Replacing the Fuses, Back of Printer Fuse Under Cover | SATO CL412E

Section 6. Replacement Procedures

6.3 Replacing the Fuses

Fuse replacement is described in the following section.

·6.3.1 Removing and Replacing the Main Power Fuse

·6.3.2 Removing and Replacing the Internal Fuse

NOTE: Before replacing a fuse, determine the cause of the overload condition.

6.3.1Removing and Replacing the Main Power Fuse

Required: F15A, 250V Fuse Fuse

STEP

PROCEDURE

1.Switch the printer OFF and disconnect the power cable.

2.Locate the fuse cap on the back of the printer. Unscrew the cap and remove the defective fuse. Fig. 6-7

3.Replace the fuse with one of equal rating (15A, 250V). Do not use a fuse with a higher rating.

4.

Screw the fuse cap back and connect the power cable.

BACK OF PRINTER

FUSE (UNDER COVER)

Fig. 6-7

PN 9001078	SATO CL408e/CL412e Service Manual	Page 6-7
Rev. B

Image 107

SATO CL412E service manual Replacing the Fuses, Back of Printer Fuse Under Cover

Contents

CL408e/CL412e Printers Sato America, Inc Table of Contents Mechanical Adjustments Optional Accessories PN 9001078 Rev. B Overview Section TOP Access Physical CharacteristicsFront Access Door Label OUT Slot Memory Card Slot Printer FeaturesRear Panel Ribbon Supply Spindle Front Access Door Interlock Dispenser Label GuideFor Optional Label Label Sensor SensorsRibbon Motion Sensor Line KEY PRINT/OFFSET/PITCH Potentiometers Operation Panel Potentiometers Print ConnectorLCD Display Panel Line KEY Accessory Installation ConsiderationsOptional Accessories Environment & Approvals General Printer Specifications General Printer Specifications CPU Character Fonts Bar Codes Specification CL408e CL412e DSW1 Dip Switch Settings Setting RS232 Transmit/Receive Setting located on RS232 I/F Module DSW2 Printer Set up DSW3 External Signal Interface Setting DSW3 Dip Switch Selections Default Settings Mode KEY Sequence Initial Display LCD Panel Configuration 000000 LCD Panel Normal ModeInitializing Rom QTY Print speed 4 5 Print Speed AdjustmentPitch Offset Adjustment Step Procedure C D E F G Cancel Print Job Cancel print job Yes noCancel print job LCD Panel- Normal Mode Zero Slash Initializing Advanced mode RomLCD Panel- Advanced Mode Auto online Set calendar LCD Panel Advanced ModePrint offset +0000 Calendar 00/00/00 Character Pitch Ignore cr/lfCover open sensor Yes No Ignore CR/LF Mem Select CC1 Advanced Mode Card ModeLCD Printer Card Mode Copy start Yes no LCD Panel Card Mode Mode Card -MemoryCopy SATOFont y/nLCD Panel Card Card memory Copying Card -MemoryCopy All y/n Memory- card copy copying Memory -cardCopy All Card-Memory Copy Program Y/N Card -memoryCopy Program y/nCard- memory copy copying Memory-Card Copy Program Y/N Memory-cardCopy Program y/n Card Format Yes No Card format Yes noMemory format Yes no Gap X.XV Input Service modeLCD Panel Service Mode Gap x.xv input Gap x.xv input Eye Input Eye x.xv input Auto Online Feed Yes No Feed on error yes noAuto online feed yes no Reprint w/feed yes no EXt pin9 Select Mode Mode2 Forward/backfeed distance default Select language english Ignore can/dle Yes no Ribbon near end Enable disableService Mode Head Count clear Yes no Counters modeLCD Panel Counters Mode Counters Hd dsp cut life Test Print Mode Test print mode configuration Test print Size Default setting Yes noLCD Panel Test Print Mode Default Setting Mode Counter clear all Factory modeInitializing DiPSw2-4 on-off All clear Counter eeprom All clear modeCounter all clear All clear mode Completed LCD Panel Maintenance Mode All Clear Mode Download User Defined Protocol Codes LCD Panel Clear Non-Standard Protocol User Download Press the Line Key Countinued Hex Dump ModeInitializing Rom Online Qty000000 LCD Panel Download User Defined Protocol Codes Initializing Flash download LCD Panel -Firmware Download Mode Memory Head Check Factory ConfigurationSample Test Labels Interface Types InterfaceSpecifications Centronics RS232C Serial USB Interface Ethernet Multi Job Buffer Receive Buffer Data Streams Ieee 1284 Parallel Interface PIN Assignments Ieee 1284 Cable END PIN SignalPIN Direction RS232C Serial Interface General SpecificationsElectrical Specifications Printer Cable RequirementsDB9 Host Interconnection Ready/Busy Flow Control Signal Description On/X-Off Flow Control Universal Serial Bus USB Interface Bi-Directional Communications Ethernet Interface Pin Assignments Accessory EXT Connector Standard Operation Repeat Print Error Signals Interface Specifications Electrical Checks and Adjustments Remove 2 Screws Holding the Side Cover To the Outside Frame Steps Prior to Some Procedures Main PCB VR4 GAP VR1 OFS Test Point VR2 DEM VR3 CE DC Power Voltage ChecksPower Supply VR5 IM Receptacle on Connector Nibs onConnect TP Test Module to PCB Test Point @ Main PCB TP Test Module To PCB Test Point @ CN13 Test Point Chart Potentiometer Assignments & Adjustments VR5 IM PITCH-VR Step Procedure 5a Print Position Adjustment Test print Press the feed key 5b Print Position AdjustmentRefer