Clone Remote in Multipoint Configurations | Paradyne 392xPLUS

DCP Operation

Clone Remote in Multipoint Configurations

A Trellis Multipoint (TMp) control modem can be used to download firmware to just one tributary modem (Single) or to all of its tributary modems (Multiple).

NOTE

A Trellis Multipoint (TMp) tributary modem cannot download firmware to its control modem. To download firmware to a TMp control modem use a point-to-point dial connection, an NMS, or a PC controller.

Before using Clone Remote in multipoint configurations (Single or Multiple), perform the following:

•Make sure the 392xPlus modems have an established leased-line connection using the Trellis Multipoint (TMp) modulation (refer to the Leased Line section in Chapter 4).

•Make sure the remote modem's Access From Remote configuration option is enabled (refer to the Misc section in Chapter 4).

•For Single download configurations, know the remote access password and the network management address of the remote tributary modem that will receive the download. Refer to the Misc section in Chapter 4 for a description of the remote access password (RemAccssPasswrd) configuration option and the network management address (NetMngmtAddress) configuration option.

•For Multiple download configurations, ensure that:

Ðthe tributaries are responding properly to polls (this may take several minutes after the control modem powers up). Refer to the Sub-Network Health and Status Branch section in this chapter for more information.

Ðthe control modem's active poll list contains all the network management addresses for the remote 392xPlus tributary modems that will receive the download (refer to the Poll List Branch section in this chapter).

Ðall 391x modems are removed from the active poll list.

