Paradyne 392xPLUS operation manual LeasedLine Rate 28800V34

COMSPHERE 392xPlus Modems

Table 4-11

(2 of 5)

Leased Line Configuration OptionsÐ Singleport Mode A

LeasedLine Rate: 28800(V34) (Cont.)

4800(V27bis), 2400(V27bis) ± This modulation scheme is available on 2-wire (half-duplex) and 4-wire leased lines.

NOTE: It is recommended that both modems use the same fixed data rate.

NOTE: The modem must be in Direct mode before the modulation scheme can be changed from V.32bis, V.34 family, or TMp to another leased-line modulation (V.33, V.29, or V.22bis). See Err Contrl Mode configuration option for more about Direct mode. On leased lines, V.42 error control and Buffer mode are only supported by V.32bis, V.34 family, or TMp. An error occurs if the modem is not in Direct mode when the modulation is changed from V.32bis, V.34 family, or TMp.

The AT command is S-Register S44=n, where n is:

1	= 14,400 (V.32bis)	14 = 7200 (V.29)			23	= 7200 (TMp)	32 = 19,200 (V.34)
2	= 12,000 (V.32bis)	15 = 4800 (V.29)			24 = 4800 (TMp)		33 = 16,800 (V.34)
3	= 9600 (V.32bis)	16	= 4800	(V.27bis)	25	= 2400 (TMp)	34 = 14,400 (V.34)
4	= 7200 (V.32bis)	17 = 2400		(V.27bis)	26 = 33,600		35 = 12,000 (V.34)
5	= 4800 (V.32bis)	18	= 19,200 (V.32 terbo)		27 = 31,200		36 = 9600 (V.34)
6	= 2400 (V.22bis)	19 = 16,800 (V.32 terbo)			28	= 28,800 (V.34)	37 = 7200 (V.34)
11	= 14,400 (V.33)	20	= 19,200 (TMp)		29 = 26,400 (V.34)		38 = 4800 (V.34)
12 = 12,000 (V.33)		21	= 14,400 (TMp)		30 = 24,000 (V.34)		39 = 2400 (V.34)
13 = 9600 (V.29)		22 = 9600 (TMp)			31 = 21,600 (V.34)

Leased Mode: 4WLL-Ans

Nxt 4WLL-Ans 4WLL-Orig 2WLL-Orig 2WLL-Ans

Leased Mode. Sets the modem for either 2-wire or 4-wire operation in Answer mode (receiving a call) or 2-wire or 4-wire operation in Originate (initiating a call) mode.

NOTE: For proper operation of V.32 modulations over leased lines, one modem must be set to Originate mode and the other set to Answer mode.

For Sync Leased Answer Mode, Async Leased Answer Mode and Trellis Multipoint Tributary Mode, 4-wire Answer is the factory default.

For Sync Leased Originate Mode, Async Leased Originate Mode and Trellis Multipoint Control Mode, 4-wire Originate is the factory default.

The AT command for Disable is &L0.

The AT command for 2-wire Originate is &L1.

The AT command for 4-wire Originate is &L2.

The AT command for 2-wire Answer is &L3.

The AT command for 4-wire Answer is &L4.

Autorate: Enable

Nxt Enable Disable

This configuration option only appears when Leased Line Rate is configured for V.34 and V.32 families data rate.

Autorate. Once connected, the modem automatically lowers the line rate if line conditions become impaired. When line conditions improve, the modem automatically shifts up to the highest data rate the line can support. This autorating only occurs between 19,200 bps and 4800 bps during V.32, V.32bis, and V.32 terbo connections and 33.6 and 2400 for V.34.

The AT command is S-Register S82=n, where n is 0 for Enable and 1 for Disable.

V32bis Override: Disable

Nxt Disable 2400

This configuration option is ignored unless Leased-Line Rate is 4800(V32b).

V.32bis 4800 Override. Activates the Paradyne Point-to-Point Diagnostic 2400 bps modulation. Allows the modem to use a non-standard, point-to-point modulation capable of secondary channel diagnostics while running at 2400 bps.

4-54 November 1996 3920-A2-GN31-30