Manuals / HP / Computer Equipment / Printer

HP Enterprise CP5525 manual Tray X overfilled, Troubleshooting, Type mismatch Tray

Models: Enterprise CP5525

1 686

Download 686 pages 10.87 Kb

Page 512

If the error persists, use the Media size switches (SW2,3 - SW82,83 - SW92,93) test in the Tray/Bin manual sensor test to test the switches. If they do not respond, replace associated the lifter drive assembly.

Tray <X> overfilled

Description

The tray is filled above the stack-height mark.

◦X = 2 Tray 2

◦X = 3 Tray 3

◦X = 4 Tray 4

◦X = 5 Tray 5

◦X = 6 Tray 6

Recommended action

Remove enough paper so that the paper stack does not exceed the limit for the tray.

NOTE: If this message appears after lifter drive assembly was removed or replaced, make sure that the connector on the assembly is correctly connected and fully seated.

Troubleshooting

Description

The product is in the Troubleshooting process.

Recommended action

Press the Stop button .

To exit press

Type mismatch Tray <X>

Description

The specified tray contains a paper type that does not match the configured type.

488 Chapter 3 Solve problems

ENWW

Image 512

HP Enterprise CP5525 manual Tray X overfilled, Troubleshooting, Type mismatch Tray

Contents

HP Color Laserjet Enterprise CP5520 Page HP Color LaserJet Enterprise CP5520 Printer Series Copyright and License Trademark CreditsConventions used in this guide Conventions used in this guide Table of contents Enww Removal and replacement 101 Enww Solve problems 253 Enww 294 Xiii 414 Enww 459 Xvii 480 Xix Parts and diagrams 551 Appendix C Regulatory information 643 Appendix a Service and support 631Appendix B Product specifications 641 Index 655 Theory of operation Major product systems Product block diagramBasic operation Sequence of operation Normal sequence of operation1Sequence of operation Name Timing PurposePrint Sleep mode Formatter-control systemInput/output MemoryPJL overview FirmwarePML Control panelEngine-control system 2Engine-control system3DC controller diagram DC controller2Electrical components Component type Abbreviation NameEnww Motors MotorsMotors Description Components driven Failure DetectionFans Description Area cooled Type SpeedFuser-control circuit TH4 Fuser HeaterFuser temperature control 7Fuser-heater control circuitFuser protective function Fuser failure detection Low-voltage power supply SW1Enww Overcurrent/overvoltage protection High-voltage power supply 9High-voltage power supplyEnww Laser scanner system 10Laser/scanner systemLaser failure detection Image-formation system Electrophotographic process12Electrophotographic process drive system Image formation process 13Image formation processPrimary charging Latent-image formation blockPre-exposure Laser beam exposure 16Laser beam exposureDeveloping block 17 DevelopingSecondary transfer Transfer blockPrimary transfer Fusing block SeparationITB cleaning block Drum cleaning block24Print cartridge block diagram Print cartridgesMemory tag Cartridge presence detectionToner level detection Cartridge life detection25Developing unit engagement and disengagement control ITB unit ITBPrimary transfer roller engagement and disengagement control ITB cleaning mechanism ITB unit presence detectionCalibration SW6 ITBColor-misregistration control 29Color-misregistration controlEnvironment change control Image stabilization controlImage density control Dmax Image halftone control DhalfPickup, feed, and delivery system 30Pickup, feed, and delivery system31Pickup, feed, and delivery system blocks Description Photo sensors and switches productPhoto sensors 6Motors and solenoids paper path Motors and solenoidsPickup and feed block Tray 2 cassette pickup 34Tray 2 cassette pickup operationTray 2 cassette multiple-feed prevention 35Tray 2 cassette multiple-feed preventionEnww Tray 2 cassette lift-up operation 36Tary 2 cassette lift-up operation Tray 1 MP tray paper pickup Cassette media-presence detectionTray 1 MP tray last-paper detection SL2Paper feed 39Tray 1 MP tray last-paper detection40 Paper feed Skew-feed prevention 41Skew-feed preventionMedia detection Media detection sensor typesFusing