3920-A2-GN31-30

November 1996

3-45

Image 82

Paradyne 392xPLUS operation manual Clone Remote in Multipoint Configurations

Contents

Comsphere Trademarks Warranty, Sales, and Service InformationCopyright E 1996 Paradyne Corporation. All rights reserved Important Safety Instructions HE E HEE E Deed DE EE Eeee HE HE EE EED E Table of Contents DCP Configuration Model 3920 Plus Multiport Back Panel and Power Supply List of Figures Miscellaneous Configuration Options Ð Singleport Mode List of Tables Table of Contents Preface How to Use This ManualObjectives and Reader Assumptions Related Documents Introduction Overview Model 3920Plus Standalone Singleport Modem Comsphere 392xPlus ModelsModel 3920Plus Standalone Multiport Modem Multiport Modem Model 3920Plus Standalone Singleport and Multiport Modems Model 3921Plus Carrier-Mounted Singleport Modem Model 3921Plus Carrier-Mounted Multiport Modem Model 3921Plus Singleport Modem Model 3921Plus Multiport Modem 392xPlus Features 392xPlus Operational Modes Applications 392xPlus Singleport Features392xPlus Multiport Features Multipoint Digital Bridge Dual-Leased BackupModulation Multiport Backup Symbol Rate Supported Data Rates Government Requirements and Equipment Return United States Canada Specifications Description Technical SpecificationsTechnical Specifications for 392xPlus Modems Model 3920Plus Power Supply Technical Specifications for 392xPlus Modems Description Power Consumption Modem Installation 392xPlus Modem Package Customer-Supplied Equipment For the carrier-mounted models Model 3920Plus Modem Installation Connecting Cables to the Model 3920Plus Modem Model 3920Plus Multiport Back Panel and Power Supply DTE Connection Dial Backup Connection Power Supply ConnectionLeased Backup Connection Leased-Line Connection Removing and Replacing the Model 3920Plus Modem Model 3921Plus Modem InstallationNetwork Management System Connection Modems Back Connector Plates Installing the Model 3921Plus Modem CarrSlot 101A ↑ ↓ 101A Circuit Pack Lock Power On Selftst Passed 392xPlus Modem Power-UpSelecting Factory Configuration Options for 392xPlus Removing and Replacing the Model 3921Plus Modem Using the Diagnostic Control Panel DCP Model 3921Plus Faceplate and Shared Diagnostic DCP Operation Diagnostic Control Panels Status Indicators Model 3920Plus Diagnostic Control Panel Optional Sdcp and Model 3921Plus Faceplates 392xPlus DCP LEDs Label Color Indicates 392xPlus DCP LEDs Label Color Indicates Sdcp LEDs Left/Right Scroll Indicator Diagnostic Control Panel OperationRight Scroll Indicator Left Scroll Indicator Out of Range Indicator Remote Mode IndicatorKeypad Menu Structure Key Model 3921Plus only Status ConfigureCall Setup PList Top-Level Menu Status Top-Level Menu Status and Operational MessagesStatus Message Indicates Top-Level Menu Status Message Indicates Call Failure Firmware AT Command ResetCall Disconnect Download Result Common Operational Messages Dial Access Security MessagesDial Access Indicates Security Message Common Indicates Operational Message Leased19.2 abbb cdd ee f f f f Quick Configuration DisplayLeased28.8 Status Configure Xxxx yyyyy zz abbb cdd ee f f f f V32t FfffV34 V32b Status Branch Status Device HS Major Minor Device Health and Status DeviceHSStatus DeviceHS VF Health and Status Messages Status Health and Status Messages Type IndicatesThresh Security Ports Sig/Noise SigQualRcvLevel NrEchLvl Impul Hts Phase HtsEchoFreqOff DropOuts Identity Select DTE Port Port1Port2 Status Identity DTELSD DTR DSR Tst RxRate SymbolRateTxRate TxLevel StatusBackup Line=Pri 4w APL BackupBackup StatusBackup Bkup2wAPL=Good Line=Pri 4w APL Backup Status ScreensLine=Pri 2w APL Options OptionsRecord OptionsStatus 29V.33 Service Log Nxt Mm/dd/yy zz Service LogStatus ServiceLog Record Status Display Clear Configure Branch Poll List Branch Leased28.8 PList Control DisplayPoll List Display Clear Clear Clear function