

 

 

 

Service State

 

Identifies the autonomously generated

Unlocked-enabled—The port is fully

 

 

 

 

 

 

state that gives the overall condition

 

operational and performing as

 

 

 

 

 

 

of the port. Service states appear in

 

provisioned.

 

 

 

 

 

 

the format: Primary State-Primary

Unlocked-disabled,automaticInService—

 

 

 

 

 

 

State Qualifier, Secondary State.

 

 

 

 

 

 

 

The port is out-of-service, but traffic is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

carried. Alarm reporting is suppressed.

 

 

 

 

 

 

 

 

The ONS node monitors the ports for an

 

 

 

 

 

 

 

 

error-free signal. After an error-free

 

 

 

 

 

 

 

 

signal is detected, the port stays in the

 

 

 

 

 

 

 

 

Unlocked-disabled,automaticInService

 

 

 

 

 

 

 

 

state for the duration of the soak period.

 

 

 

 

 

 

 

 

After the soak period ends, the port

 

 

 

 

 

 

 

 

service state changes to

 

 

 

 

 

 

 

 

Unlocked-enabled.

 

 

 

 

 

 

 

Locked-enabled,disabled—The port is

 

 

 

 

 

 

 

 

out-of-service and unable to carry

 

 

 

 

 

 

 

 

traffic.

 

 

 

 

 

 

 

Locked-enabled,maintenance—The port

 

 

 

 

 

 

 

 

is out-of-service for maintenance. Alarm

 

 

 

 

 

 

 

 

reporting is suppressed, but traffic is

 

 

 

 

 

 

 

 

carried and loopbacks are allowed.

 

 

 

 

 

 

 

 

 

 

 

 

 

SyncStatusMsg

 

Allows you to view the incoming

SETS

 

 

 

 

 

 

synchronization status message by

STU

 

 

 

 

 

 

clicking Show.

 

 

 

 

 

 

G811

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G812T

 

 

 

 

 

 

 

G812L

 

 

 

 

 

 

 

DUS_SDH (Do not use for timing

 

 

 

 

 

 

 

 

synchronization)

 

 

 

 

 

 

 

 

 

 

 

 

Reach

 

(ASAP card only) Provisions the

(The options that appear in the drop-down

 

 

 

 

 

 

reach value.

list depend on the card.)

 

 

 

 

 

 

 

Auto Provision—Allows the system to

 

 

 

 

 

 

 

 

automatically provision the reach from

 

 

 

 

 

 

 

 

the PPM reach value on the hardware.

 

 

 

 

 

 

 

SR—Short reach, up to 2 km distance

 

 

 

 

 

 

 

SR-1—Up to 2 km distance

 

 

 

 

 

 

 

IR-1—Intermediate reach, up to 15 km

 

 

 

 

 

 

 

 

distance

 

 

 

 

 

 

 

IR-2—Up to 40 km distance

 

 

 

 

 

 

 

LR-1—Long reach, up to 40 km

 

 

 

 

 

 

 

 

distance)

 

 

 

 

 

 

 

LR-2—Up to 80 km distance

 

 

 

 

 

 

 

LR-3—Up to 80 km distance

 

 

 

 

 

 

 

 

 

 

 

 

Cisco ONS 15600 SDH Procedure Guide, R8.0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18-110

 

 

 

 

 

 

October 2007

 

 

 

 

 

 

 

 

 

Page 110
Image 110
Cisco Systems ONS 15600 SDH manual Sets, Stu, 18-110