14.4 E2PROM write selection, 132 | Mitsubishi FR - S500 instruction

<Setting>

	n10		Operation Mode	Mode at Power-On or at Power Restoration
	Setting	Pr. 79	Operation Mode	after Instantaneous Power Failure
	Setting	Pr. 79		after Instantaneous Power Failure
		0	PU or external operation	Placed in the external operation mode.
		1	PU operation	Placed in the PU operation mode.
		2	External operation	Placed in the external operation mode.
			External/PU combined	The running frequency is given in the PU
		3	External/PU combined	operation mode and the start signal in the
		3	operation mode	operation mode and the start signal in the
			operation mode	external operation mode.
				external operation mode.
			External/PU combined	The running frequency is given in the external
		4	External/PU combined	operation mode and the start signal in the PU
		4	operation mode	operation mode and the start signal in the PU
	0		operation mode	operation mode.
	0			operation mode.
	(Factory			MRS signal ON .....Can be switched to PU
	setting)			operation mode.
		7	External operation mode	(Output stop during
		7	External operation mode	external operation)
				external operation)
				MRS signal OFF ...Switching to PU operation
				mode inhibited.
				X16 signal ON .......Switched to external
		8	External/PU combined	operation mode.
		8	operation mode	X16 signal OFF .....Switched to PU operation
			operation mode	X16 signal OFF .....Switched to PU operation
				mode.
		0	Computer link operation	Disabled when PU is selected. Enabled when
		0	Computer link operation	external is selected.
				external is selected.
		1	PU operation only	Disabled
		2	Computer link operation	Enabled
		3	External/PU combined	Disabled
		3	operation	Disabled
	1		operation
	1	4	External/PU combined	Disabled
			External/PU combined
			operation
			operation
		7	External operation (PU	Enabled only for external operation when the
		7	operation interlock)	PU interlock signal (MRS) is ON.
			operation interlock)	PU interlock signal (MRS) is ON.
		8	PU or external (signal	Enabled only for external operation (X16: ON).
		8	switching)	Enabled only for external operation (X16: ON).
			switching)

n10 can be changed independently of the operation mode of the operation panel.

Setting of n10 = "1" is made valid when "0" or "2" is set in Pr. 79 "operation mode selection".

Refer to to (page 118)

2.14.4 E2PROM write selection

You can choose whether the parameters are stored into E2PROM or not at the parameter setting for computer communication.

	Parameter	Name	Factory	Setting	Remarks
	Parameter	Name	Setting	Range	Remarks
			Setting	Range
		E2PROM write			0: Written to RAM and E2PROM
	n12 (342)	E2PROM write	0	0, 1	1: Written to RAM only
	n12 (342)	selection	0	0, 1	Not written to E2PROM*
					Setting is enabled when Pr. 30 = "1"

The parameter number in parentheses is the one for use of the parameter unit (FR-PU04). * When reset is performed, the parameter value will be the value of E2PROM.