and delivery block Auto Sense mode Print mode Media Speed Sensor DetectionFeed-speed control Loop control42 Loop control Pressure roller pressurization and depressurization control Output bin full detection 44Output bin full detectionDuplex block duplex models only Duplex reverse and duplex feed controlDuplex operation SL3Paper size Duplexing media feed mode Print mode Duplex printPaper sizes, duplex operation Print modes, duplex operationJam detection Product detects the following jamsAfter the TOP sensor detects the trailing edge Paper feeder 48Paper-feeder paper pathMotor Driving part Failure detection Paper-feeder motors10Paper-feeder motors Component type Abbreviation Description Paper-feeder paper pickup and feed11Paper-feeder electrical components Paper-feeder cassette lift operation Paper-feeder jam detection SR3Optional 3X500-sheet paper deck 543X500-sheet paper deck3X500-sheet paper deck Component Description133X500-sheet paper deck Component Component driven Failure Detection Motor control14Paper deck motors 15Pickup-and-feed operation Component SignalPickup-and-feed operation Paper Deck Cassette 3 Pickup Motor Control Cassette lift-up operation 58Cassette lift-up operation 59Jam detection Enww Removal and replacement Electrostatic discharge Removal and replacement strategyIntroduction Required tools 1Phillips and pozidrive screwdriver comparisonService approach Before performing serviceAfter performing service Post-service testRemoval and replacement procedures Replace print cartridgesEnww Enww Close the front door Removal and replacement Toner-collection unit 3Remove the toner-collection unit 2Enww Fuser Reset the New Fuser Kit setting at the control panelAdministration Manage Supplies Reset Supplies New Fuser Kit 7Remove the pickup roller Tray 1 2 Removal and replacement Pickup roller TraySeparation pad Tray Insert the tool under the separation pad Separation roller assembly Tray 13Remove the separation roller assembly Tray 2 2Open Tray Open the right-door assembly 15Remove the 1 x 500 or 3 x 500 rollers 1 Enww Secondary transfer roller Intermediate transfer belt ITB Enww Reset the New Transfer Kit setting at the control panel Formatter PCA 21Remove the formatter 1Enww Identify the hard drive type Hard DriveBefore proceeding, remove the following components Remove the encrypted HDD Remove the solid-state hard drive 26Remove the solid-state hard drive 1Remove the lock from the PCA External panels, covers, and doors CoversIdentification and location 1External panels, covers, and doors Right-front cover and control-panel assembly 31Remove the right-front cover and control-panel assembly 2Enww Left cover Rear cover Remove the rear coverToner collection unit access door 36Remove the toner collection unit access door 2Enww Right-rear cover 38Remove the right-rear coverReinstall the right-rear cover 39Right-rear cover ground spring Removal and replacementTop cover Remove the top coverEnww Front-door assembly 42Remove the front-door assembly 144Remove the front-door assembly 3 Removal and replacement 45Remove the front-door assembly 4 Right-door assembly 46Remove the right-door assembly 1 Removal and replacement48Remove the right-door assembly 3 Disconnect two connectors callout 51Remove the right-door assembly 6 Remove the formatter case Main assembliesFormatter case 53Remove the formatter case assembly 2 Laser/scanner assembly Remove the laser/scanner assembly56Remove the laser/scanner assembly 3 Enww Paper pickup assembly Remove the paper pickup assemblyDisconnect four connectors callout 61Remove the paper pickup assembly 4 Reinstall the paper pickup assembly 63Paper pickup assembly sensor flag correctly installed Installing a replacement paper pickup assembly Reset the New Registration Roller menu itemDevice Maintenance Service Service Access Code Reset the Media Sensor ValueEnww Registration sensor assembly Remove the registration sensor assemblyEnww Enww Lifter-drive assembly Remove the lifter-drive assemblyEnww Enww ITB front guide assembly 75Remove the ITB front guide assembly 3 Enww ITB rear guide assembly 77Remove the ITB rear guide assemblyResidual toner