Service error codes (9xx.xx) (continued)

Error

Sub

Display text

Description

Action

code

codes

 

 

 

 

 

 

 

 

 

 

920

.92

Hot roll fell too far below

Bad thermistor, circuit, or cabling.

Go to “920.xx—Cold fuser

 

 

desired temperature

Noisy thermistor signal.

service check” on page 2-87.

 

 

while printing. Fuser

 

 

 

Fuser not receiving AC power.

 

 

 

page count not

 

 

 

available.

• Poor supply line voltage.

 

 

 

 

 

 

 

 

Excessive load on the fuser.

 

 

 

 

Low voltage or incorrect lamp.

 

 

 

 

Incorrect hot roll.

 

 

 

 

 

 

 

920

.93

Hot roll too cool while

Bad thermistor, circuit, or cabling.

Go to “920.xx—Cold fuser

 

 

checking for slope

Noisy thermistor signal.

service check” on page 2-87.

 

 

change. Fuser page

 

 

 

Fuser not receiving AC power.

 

 

 

count not available.

 

 

 

 

• Poor supply line voltage.

 

 

 

 

Excessive load on the fuser.

 

 

 

 

Low voltage or incorrect lamp.

 

 

 

 

Incorrect hot roll.

 

 

 

 

 

 

 

920

.94

Hot roll too cool when

Bad thermistor, circuit, or cabling.

Go to “920.xx—Cold fuser

 

 

heating to desired

Noisy thermistor signal.

service check” on page 2-87.

 

 

temperature after slope

 

 

 

Fuser not receiving AC power.

 

 

 

change. Fuser page

 

 

 

count not available.

• Poor supply line voltage.

 

 

 

 

 

 

 

 

Excessive load on the fuser.

 

 

 

 

Low voltage or incorrect lamp.

 

 

 

 

Incorrect hot roll.

 

 

 

 

 

 

 

920

.96

Fuser is not increasing

Fuser is not receiving AC power.

Go to “920.xx—Cold fuser

 

 

in temperature even

• Poor supply line voltage.

service check” on page 2-87.

 

 

though the lamp has

 

 

 

 

 

 

 

 

been on for an extended

 

 

 

 

 

time. Fuser page count

 

 

 

 

 

not available.

 

 

 

 

 

 

 

 

 

920

.97

Fuser has been below

Bad thermistor, circuit, or cabling.

Go to “920.xx—Cold fuser

 

 

the desired temperature

Very noisy thermistor signal.

service check” on page 2-87.

 

 

for too long while media

 

 

 

Fuser not receiving AC power.

 

 

 

is in the nip. Fuser page

 

 

 

count not available.

• Poor supply line voltage.

 

 

 

 

 

 

 

 

Excessive load on the fuser.

 

 

 

 

Low voltage or incorrect lamp.

 

 

 

 

Abrupt change in temperatures that

 

 

 

 

 

has disrupted control.

 

 

 

 

 

 

 

922

.02

Hot roll took too long to

Low wattage or incorrect lamp.

Go to “922.xx—Cold fuser

 

 

reach the beginning

• Bad thermistor, circuit, or cabling.

check” on page 2-89.

 

 

lamp detection

 

 

 

Fuser not receiving sufficient AC

 

 

 

temperature. Fuser

 

 

 

page count between 0

 

power.

 

 

 

and 99,999.

• Poor supply line voltage.

 

 

 

 

 

 

 

 

 

 

 

Diagnostic information 2-15

Page 51
Image 51
Toshiba e-STUDIO500P manual Go to 922.xx-Cold fuser, Check on