132

Image 141

Mitsubishi FR - S500 instruction manual 14.4 E2PROM write selection, 132

Contents

SR5 0 This section is specifically about safety matters Conditions, resulting in death or severe injuryCause physical damage only Page Page Page Multi-speed setting RL, RM, RH, REX signals Setting 0, 1, 2 How to Use the Input Signals Biases and gains of the frequency setting voltage current Handling of the RS-485 ConnectorStall prevention Frequency jump Operation mode selection PID control 101 Restart settingMonitoring reference Retry function PWM carrier frequency Applied motor 137 To know the operating status at the occurrence of alarm145 Correspondence between digital and actual characters 145 Abbreviations Wiring Terminal connection diagram Japanese VersionFR-S520-0.1K to 3.7K -R -C FR-S540-0.4K to 3.7K -R Layout and wiring of main circuit terminals FR-S520S-0.1K to 1.5K -R -C FR-S510W-0.1K to 0.75K -RNFB MC North America Version InverterFR-S520-0.1K to 3.7K-NA FR-S540-0.4K to 3.7K-NA R FR-S510W-0.1K, 0.2K, 0.4K-NA FR-S510W-0.75K-NA Reduce the output current FR-S540-0.4K to 3.7K-ECR European Version FR-S520S-0.2K to 1.5K-EC R FR-S540-0.4K, 0.75K, 1.5K, 2.2K, 3.7K-EC RFR-S520S-0.2K, 0.4K, 0.75K-EC R FR-S520S-1.5K-EC R Main circuit Description of I/O Terminal SpecificationsControl circuit Terminal names in parentheses are those of the EC version RUN Cables, wiring lengths, crimping terminals, etc How to Use the Main Circuit TerminalsFR-S520S-0.1K to 1.5K -R FR-S520S-0.2K to 1.5K-EC R FR-S510W-0.1K to 0.75K -R FR-S510W-0.1K to 0.75K-NA Wiring instructions Selection of peripheral devices Peripheral devices AC Reactor DC Reactor Model L1, NCables mm2 Line-to-line leakage currents To-ground leakage currents Type SP, CF, SF, CP During commercial powerRated sensitivity current ∆ n ≥ 10 ⋅ lg1+Ign+lg2+lgm Inverters primary side magnetic contactor MC Power-off and magnetic contactor MCOFF STF STR NFB FR-BAL Regarding noise and the installation of a noise filter Noise reduction examples Grounding precautionsBLF BIF Japanese power harmonic suppression guideline Regarding power harmonics Received Power Voltage 5th 7th 11th 13th 17th 19th 23rd Over Conversion Factors for FR-S500 Series Harmonic suppression techniques Harmonic suppression technique requirementRated 6kV No reactor, 100% operation ratio How to Use the Control Circuit Terminals Terminal block layoutM3 A, B, C terminals Al 0.5-6WH Input signals are set to sink Using tweezers, a pair of longChanging the control logic RUN 24VDC STR STR R Right The forward/reverse rotation signal is Input TerminalsRun start and stop STF, STR, Stop Three-wire type connection STF, STR, Stop STR-SD STF-SD Basic Voltage input 10, 2 External frequency selection REX, RH, RM, RL Manual-Automatic SwitchingCurrent input 4, 5, AU AU-SD on OFF REX External command Japanese version FM Indicator connection and adjustment Output waveform of terminal FM CPU NA and EC version AM Control circuit common terminals SD, 5, SE Signal inputs by contactless switches Second function selection RT signal Setting Current input selection AU signal SettingStart self-holding selection Stop signal Setting External thermal relay input Setting Output shut-off MRS signal Setting Jog operation JOG signal Setting Reset signal SettingJog operation using external signals PU operation/external operation switching Setting PID control valid terminal SettingWhen connecting the parameter unit Use the optional FR-CB2 System configuration examples RS-485 communication4P Twisted pair cable, 4 pairs Wiring of one RS-485 computer and one inverter Wiring methods MC1 Design Information Communication Parameters Only for the Type Functions Function Parameter List Func- Pa- Indica- tion rame- tion ter Minimum Factory Cus Name Setting Range Minimum Factory Refer Cus Name Setting Range FM AM THM, THT, GF OHT, OLT, PE, OPTPWM Selection functions PID ECL Alarm history 115 Clear Func Tion CationNA, EC Com Minimum For details of the program, refer to page 118 onwards List of Parameters Classified by Purpose of Use Related to monitoring Name Factory Setting Remarks SettingExplanation of Functions Parameters Torque boost Parameter Name Factory Setting Setting Range EC version Maximum and minimum frequencyBase frequency, Base frequency voltage EC version Remarks Range Multi-speed operation to to Acceleration/deceleration time Frequency setting Hz 120 Acceleration Deceleration time s Electronic overcurrent protection DC injection brakeOperation, etc. or the timing of operating Name Factory Starting frequency Load pattern selection Jog frequency Name Factory Setting Setting Range RemarksRUN key rotation direction selection Refer to Refer to , Stall prevention function and current limit function Stall Prevention OL Signal Operation Fast OutputCelerationDe Operation Activated Deceleration Operation Not Activated Regenerative Driving Stall prevention Where, a = 100 Acceleration/deceleration pattern Set the acceleration/deceleration patternFunction Description Frequency jump Extended function display selection Speed display Setting Biases and gains of the frequency setting voltage currentName Factory Setting Use Pr , calibration parameter C4 for Flicker ... Parameter setting complete How to change the highest frequencyOperationDisplay Set value Hz Press the SET key to set the value Voltage gain appears Press the SET key to show the analog Turn the setting dial to read another parameter Key to return toKey twice to show the next parameter Start-time ground fault detection selection Output Terminal Function ParametersUp-to-frequency sensitivity Output frequency detection Current Detection Function Parameters Parameter Name Factory Setting Remarks RangeOutput current detection functions On OFF Zero current detection Display Function Parameters Monitor displayLED Setting dial function selection Press the RUN key to start the inverterRefer to Restart Operation Parameters Restart settingMonitoring reference Maximum output voltage of terminal AM is 5VDC Refer to the following table and set the parameters Setting DescriptionAutomatic restart operation after Stfstr Or PU digital preset frequency Remote setting function selectionOperation