full sensor Remove the residual toner full sensor79Remove the residual toner full sensor 2 80Remove the residual toner full sensor 3 Reinstall the residual toner full sensor Enww Main drive assembly Remove the main drive assembly87Remove the main drive assembly 3 Removal and replacement 89Remove the main drive assembly 5 90Remove the main drive assembly 6 Removal and replacement 92Remove the main drive assembly 8 94Remove the main drive assembly 10 Removal and replacement 96Remove the main drive assembly 12 98Remove the main drive assembly 14 Removal and replacement 100Remove the main drive assembly 16 101Remove the main drive assembly 17 Removal and replacement Install the main drive assembly 102Install the main drive assembly 1104Install the main drive assembly 3 Removal and replacement See -103 Install the main drive assembly 2 of 8 on 108Install the main drive assembly 7 Removal and replacement 109Install the main drive assembly 8 Fuser drive assembly Remove the fuser drive assemblyDisconnect two connectors callout Install a replacement fuser drive assembly Original fuser drive assembly Proceed to the next stepEnww Fuser gear assembly Remove the fuser gear assembly118Remove the fuser gear assembly 3 120Remove the fuser gear assembly 5 Removal and replacement 122Remove the fuser gear assembly 7 Enww 124Remove the fuser gear assembly 9 Install a replacement fuser gear assembly Original fuser gear assembly Proceed to the next stepEnww Paper delivery assembly Remove the delivery assembly129Remove the paper delivery assembly 2 Reinstall the paper delivery assemblyEnww Duplex drive assembly duplex models Remove the duplex-drive assemblyRemove three screws callout Delivery drive assembly simplex models Remove the delivery drive assemblyResidual-toner-feed assembly Remove the residual-toner-feed assembly138Remove the residual-toner-feed assembly 2 ITB motor M1 Remove the ITB motor140Remove the ITB motor 2 Drum motor M2 Remove the drum motorDeveloping motor M3 Remove the developing motorFuser motor M4 Remove the fuser motorDeveloping-disengagement motor M6 Remove the developing-disengagement motorPower-supply fan FM1 Remove the power-supply fanEnww Enww Fuser fan FM2 Remove the fuser fan150Remove the fuser fan 3 Removal and replacement Enww Formatter fan FM3 and ICB PCA Remove the formatter fan and ICB PCA154Remove the formatter fan 3 Enww DC controller PCA Remove the DC controller PCAEnww Remove the low-voltage power supply Enww 162Remove the low-voltage power supply 3 Enww Imaging developing high-voltage power supply Remove the imaging developing high-voltage power supplyFirst transfer high-voltage power supply Remove the first transfer high-voltage power supply166Reinstall the first transfer high-voltage power supply Second transfer high-voltage power supply Remove the second transfer high-voltage power supply168Remove the second transfer high-voltage power supply 2 Driver PCA Remove the driver PCA170Remove the driver PCA 2 Power switch PCA Remove the power switch PCAEnvironmental sensor Remove the environmental sensor500-sheet paper feeder assembly 500 rear cover500 left cover 175Remove the 1 x 500 left cover 2Enww 500 right-front cover 500 front-upper cover 500 right door 180Remove the 1 x 500 right door 3 Removal and replacement 500 right-lower cover 181Remove the 1 x 500 right-lower cover500 pickup assembly 184Remove the 1 x 500 pickup assembly 3 Enww 500 lifter-drive assembly 187Remove the 1 x 500 lifter-drive assembly 2188Remove the 1 x 500 pickup motor Removal and replacement 500 pickup motor500 driver PCA 189Remove the 1 x 500 driver PCA500-sheet paper feeder optional accessory 190Remove the 3 x 500 rear cover Removal and replacement500 right and left cassette rails 191Remove the 3 x 500 right and left cassette rails500 paper deck controller PCAs 500 paper deck lifter-drive assembly 194Remove the 3 x 500 paper deck lifter-drive assembly 2500 paper deck pickup motor 500 front-lower cover 196Remove the 3 x 500 front-lower cover500 left cover 500 right-corner cover 199Remove the 3 x 500 right-corner cover500 front-upper cover 500 right-door assembly Enww 204Remove