does not appear in Remote modeChange function does not appear in Remote mode Change Poll Listyyyyyy Ent Poll ListAdd Command CompleteAdd Poll List Change Add Poll List Add Acquire Acquire function does not appear in Remote modeAcquire Poll ListAcquir Abort xxx yyy Poll ListAcquir Num Acquired yyy Control BranchLeased28.8 Control Test Speaker Control Speaker ResetSpeaker Control Off Low Med Control DataStream ResetData Stream Select DS Port Port1 Port2 Data Stream All Enable Disable Data Stream Port1 DisableData Stream Port1 Enable Select DS Port Port1 All Control EIALEDs EIA LEDsSelect DS Port All EIA LEDsxxxxx Port1Port2 Make Busy/Remove Make Busy Make Busy Command CompleteControl MakeBusy ServiceLine Command Complete Service Line/Disconnect Service LineControl ServiceLine Control RemoveMakeBusy Control DiscServiceLine Download Software DwnLoadSoftware CloneRemote Control DownloadCodeChoose DLL Type SCClone Choose DLL Type DCBroadcast Cloning DC Broadcast RemoteDC Clone Results Nxt xxx Pass Clone Remote in Multipoint Configurations Cloning a Single TMp Remote Choose DLL Type Single Multiple Choose Password Ent yyyyyyyyChoose Address Ent MPtCloneResults Nxt xxx Pass ReprogramRemote AbortDownloadRemClone Status Establish Remote Incompat Modulat Access DisabledPassword Invalid No Response Automatic Firmware Download DownldOnly Mode ConfigureDownload Status Bank1 xxxx/yyyy VF Thresholds Edit Save Reset VF Thresholds UpdateControl VFThreshUpdate RSL High dBm Nxt RSL High dBm Valid Ranges for VF Thresholds Default Values Save VF Thresh Thd Out of Range Test Branch Test Abort Self Command CompleteAbort TestAbort Self Test LocAnalogLoop Loc Analog LoopTestLocal Loop Started Rem Digital Loop Remote Digital Loopback Pick Test Port Port1 Port2 Test RemDigitalLoopTestP1Rem Loop Started TMp tributary cannot perform a local digital loopback test Loc Digital LoopTest LocDigitalLoop Pattern TestP1Dig Loop Started Pattern Test and Digital Loopback Test Test Pattern TestP1Pattern Started Test P1Pattern BlksErrd=xxxxxxx Sub-Network Health and Status Branch Leased28.8 TestSubHS Call Setup Branch Call Setup function is not available in TMp Control mode Dial Leased28.8 CallSetupCall Setup Dial Disconnect DialDirectory Nxt Disconnect Disconnect Command CompleteDialDirectory01 Off Hook Answer Call Setup AnswerAnswer Command Complete Dial Standby/Return to Dial Call Setup ReturntoDial Call Setup Dial StandbyDial Standby Command Complete Change Directory Call Setup ChangeDirectory01 551234 z Nxt 02z Nxt 019W5556789z Nxt Call Setup DirectoryStatus Valid Dial Command ModifiersDirectory Status may not appear for certain countries Talk/Data Branch Talk/Data function is not available in TMp Control modeNumber Status Nxt 01Allowed Online28.8 CallSetup Idle28.8 Tlk/Data Security Branch Remote Branch Leased28.8 Security Remote Select Channel Secondary Prim Data blckd Leased28.8 Control ExitRem Diagnostic Control Panel Access Frnt Panl Acces GrantDeny DCP Configuration DCP Configuration Process DCP Configuration LdEditAreafrm ActivOperating Editing and Saving a Configuration OptionLdEditAreafrm Factory Choose Function EditSave Ld Fact Preset SyncLeasedChoose Mode Answer Originate Edit StrapGroup DTEInterface StrapsWhenDisc Nxt NoChange RemAccssPasswrd Nxt Choose Function Edit Save SummarySav EditArea to ActiveSaved Configuration Tables Multiport Mode l Multiport Mode DTE Interface Configuration Options Ð Multiport Mode l DTE Interface Ð Multiport Mode lMUX Mode TDM/MSD Nxt TDM/MSD Disable DTE Bridge DTE Interface Configuration Options Ð Multiport Mode l Rate at 12.0 K Nxt Disable 12000 9600 7200 4800 2400 Rate at 14.4 K Nxt Disable 14400 12000 9600 7200 4800 2400Rate at Nxt Disable 9600 7200 4800 2400 Rate at End Disable 2400 Rate at Nxt Disable 7200 4800 2400Rate at Nxt Disable 4800 2400 Async/Sync Mode Sync Nxt Sync Async Port EIA Sub-Group One for Each Port DTR Action Ignore