to .2 for access to main PCB Refer to .2 for access to main PCB Label Gap Adjustment Eye-Mark Adjustment OFFSET-VR Offset Label Stop Position Adjustment 9a Ribbon Sensor Operation Verification Initializing OnlineRibbon end 9b Ribbon Sensor Voltage Checking High Value ~ Ribbon Sensor Voltage Checking Adjust Pitch Potentiometer For Optimum Print Step Procedure Print Darkness Adjustment MechanicalAdjustments# Raise the TOP Access Door Open the Front Ribbon Clutch Adjustments Unwind Ribbon Spindle Tension Gauge Core Locking Screw is Inside Adjust NUTTension Gauge Rewind String Empty Ribbon Ribbon Unwind Clutch Adjustment Guide Plate Ribbon Guide Plate Adjustment LIP Mounting Screws Tear Plate AdjustmentFigs Print Head Position Alignment Adjustment Marks Ribbon Adjust Platescrews Loosen Screw Print Head Balance Adjustment Indexing Pointer Shifts Head BACKWARD/FORWARD Print Head Alignment Adjustment Timing Belts Motor Mounting Screws Timing Belt Tension Adjustment ReplacementProcedures$ Replacing the Main Circuit Board Replacing the Main Circuit Board Disconnect Cable Disconnect Cables Memory Module PCB Replacing the Main Circuit Board Back of Printer Fuse Under Cover Replacing the Fuses Fuses Main PC Board Removing and Replacing the Internal Fuses Replacing the Power Supply Remove Screws Power Supply Detach Connectors Stepper Detach Connector Remove ScrewsReplacing the Stepper Motor Replacing the Timing Belts Detach Connector Loosen 4 Stepper Motor Mounting Screws Rewind Spindle Center Screw Replacing the Print Head Replacing the Print Head PN 9001078 Rev. a Replacing the Platen Belts Motor Platen Remove Timing List 6A Open the Front Access DoorReplacing the Ribbon Drive Clutch Washers Rewind Spindle Unwind Spindle Remove & InstallParts in this Order See Item List 6A Assemble Holes Disk Plate Item 11 Teeth Facing Outward to Engage Item 10 Felt WasherWith 2 Screws Item 9A/9B Display Panel PCB Replacing the Ribbon Motion SensorRemove Screw Sensor Left Side of Printer Remove Screws Replacing the Label Sensor Slide Cable Through Hole in Center Frame Label Sensor with Installed in Printer Paper Guide Label Sensor Assembly Replacing the Label Sensor Module Replacing the Head Open Switch Replacing the Display Panel PCB Detach Connectors Remove Screws FactoryResets Small large Factory Settings/Test Print Clear Head Counters Factory mode Clear Dispenser Counter Counter clear Dis Clear Cutter Counter Counter clear cut Clear Eeprom Counter all clear completed All clear mode Large Test Print Small Test Print Sample Test Prints Factory Resets Troubleshooting IEEE1284 Parallel Interface Initial Check List IEEE1284 Parallel Interface Universal Serial BUS USB Lan Ethernet Interface Installation Problems Printer Does Not Come Up Ready Intermittent Problems NetWare Troubleshooting Windows NT/LAN Server Troubleshooting Windows NT/LAN Server Troubleshooting LED Error Signals Print Quality Problems Troubleshooting Tables Print Quality Problems Error LED Print Quality Problems Poor Head Factory DefaultHead Pattern Examples Head Pattern Examples Receive Buffer Hex Dump Hex Dump Diagnostic LabelsPrint Buffer Hex Dump PN 9001078 Rev.B OptionalAccessories Mounting Bracket PAN Head Screws Self Tapping Label Cutter Kit Installation Guillotine Type Remove Front Door Mounting Brackets Remove 2 Screws Strike Plate Label Dispenser InstallationPeel BAR PAN Head Screws Front Door To be Removed Step LH Cover Front DoorRH Cover Raise RH Cover Loosen 2 Inside Screws Holding LH LH Cover Loosen 4 Screws With 2 Self Tapping Horizontal Peel BAR Existing Ribbon Tension Plate Position Ribbon Tension Plate Over Peel BAR Existing Ribbon Remove Ribbon Tension Plate Label Dispenser Installation Front Label RollLabels Idle Roller Label Backing Drive Label Dispenser Spindle by Inserting Over Front Door Magnetic Door Pins 1 & 2 Must be in UPTurn Potentiometer to Adjust Label Taken Sensor Step Head Latch Label Dispenser Pcmcia Memory Expansion Installation Lifting Upwards To Cabinet Holding EXT Connector Optional Accessories Pcmcia Memory Expansion Installation Main PCB Board Showing Where Memory Board will be Installed 37SECURE from Underside of Main PCB Board with Memory PCB Board Main PCB Flash Memory Expansion Installation Indexing Notches Flash Memory Expansion Installation Real Time Clock Installation Rev.B Real Time Clock Installation Factory Reset Procedure Set Calendar Set calendar Yes Rev. B Optional Accessories Spare Parts List Frame Assembly Item no Code Description QTY Plain Washer Print Head Assembly Print Head Assembly Head Frame Head Pressure Bracket Ribbon Assembly Ribbon Assembly Ribbon Assembly Guide Plate B Base Cover Assembly Base Cover Assembly Base Cover Assembly Base Cover Assembly Description QTY Item no Motor Bracket Cable Protector Main PCB Assembly Interface Options Pcmcia Memory Option Cutter Assembly Option Cutter SET Dispenser Assembly Option Dispenser Assembly Option Dispenser Assembly Option Dispense Frame Flange Parts List Index Index-2 Index-3