panel operation procedure Additional Function Parameters Frequency setting storage conditions Pr SettingFunction E 2PROM Input terminal function selection Terminal Function Selection Parameters MRS Setting Signal Functions Related Parameters NameREX JOG Output terminal function selection Setting Signal Function Operation ParametersSame function may be set to more than one terminal Referred to Operation Selection Function Parameters Pr Setting Number of Retries Alarm Signal OutputRetry function Protective Functions Major Failures for Retries Parameter Number Setting Description PWM carrier frequencyYou can change the motor sound Voltage input selection Applied motorSet the motor used Acceleration/deceleration time, which is a slope up/down to Parameter Name Factory Setting Setting Range Remarks Reset selection/PU stop selectionSetting Remarks Reset Selection PU Stop Selection Setting Operation panel Restarting method with Shown Key input from Cooling fan operation selection Parameter write inhibit selection Pr Setting Function Reverse rotation prevention selection Operation mode selection Function LED Indication * PU Mode SignalEXT RUN EXT MRS PU operation interlock Operation mode switching by external signal X16 Signal Operation ModePID control to Setting Basic PID control configuration PID action overview102 Reverse action PID actionIncreases the manipulated Variable output frequency if Deviation X = set point Deviation Wiring exampleNegative RUNFUP,FDN Parameter setting O signalsName Setting Description 105 106 Adjustment procedure 107 Calibration exampleStart END Set point input calibration Detector output calibration108 Slip compensation Auxiliary Function Parameters11.2 Automatic torque boost selection Operating conditions 110Ordinary V/F control and torque boost Pr , Pr are valid Calibration Parameters Parameter Name Factory Setting RemarksMotor primary resistance Meter frequency meter calibration Japanese version 112 Flicker ... Parameter setting complete Meter frequency meter calibration NA and EC version When the FR-PU04 is used, make calibration with Pr 114 OperationDisplay Erases the alarm history Alarm history clearClear Parameters Parameter clear Operational functions Symbol Switching Type Operation mode-based functions 14.1 Communication settingsCommunication-related parameters 118 Description Setting 119CR LF Computer programming Communication protocol Operation Run RunningInverter Monitor Parame Reply data from inverter to computer during data write Data formatReply data from inverter to computer during data read 121 Data definitions Signal Ascii Code DescriptionSend data from computer to inverter during data read Control codes STX ACK ENQ 123 Instruction Data 124H7F HFFPage Setting items and set data 126FF = Calibra 127HEC Nication Tion Error Definition Error Code List128 Description Data Communication error Operation at alarm occurrenceGeneral flowchart Program example Operation and speed command write Location Selection N8 Pr Operation Command writeN9 Pr Speed Command write N8 Pr operation Command write Link start mode selectionN10 Link start mode Setting is enabled when Pr = Selection Explanation of table External 14.4 E2PROM write selection Parameter unit display language switching Parameter Unit FR-PU04 SettingN13 Setting Display Language 15.2 N15 PU contrast adjustment Setting is enabled when Pr = PU contrast adjustmentPU main display screen data selection N16 100 PU disconnection detection/PU setting lock Monitor display and Resetstop key are validN17 Setting PU Disconnection Detection PU Setting Lock 136 Functions Error alarm definitions Errors AlarmsMajor failures OC1 FR-PU04 OC2 FR-PU04 138OC3 FR-PU04 OV1 FR-PU04 OV3 139THM THT OHT FR-PU04 140OLT FR-PU04 OPT FR-PU04 For only the type having the RS-485 communication function Minor failures141 PUE 142 Write errors Er1 FR-PU04 Control Mode143 144 Er2 FR-PU04 PU/EXT ModeOperator ERR Er3 FR-PU04 Incr I/P Resetting the inverter Correspondence between digital and actual charactersActual Display Motor remains stopped Troubleshooting Motor rotates in opposite direction Speed greatly differs from the settingAcceleration/deceleration is not smooth Motor current is large Operation panel display is not operating Operation mode is not changed properlyParameter write cannot be performed Motor produces annoying sound Precautions for maintenance and inspection Precautions for Maintenance and InspectionCheck items Periodic inspection Pressure test Insulation resistance test using meggerDaily and periodic inspection Interval Daily Inspection Description 151Interval Daily 1 year Inspection Interval Checking the inverter and converter modules Preparation Checking methodModule device numbers and terminals to be checked Part Name Standard Replacement Interval Description Replacement of partsCooling fan Inverter Model No Fan Type AIR Flow Relays Smoothing capacitors Typical Measuring Points and Instruments Measurement of main circuit voltages, currents and powers Pf2= Pf1=158 Measuring Point Remarks Instrument Reference Measured Value RH, RM, RL, MRS Measuring PointRES-SD Measuring Remarks Instrument 160 Cations Specification List Phase 200V power supplyRatings Phase 400V power supply Single-phase 200V power supply Single-phase 100V power supply Common specifications NA, EC Outline Drawings 168 Parameter unit FR-PU04 Outline drawing Panel cut dimension drawing 170 Instructions Peripheral Selecting Instructions Selecting Instructions Disuse of power factor improving capacitor power capacitor Installation of thermal relayHandling of primary side magnetic contactor Handling of secondary side magnetic contactor Wiring Cable thickness and wiring distanceOperating Instructions Operation Power supply Installation Inverter-driven 400V class motor Rectifying the motor insulationSuppressing the surge voltage on the inverter side 176 Appendix Data Code Computer Func- Parameter tion NumberExtension Link Data 178 Data Code Computer Link Parameter ExtensionRead 179 180 181 Link Parameter Extension Setting Data Code 7F/FFData Code Computer Func Name Link Data Tion Print Date Manual Number Revision Manual number is given on the bottom left of the back cover