the 3 x 500 right-lower cover 500 right-lower cover 500 left-lower cover 500 rear-lower cover Remove the 3 x 500 rear-lower cover500 paper deck pickup assembly Remove the 3 x 500 paper deck pickup assemblyEnww Solve problems Solve problems checklist Solve problems checklist Current settings pages Administration Reports Configuration/Status PagesPrint the current settings pages Menu mapControl panel menus Sign In menuRetrieve Job From USB menu Retrieve Job From Device Memory menu4Supplies menu Supplies menu3Retrieve Job From Device Memory menu Enww Trays menu Trays menuAdministration menu General Settings menu7General Settings menu Reports menuEnww Enww Enww Enww Retrieve From USB Settings menu Print Settings menu8Retrieve From USB Settings menu Print Settings menu9Print Settings menu Print Options menu10Print Options menu Product supportsEnww Display Settings menu Display Settings menuManage Supplies menu 12Manage Supplies menuManage Trays menu 13Manage Trays menu15Embedded Jetdirect Network Settings menu14Network Settings menu Embedded Jetdirect KeepFirst level Troubleshooting menu 16Troubleshooting menuDevice Maintenance menu Backup/Restore menuCalibration/Cleaning menu USB Firmware Upgrade menu17Backup/Restore menu Calibration/Cleaning menuService menu Automatic Calibrations Disabled EnabledTroubleshooting process Determine the problem sourcePre-troubleshooting checklist General topic QuestionsTroubleshooting flowchart Troubleshooting flowchart Power-on troubleshooting overview Power subsystemPower-on checks Power-on timing approximate Boot sequenceTools for troubleshooting Component diagnosticsLED diagnostics Understand lights on the formatterEngine diagnostics Heartbeat LEDDefeating interlocks Defeat the right-door opening/closing sensor PS15Disable cartridge check Administration Troubleshooting Diagnostic TestsPaper-path test Engine test buttonManual sensor test 20Manual sensor diagnostic testsSensor or switch name Sensor or switch number Developer alienation sensor PS11 ITB alienation sensor Front-door opening/closing switch PS14 5Test the right-door opening/closing switch 1 Solve problems Right-door opening/closing sensor PS15Enww TOP top-of-page sensor PS5 Fuser loop sensors 1 and 2 PS7 and PS8 Fuser pressure-release sensor PS9 Fuser output sensor PS6 Developer alienation sensor PS11 ITB alienation switch SW5 Tray/Bin manual sensor test 21Tray/Bin manual sensor testEnww Tray 1 paper sensor PS2 Tray 2 paper present sensor PS1 Tray 2 paper surface sensor PS4 Tray 2 paper size switches SW7 and SW8 Tray 3 paper sensor SR3 Tray 3 paper surface sensor SR2 Tray 3 paper size sensors SW2 and SW3 Tray 3 feed sensor SR1 Tray 3 door opening/closing sensor SW1 Tray 4 paper sensor SR3 Tray 4 paper surface sensor SR2Tray 4 paper size sensors SW2 and SW3 Tray 4 feed sensor SR1Tray 5 paper sensor SR83 Tray 5 paper surface sensor SR82Tray 5 paper size sensors SW82 and SW83 Tray 5 feed sensor SR81Paper-path sensors test Output-bin-full sensor PS1022Paper-path sensors diagnostic tests Print/stop testComponent tests Component test special-mode test23Component tests 1 Switchback Motor Fuser Contact/Alienation DriveTrayX Pickup Motor DuplexerPickup Motor24Component tests 2 Additional component testsFull/half speed intake fan Full speed intake fan Speed controlled intake fanComponent test Component tested Comments Fuser Fan Formatter FanDiagrams Block diagrams26Optional paper feeder Tray 3 cross section Plug/jack locations DC controller connections Location of connectorsDC controller connections 25DC controller connections Product connections 28Product connections 129Product connections 2 30Product connections 3 31Product connections 4 32Product connections 5 33Product connections 6 34Paper feeder connections Locations of major components 35External component locations36Major component locations 1 Main drive unit Lifter drive unit 37Major component locations 2 38Major component locations 3 39Motors, fans, and rollers component locations 40PCA component locations General timing charts Timing chart 142General timing chart 2 General circuit diagram Fuser44 General circuit diagram 2 Paper