Nxt Ignore StndrdRS232 CntrlsOnHook RTS Action StndrdRS232 Nxt StndrdRS232 Ignore SimCntlCar RTS/CTS Delay 0msec Nxt 0msec 10msec 50msec 150msec 600msec DTE LL CT141 Disable Nxt Disable Enable Rcv Remote Loop Enable Nxt Enable DisableDTE RL CT140 Disable Nxt Disable Enable DTE Alarm Mask Disable Nxt Disable Enable DTE Interface Configuration Options Ð Multiport Mode l Line Dialer Ð Multiport Mode l Line Dialer Configuration Options Ð Multiport Mode l Pause Time 2sec Nxt 2sec 4sec 6sec 8sec 10sec 20sec Fast Disconnect Disable Nxt Disable EnableLong Space Disc Enable Nxt Enable Disable NoAnswer Timout 45sec Nxt 45sec 30sec 60sec No Carrier Disc 2sec Nxt 2sec Disable 5sec 10sec 20sec No Data Disc Disable Nxt Disable 10min 30min 60min Dial Line Configuration Options Ð Multiport Mode l Dial Line Ð Multiport Mode lDial Modulation Nxt V34 V32Family Asymmetric Rate Disabled Nxt Enable Disable Train Time Long End Long Short Autorate Enable Nxt Enable Disable Leased Line Ð Multiport Mode lLeased Line Configuration Options Ð Multiport Mode l LeaseModulation Nxt V34 V32Family TMp Auto Dial Back Disable Nxt Disable Enable FastBackup DialStandbyTime 10min Nxt 10min 5min 1min Lease Lookback Disable Nxt Disable EnableDualLeasedLn Disable End Disable Enable CarrierOn Level ± 43dbm Nxt ± 43dbm ±26dbm V54 Address Disable Nxt Disable Address Values Test Configuration Options Ð Multiport Mode lTest Timeout Disable End Disable 30sec 60sec 240sec Test Ð Multiport l Miscellaneous Configuration Options Ð Multiport Mode l Misc Ð Multiport l Dir#1Callback Disable Nxt Disable Enable NetworkPosition Tributary End Tributary Control Diag Connection ModemDC Nxt ModemDC Nmscc Disable Link Delaysec 0 Nxt 0 1 2 5 10 20 Singleport Mode a Singleport Mode MUX DTE Interface Ð Singleport Mode a DTE Interface Configuration Options Ð Singleport Mode a DTE Interface Configuration Options Ð Singleport Mode a DTE Interface Configuration Options Ð Singleport Mode a DSR Control StndrdRS232 RTS/CTS Delay 0msec Nxt 0msec 10msec 50msec 150msec 600msec DTE Interface Configuration Options Ð Singleport Mode a DTE Interface Configuration Options Ð Singleport Mode a DTE Interface Configuration Options Ð Singleport Mode a DTE Dialer Ð Singleport Mode a DTE Dialer Configuration Options Ð Singleport Mode a DTE Dialer Configuration Options Ð Singleport Mode a DTE Dialer Configuration Options Ð Singleport Mode a DTE Dialer Configuration Options Ð Singleport Mode a DTE Dialer Configuration Options Ð Singleport Mode a Line Dialer Ð Singleport Mode a Line Dialer Configuration Options Ð Singleport Mode a BusyTone Detect Enable Nxt Enable Disable Long Space Disc Enable Nxt Enable Disable MakeBusyVia DTR Disable End Disable Enable Dial Line Configuration Options Ð Singleport Mode a Dial Line Ð Singleport Mode aDial Modulation Nxt V34 V32Family V21/V22/Bell Dial Line Configuration Options Ð Singleport Mode a Asymmetric Rate Enable Nxt Enable Disable Leased Line Configuration OptionsÐ Singleport Mode a Leased Line Ð Singleport Mode aLeaseModulation Nxt V34 V32Family TMp V33 V29 V27b/V22b LeasedLine Rate 28800V34 Auto Dial Back Disable Nxt Disable Enable FastBackup DialStandbyTime 10min Nxt 10min 5min 1min Lease Lookback Disable Nxt Disable Enable 42/MNP/Buffer Ð Singleport Mode a 42/MNP/Buffer Configuration Options Ð Singleport Mode a Err Contrl Mode V.42/MNPorBfr 42/MNP/Buffer Configuration Options Ð Singleport Mode a 42/MNP/Buffer Configuration Options Ð Singleport Mode a 42/MNP/Buffer Configuration Options Ð Singleport Mode a 42/MNP/Buffer Configuration Options Ð Singleport Mode a DTE RLCT140 Disable Nxt Disable Enable Test Ð Singleport Mode aTest Configuration Options Ð Singleport Mode a DTE LLCT141 Disable Nxt Disable Enable V54 Address Disable Nxt Disable Address Values Misc Ð Singleport Mode a Miscellaneous Configuration Options Ð Singleport Mode a Access frm Remt Enable Nxt Enable Disable Security Ð Singleport