12.OPTIONS AND AUXILIARY EQUIPMENT

(d)Line noise filter (FR-BLF, FR-BSF01)

This filter is effective in suppressing noises radiated from the power supply side and output side of the servo amplifier and also in suppressing high-frequency leakage current (zero-phase current) especially within 0.5MHz to 5MHz band.

Connection diagram

Wind the 3-phase wires by the equal number of times in the same direction, and connect the filter to the power supply side and output side of the servo amplifier.

The effect of the filter on the power supply side is higher as the number of winds is larger. The number of turns is generally four. If the wires are too thick to be wound, use two or more filters and make the total number of turns as mentioned above.

On the output side, the number of turns must be four or less.

Do not wind the grounding wire together with the 3-phase wires. The filter effect will decrease. Use a separate wire for grounding.

Example 1

 

NFB

 

 

 

 

 

Servo amplifier

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L1

supply

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line noise

 

 

 

 

 

L3

 

 

 

 

 

 

 

 

 

filter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Number of turns: 4)

Outline drawing [Unit: mm] ([Unit: in.])

FR-BLF(MR-J2S-350B or more)

 

7 (0.28)

(1.24)

(0.28)7

31.5

130 (5.12)

 

85 (3.35)

 

80(3.15)

35(1.38)

 

(0.09)

160 (6.30)

2.3

180 (7.09)

 

FR-BSF01(for MR-J2S-200B or less)

Example 2 NFB

 

 

 

 

 

 

 

 

 

 

 

 

Servo amplifier

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

supply

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line noise

 

 

 

 

 

 

 

 

L3

 

 

filter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Two filters are used

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Total number of turns: 4)

22 (0.87)

110(4.33)

95 (3.74)

65(2.56) 33 (1.3)

2-5 (0.20)

(0.12)

65(2.56)

3

 

 

 

 

 

 

 

(e)Radio noise filter (FR-BIF)...for the input side only

This filter is effective in suppressing noises radiated from the power supply side of the servo amplifier especially in 10MHz and lower radio frequency bands. The FR-BIF is designed for the input only.

Connection diagram

Outline drawing (Unit: mm) ([Unit: in.])

Make the connection cables as short as possible. Grounding is always required.

Servo amplifier

 

 

NFB

L1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power

 

 

 

 

 

L2

 

 

 

 

 

 

supply

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Radio noise filter FR-BIF

About 300(11.81)

Red White Blue

Green

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

29 (1.14)

42 (1.65)

58 (2.28)

Leakage current: 4mA

 

5 (0.20)

 

(0.16)4

 

hole

29 (1.14)

7 (0.28)

 

44 (1.73)

12 - 32

Page 163
Image 163
Bose MR-J2S- B instruction manual On the output side, the number of turns must be four or less