feeder general circuit diagram 1 X 46Paper deck general circuit diagram 3 X Internal print-quality test pages Print-quality-troubleshooting pagesAdministration Troubleshooting Print Quality Pages Yellow Green 50Black print-quality troubleshooting Diagnostics Enww Clean the paper path Process a cleaningDevice Maintenance Calibration/Cleaning Set up an auto cleaningConfiguration Configuration51Configuration Security Settings information HP embedded JetdirectFinding important information on the configuration pages 26Important information on the configuration pagesAccessories and internal storage Diagnostics menuColor-band test Print quality troubleshooting tools Repetitive image-defect rulerCalibrate the product Sign In menu 27Sign In menuPersonal identification number PIN Might not be availableRetrieve Job From USB menu Retrieve Job From Device Memory menu 29Retrieve Job From Device Memory menuSupplies menu Settings Cartridge Prompt toSupplies menu 30Supplies menu Mix Mostly Color Transfer Kit Very Low StopColor/Black Auto Trays menu Use another tray Enabled Disabled Alternative Letterhead Disabled Mode EnabledSize/Type Prompt Display Do not display Blank Pages AutoAdministration menu Reports menu31Trays menu 32Reports menuMap Other Pages PrintGeneral Settings menu 33General Settings menuMidtones Cyan Density Enww Sets the sensing option for Tray 1 for paper types using When Expanded Adjust PaperSense Mode SensingHumidity Mode Normal High Light Media Normal Paper Curl Mode NormalOptimize Normal Paper Standard Cleaning Control Normal Envelope Control NormalEnvironment Normal Line Voltage Normal Low VoltageWhen a background When thin verticalWhen the other Correct the problemAlternate Alternative 1 to Moisture Control Normal AlternateMaximum is Jam Recovery AutoNormal is Held Timeout Hour Week Default FolderQuick Copy Job Off Name for StoredSettings Calibration Restrict Color EnableRetrieve From USB Settings menu Retrieve From USB Settings menuPrint Settings menu Append CR to LF Yes 35Print Settings menuFont Pitch Range 0.44 Default = Default Custom Paper Inches Dimension Dimension Range 5.00 Default =Print Options menu 36Print Options menuDimension Range 127 Default = Enable Edge to Edge EnabledOverrides Disabled MillimetersDisplay Settings menu Supply Settings Black Cartridge Very Low Stop Manage Supplies menu38Manage Supplies menu Status menu toNotifies you when Color/Black Mix Auto Mostly Color Pages Mostly Black First level Values Manage Trays menu39Manage Trays menu Use another tray Enabled Alternative Letterhead Mode DisabledFirst level Values Description Manually Feed Prompt Always Size/Type Prompt DisplayFirst level Values Description Blank Pages Auto First level Values Description Timeout Network Settings menuNetwork Settings menu Default IP Auto IP MethodRelease and Dhcp Renew Release0.0 IPv6 Settings Enable Address Manual EnableSettings Off Xxx.xxx.xx SecondaryRouter Unavailable If a Router Router Specified PolicyRouter Idle Timeout The time Https Optional Access802.1x Reset 00080Http Test Yes Diagnostics Embedded LAN HW Test YesTest Data Path Yes Select All YesTests Execution127.0.0.1 Dest IPv6 Print Results YesPing Results Packets Sent 00000Ping Yes Progress Enww Troubleshooting menu 42Troubleshooting menuSensors Paper Path Test Print TestTest Duplex Path Off NumberRepeat option Sensor TestRetrieve Export to USB Diagnostic DataRepeat Off Cleanup Debug Off DebugInformation File Include Crash OffDevice Maintenance menu Backup/Restore menu43Backup/Restore menu BackupsCalibration/Cleaning menu Cleaning Interval settingUSB Firmware Upgrade menu 44Calibration/Cleaning menuRefurbish Cycle Service menuCycle Counts Mono Cycle Counts Cold Reset Paper Letter Glass CleaningNew Registration Yes Roller10.0X.Y0 Supply memory error Memory errorDescription Label missing10.22.50 10.22.5110.22.52 10.23.50Printing past very low 10.23.5110.23.52 10.XX.40 Genuine HP supplies installed 10.XX.34 Used supply in use10.XX.41 Unsupported supply in use 10.XX.70 Printing past very lowFuser kit 10.31.15 10.YY.15 Install supply10.YY.25 Wrong cartridge in color slot 10.YY.35 Incompatible supply