Mode a Switching Between Data Mode and Online Command Mode AT Command Set and S-RegistersOperating Modes Command Guidelines Escape Sequence and Escape Guard Time Result Codes Result CodesNumbers Word Description Delayed ⊗ Result Codes Numbers Word Description AT Command List AT Command Format Sequence 392xPlus AT Commands DescriptionCommand ATD9W5551234 Sn=r Error Only displays OK, CONNECT, RING, no Carrier Default Configuration Options DCP LCD M0, &Q0 DCP LCD \D0 \A3\C0 \G0 \N5 \X0 Register List Register Format 392xPlus S-Registers Description Enter a value from 0±255. The factory setting is S41 S45 S46 S52 = Ascii = Ebcdic S66 S74 S85 S91 S96 Dial Access Security Menu Tree a Status ªStatusº Control SubHS CallSetup Tlk/Data Table B-1 Troubleshooting BSymptom Action Modem Health Leased-Line Operation Dial Backup OperationTable B-2 Table B-3 Table B-4 Modem Ð DTE Connection Modem Ð VF Connection Table B-5 Table B-6 Table B-5 Modem Ð VF Connection Symptom ActionTable B-7 Mux Operation Symptom Action Online Operation Pin Assignments C EIA-232-D Pin Assignments Signal Circuit Function SourceTable C-1 EIA-232-D Pin Assignments Name Leased Dial RJ11 VF Connector Pin AssignmentsTable C-2 VF Connector Pin Assignments Type of Telco Jack Pin Auxiliary Cables Not Supplied Position Plug PIN no Figure C-4. Wiring Diagram Ð 25-Pin Crossover Cable Ccitt V.25bis Dialing D Command and Responses Call Request with Number Provided CRN Call Request CommandsCall Response Call Request with Stored Memory Address Provided CRS Delayed Call Indicator Call Answer CommandsCall Connecting CNX Incoming Call INC Request List of Forbidden Numbers RLF Request List of Delayed Numbers RLDProgram Normal PRN Connect Incoming Call CIC List Forbidden Numbers Response LSF List Delayed Numbers Response LSDRequest List of Stored Numbers RLN List Stored Number Response LSN Valid VAL Command ResponseInvalid INV List Response Command ResponseList Request Call Response Ascii Value Character Ascii Character Table ETable E-1 Ascii Characters Hexadecimal Decimal Control Key Ascii Value ETB CTRL-W Ascii Character Table Delete Default Configuration Options F Table F-1 Factory Default Configuration Options DTE Interface Multiport mode Port Rate Sub-group Contd DTE Interface Singleport mode Port EIA Sub-group Contd DTE Interface Singleport mode Contd DTE Dialer l DTE Dialer lContd Line Dialer Dial Line Lease Line Lease Line Contd 42 / MNP / Buffer l ²² Misc Security l Sample Configurations G Point-to-Point Configuration OptionsRate Refer to Sample Port Rate Table in this section Cables Port Rate Figure G-2. Sample Configuration Ð Extended Point-to-Point Extended Point-to-Point TX Clock Source Autorate Leased Line Set to Disable3910 a LeasedLine Rate Figure G-3. Sample Configuration Ð Extended Multipoint Extended Multipoint Plus B 3910 C Point-to-Point with Automatic Dial Backup Configuration Options Point-to-Point with Network Management Rate Refer to the Sample Port Rate Table in this section Cables Carrier with Network Management Comsphere Configuration Options Extended Diagnostics NetworkPosition Diag Connection NetMngmtAddress Adapter 871A LSD Control MUX ModeDigital Bridging DTR Action Cables Figure G-9. Sample Configuration Ð Point-to-Point MSD Point-to-Point MSD Sample Port Rate Table Point-to-Point MSD 3920Plus a Multipoint MSD MSD Control Cables Equipment Feature Part Number Equipment List H Glossary Backbone network Automatic dial standbyAutomatic rate control Backplane Configuration option Command modeConfiguration area Connector DBm Diagnostic Channel DCDial command modifiers Demodulation EIA RS-366-A Error controlEIA-232-D Escape sequence Keypad Multiport modeIdle Leased line Power-up self-test Originate modePhase jitter Quick Configuration Remote loopback Singleport modeRegister Result code Trellis-coded modulation Top-Level menuTraining Tributary modem Xoff Index DTE Index Index-4