Bose MR-J2S- B MR-J2S-10B1, MR-J2S-20B1, MR-J2S-40B1, MR-J2S-60B, 10.8, MR-J2S-70B, MR-J2S-100B

11. CHARACTERISTICS

11.2 Power supply equipment capacity and generated loss

(1)Amount of heat generated by the servo amplifier

Table 11.1 indicates servo amplifiers' power supply capacities and losses generated under rated load. For thermal design of an enclosure, use the values in Table 11.1 in consideration for the worst operating conditions. The actual amount of generated heat will be intermediate between values at rated torque and zero torque according to the duty used during operation. When the servo motor is run at less than the maximum speed, the power supply capacity will be smaller than the value in the table, but the servo amplifier's generated heat will not change.

Table 11.1 Power supply capacity and generated heat per servo amplifier at rated output

			(Note 1)	(Note 2)		Area required for heat dissipation
Servo amplifier	Servo motor		Power supply	Servo amplifier-generated heat[W]
			capacity[kVA]	At rated torque	With servo off	[m2]	[ft2]
	HC-KFS053	13	0.3	25	15	0.5	5.4
MR-J2S-10B(1)	HC-MFS053	13	0.3	25	15	0.5	5.4
	HC-UFS13		0.3	25	15	0.5	5.4
	HC-KFS23		0.5	25	15	0.5	5.4
MR-J2S-20B(1)	HC-MFS23		0.5	25	15	0.5	5.4
	HC-UFS23		0.5	25	15	0.5	5.4
	HC-KFS43		0.9	35	15	0.7	7.5
MR-J2S-40B(1)	HC-MFS43		0.9	35	15	0.7	7.5
	HC-UFS43		0.9	35	15	0.7	7.5
MR-J2S-60B	HC-SFS52		1.0	40	15	0.8	8.6
	HC-SFS53		1.0	40	15	0.8	8.6
	MR-KFS73		1.3	50	15	1.0	10.8
MR-J2S-70B	HC-MFS73		1.3	50	15	1.0	10.8
	HC-UFS72	73	1.3	50	15	1.0	10.8
MR-J2S-100B	HC-SFS81		1.5	50	15	1.0	10.8
	HC-SFS102	103	1.7	50	15	1.0	10.8
	HC-SFS121		2.1	90	20	1.8	19.4
	HC-SFS201		3.5	90	20	1.8	19.4
	HC-SFS152	153	2.5	90	20	1.8	19.4
MR-J2S-200B	HC-SFS202	203	3.5	90	20	1.8	19.4
	HC-RFS103		1.8	90	20	1.8	19.4
	HC-RFS153		2.5	90	20	1.8	19.4
	HC-UFS152		2.5	90	20	1.8	19.4
	HC-SFS301		4.8	120	20	2.7	29.1
MR-J2S-350B	HC-SFS352	353	5.5	130	20	2.7	29.1
	HC-RFS203		3.5	90	20	1.8	19.4
	HC-UFS202		3.5	90	20	1.8	19.4
	HC-SFS502		7.5	195	25	3.9	42.0
	HC-RFS353		5.5	135	25	2.7	29.1
MR-J2S-500B	HC-RFS503		7.5	195	25	3.9	42.0
	HC-UFS352		5.5	195	25	3.9	42.0
	HC-UFS502		7.5	195	25	3.9	42.0
MR-J2S-700B	HC-SFS702		10.0	300	25	6.0	64.6

Note:1. Note that the power supply capacity will vary according to the power supply impedance.

2.Heat generated during regeneration is not included in the servo amplifier-generated heat. To calculate heat generated by the regenerative brake option, use Equation 12.1 in Section 12.1.1.

11 - 3