YY Internal clock error 13.00.0013.A3.FF 13.D3.DZ13.WX.EE 13.WX.FF13.WX.YZ Fuser area jam 13.WX.YZ Fuser wrap jam 13.WX.YZ Jam below control panel 13.WX.YZ Jam in lower right door13.WX.YZ Jam in middle right door 13.WX.YZ Jam in right door13.WX.YZ Jam in Tray 32.1C.XX Insufficient memory To continue, press OKToo complex Enww Recommended action Enww Enww Unsupported USB accessory detected To continue, press OK 32.21.00USB I/O buffer overflow To continue, press OK Embedded I/O buffer overflow To continue, press OKYZ Unexpected size in tray ErrorEmbedded I/O bad transmission To continue, press OK YZ Unexpected type in tray LBP OHTLBP OHT YZ Error To continue, press OK Enww 42.XX.YY 47.00.XX47.01.XX 47.02.XX47.WX.YZ Printer calibration error To continue, press OK 47.03.XX47.04.XX 47.05.0047.FC.23 50.WX.YZ Fuser error To continue, turn off then on Recommended action = 1 or W =Enww = a = BYY Error 52.XX.00 Error To continue, turn off then on54.XX.YY Error Recommended action 54.00.0354.00.06 or 54.00.14 or 54.01.0554.11.05 or 54.0X.0754.0X.0B or 54.0X.0C 54.0X.0D or 54.0X.0EYY DC controller error To continue, turn off then on 55.0X.YY DC controller error To continue, turn off then on YY Error To continue, turn off then on57.00.0Y Error To continue, turn off then on Recommended action 57.00.0157.00.02 57.00.03Recommended action 59.00.30 or 59.00.90 or 59.00.A059.0X.50 Error To continue, turn off then on 59.00.F0Recommended action 59.05.50 59.06.50 or 59.07.50 or59.0X.80 Error To continue, turn off then on 59.0X.60 Error To continue, turn off then on59.0X.70 Error To continue, turn off then on 60.00.0Y Tray Y lifting error Recommended action 50.05.8050.06.80 or 50.07.80 or Recommended action 60.00.0261.00.01 60.00.05 orNo system To continue, turn off then on Error To continue, turn off then on80.0X.YY Embedded JetDirect error Enww Corrupt data in firmware volume Corrupt data in solutions volumeCorrupt data in configuration volume Corrupt data in job data volumeUpgrade not performed error writing to disk Upgrade not performed file is corruptUpgrade not performed timeout during receive Upgrade not performed error reading upgrade Upgrade canceled by user Upgrade not performed the file is invalid99.00.2X Unsupported disk Unknown diskDisk data error No disk data installedDisk is not bootable please download firmware Incorrect disk99.XX.YY Binname Full Remove all paper from binSupply almost full Supply low or Supplies lowSupplyvery low or Supplies very low Tray X lifting File System device failure To clear, press OK File System file operation failed To clear, press OKFile System file system is full To clear, press OK File System is not initializedCalibration reset pending CancelingCanceling... jobname Bad optional tray connectionCleaning do not grab paper CleaningChecking engine Checking paper pathClearing event log Clearing paper pathClose front door Close lower right doorClose middle right door Close right doorClose upper right door For help press ? Cooling deviceCreating cleaning Data received To print last page, press OKEIO X disk initializing EIO X disk not functionalHP Secure Hard Drive disabled EIO X disk spinning upEvent log is empty Expected drive missingInitializing Incompatible supplyIncompatible supplies Install Fuser Unit Install supplyInstall supply Close rear door Internal disk not functional Install suppliesInstall Transfer Unit Internal disk spinning up Load Tray X Type, SizeManually feed Type, Size Loading program XX Do not power offLoad Tray X Type, Size To use another tray, press OK No job to cancel Manually feed Type, Size To use another tray, press OKMoving solenoid Moving solenoid and motorPaused Performing Color Band TestPerforming Paper Path Test Please waitPrinting Configuration Printing DiagnosticsPrinting Color Usage Log Printing DemoPrinting File Directory Printing Font ListPrinting Fuser Test Printing HelpPrinting PQ Troubleshooting Printing RegistrationPrinting RGB Samples Printing stoppedProcessing... copy X of Y Processing duplex job Do not grab paper until job completesProcessing... filename Ready Ready IP AddressRemove all print cartridges Remove at least one print cartridgeReplace supply Restore Factory Settings Replace suppliesRestricted from printing in color Rotating color motorRotating motor Size mismatch in TrayTray X empty Type, Size Sleep mode onSupplies in wrong positions Tray X open Type mismatch Tray TroubleshootingTray X overfilled Unsupported drive installed To continue, press OK USB accessory not functional Unsupported tray configurationUnsupported USB accessory detected Remove USB accessory Wrong cartridge in color slot Event-log messages 53Sample event logPrint the event log from the Administration menu Print the event log from the Service menuView an event log from the Administration menu Print an event logViewing the event log from the Service menu Clear an event logCommon causes of jams Product is jammed Cause SolutionClear jams Jam locations 54Jam locations500-sheet feeder use a SR1 tray feed sensor 46Paper path jam sensors47Event codes for jams Jam event code Jammed paper locationFuser modes for jam event codes Z Enww Clear jams in the upper-right door Enww Clear jams in the lower-right door Clear jams in Tray Enww Clear jams from Tray 2, Tray 3, or an optional tray Clear jams in the output bin area Jams in the fuser and transfer area Jam causes and solutionsJams in the output bin 51Causes and solutions for fuser delivery stationary jams 52Causes and solutions for duplexing reverse jams53Causes and solutions for duplex repick jams Jams in the duplex area duplex models onlyJams in Tray 1, Tray 2 and internal paper path 54Causes and solutions for residual media jams55Causes and solutions for pickup delay jam 1 tray pickup 56Causes and solutions for pickup delay jams Tray Door assembly. See Right-door assembly on57Causes and solutions for pickup stationary jams Causes and solutions for residual media jams58Causes and solutions for residual media jams Jams in Tray 3, 4, 5,Replace any defective parts Administration General Settings Jam Recovery Change jam recoverySet the jam recovery feature Solve paper-handling problems Product feeds multiple sheets Cause SolutionProduct feeds incorrect page size Cause Solution Product feeds multiple sheetsProduct pulls from incorrect tray Cause Solution Paper does not feed automatically Cause SolutionProduct pulls from incorrect tray Paper does not feed automaticallyTransparencies or glossy paper will not feed Paper does not feed from Tray 2, 3, 4, 5, or Cause SolutionTransparencies or glossy paper will not feed Cause Solution Output is curled or wrinkled Output is curled or wrinkled Cause SolutionEnvelopes jam or will not feed in the product Product will not duplex or duplexes incorrectly 61MP modes under the Adjust Paper Types sub menu Set to Up to resolve print-quality issues caused by poorUse manual print modes Or rough surface mediaHumidity Mode 62MP modes under the Optimize submenuMedia Temp Solve image-quality problems Print quality examplesProblem Sample Cause Solution Maintenance menu Execute the Clean Laser GlassItem in the Calibration/Cleaning Defective Power-supply Enww Cleaning kit CC468-67919 is Set up an auto cleaning Clean the productClean the paper path Supplies very low message is Solve performance problemsProblem Cause Solution Solve connectivity problems Solve direct-connect problemsSolve network problems Problem SolutionService mode functions Service menuTest Support Continuous Print from Automatic CalibrationsRestore factory-set defaults values Product resetsRestore factory-set defaults Clean Disk and Partial Clean functions Partial CleanActive and repository firmware locations PrintClean Disk Characteristics of a Partial CleanReasons for performing Partial Clean Execute a Partial CleanReasons for performing Clean Disk Execute a Clean DiskPreboot menu options Access the Preboot menuCold reset using the Preboot menu 63Preboot menu options 1Clean Disk Partial CleanPassword Clear Password64Preboot menu options 2 External 65Preboot menu options 3Disk Device 66Preboot menu options 4 67Preboot menu options 5 68Preboot menu options 5 Product updates Determine the installed revision of firmwarePerform a firmware upgrade Embedded Web ServerUSB storage device Preboot menu USB storage device control-panel menu Enww Parts and diagrams 1Order parts, accessories, and supplies Order parts by authorized service providersOrder parts, accessories, and supplies Customer self repair parts Supplies part numbers3Supplies part numbers Description Part numberEnww Service replacement parts Part number CSR level Solid state drive kit CE707-67901Fuser drive unit CE707-67904 Accessories part numbers 4Accessories part numbersHow to use the parts lists and diagrams Assembly locations External covers, panels, and doors 1External covers, panels, and doorsExternal covers, panels, and doors Description Part number QtyRight door assembly Simplex ModelRight door assembly Internal components 1 3Internal components 17Internal components 1 Internal components 2 4Internal components 28Internal components 2 Internal components 3 Duplex Model9Internal components 3 Internal components 4 6Internal components 410Internal components 4 Internal components 5 7Internal components 511Internal components 5 Internal components 6 8Internal components 612Internal components 6 Internal components 7 9Internal components 713Internal components 7 Internal components 8 10Internal components 814Internal components 8 Internal components 9 11Internal components 915Internal components 9 121x250 cassette Parts and diagrams 1x250 cassette1x250 cassette Description Part number Qty Cassette CE710-67906Paper pick-up assembly 13Paper pick-up assemblyPaper pick-up assembly Paper delivery assembly 14Paper delivery assembly Parts and diagramsPaper delivery assembly Printed circuit assemblies 15 PCAsPCAs 1x500 paper feeder 1x500PF external components1x500PF external components 1x500PF internal components 171x500PF internal components1x500PF internal components 1x500PF PCA 18 1x500PF PCA22 1x500PF PCA 3x500 paper feeder 3x500PF external components3x500PF external components 3x500PF internal components 20 3x500PF internal components3x500PF internal components 213x500PF cassette Parts and diagrams 3x500PF cassette3x500PF cassette Description Part number Qty Cassette 3x500PF RM1-6942-000CN3x500PF PCAs 22 3x500PF PCAs263x500PF PCAs Alphabetical parts list 27Alphabetical parts listInternal components 3 Internal components 2 PCAs on 3x500PF PCAs on Gear, 25T, duplex model RU6-0772-000CN Guide, slide RC2-7203-000CN Imaging high-voltage PCA RM1-6800-000CN Lifter plate assembly, Tray RM1-6043-030CN Paper delivery assembly Rail, cassette, right 3x500PF RL1-1390-000CN Sensor, right door WG8-5696-000CN Spring, tension, front RU6-2727-000CN Part number Description Numerical parts list28Numerical parts list RC2-6547-000CN Guide, fuser, rear RC2-6650-000CN Cover, main cross-member cable RC2-6715-000CN Hinge, front cover, right RC2-6842-000CN Guide, cable, right RC2-7201-000CN Slider, push RC2-9331-000CN Cover, left 1x500PF RK2-2276-000CN Fan, power supply RM1-6012-000CN Waste toner cover assembly RM1-6742-000CN Driver PCA duplex model RM1-6944-000CN Paper pick-up assembly 1x500PF RM1-7914-060CN Gear assembly, fuser RU6-2744-000CN Spring, tension, rear Enww Service and support Hewlett-Packard limited warranty statement Enww Enww Data stored on the print cartridge End User License Agreement Transfer Customer self-repair warranty service Customer support Enww Product specifications Physical specifications Table B-1Product dimensionsProduct Height Depth Width Weight Environmental condition Recommended AllowedRegulatory information FCC regulations Environmental product stewardship program Non-U.S. returns Return and recycling instructionsUnited States and Puerto Rico HP Color LaserJet Enterprise CP5520 Printer Series PaperMaterial restrictions Enww Declaration of Conformity For regulatory topics only Boise, Idaho USAOctober Certificate of Volatility Types of memoryVolatile memory Non-volatile memorySafety statements Laser safetyVcci statement Japan Power cord instructions Power cord statement JapanLuokan 1 laserlaite VaroitusGS statement Germany VaroSymbols/Numerics AccessoriesLED Msds Quality RecyclingSensor SW1 483 Supplies menu, control panel 258 Support Online 639 Page CE707-90935* *CE707-90935