Units for Voltage and Current |
|
|
|
|
| User Unit #2 – 5 | |||||
|
|
|
|
|
| ||||||
Units for Voltage and Current |
|
|
|
|
| ||||||
Program |
| Utilities | Display Attributes |
| Units for Voltage and | Parameter Type — Selection List | |||||
Current |
|
|
|
|
|
|
|
|
| Factory Default — % | |
|
|
|
|
|
|
|
|
|
| ||
This parameter sets the unit of measurement for current and voltage values | Changeable During Run — Yes | ||||||||||
displayed on the keypad. |
|
|
|
|
| ||||||
|
|
|
|
|
| ||||||
Settings: |
|
|
|
|
|
|
|
|
|
| |
% |
|
|
|
|
|
|
|
|
|
| |
V/A |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |||||
Upper Deviation Limit |
|
|
|
|
|
| |||||
Program |
| Feedback Settings | Upper Deviation Limit | Parameter Type — Numerical | |||||||
This parameter determines the maximum amount that the feedback may | Factory Default — 50.00 | ||||||||||
| |||||||||||
increase the output signal. |
|
|
|
|
| Changeable During Run — Yes | |||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Minimum — 0.00 | |
|
|
|
|
|
|
|
|
|
| Maximum — 50.00 | |
|
|
|
|
|
|
|
|
|
| Units — % | |
|
|
|
|
|
|
| |||||
Upper Limit Frequency |
|
| ⇒ |
|
|
| |||||
| ⇒⇒ |
|
|
|
|
| |||||
Program |
| Fundamental Parameters |
| Fundamental #1 Upper | Parameter Type — Numerical | ||||||
Limit Frequency |
|
|
|
|
|
| Factory Default — 60.0 | ||||
|
|
|
|
|
|
|
|
|
| ||
This parameter sets the highest frequency that the ASD will accept as a | Changeable During Run — Yes | ||||||||||
frequency command or frequency setpoint. The ASD may output frequencies | |||||||||||
| |||||||||||
higher than the Upper Limit Frequency (but, lower than the Maximum | Minimum — 0.0 | ||||||||||
Frequency) when operating in the PID Control mode, Torque Control mode, | Maximum — Max. Freq. | ||||||||||
or the Vector Control modes (sensorless or feedback). | |||||||||||
| |||||||||||
Note: This setting may not be higher than the Maximum | Units — Hz | ||||||||||
| |||||||||||
Frequency setting. | ⇒ |
|
|
|
|
| |||||
| ⇒ |
|
|
|
|
|
|
|
| ||
User Unit #1 |
|
|
|
|
|
|
|
| |||
Program |
| Utilities | Display Attributes |
| User Unit #1 | Parameter Type — | |||||
The displayed unit of measurement may be changed from the Hz default setting | Factory Default — 0.00 | ||||||||||
| |||||||||||
to any of the available characters for the | Changeable During Run — Yes | ||||||||||
|
|
|
|
|
|
|
|
|
| ||
User Unit #2 – #5 may be used to complete the unit of measurement display. |
| ||||||||||
Note: Program |
| Utilitites | Display Attributes | Hz Per User- |
| ||||||
defined Unit must be a |
| ||||||||||
⇒ |
|
| ⇒⇒ |
| |||||||
User Unit #2 – 5 |
|
|
|
| |||||||
Program |
| Utilities | Display Attributes |
| User Unit #2 – #5 |
| |||||
See User Unit #1 for information on this parameter. | ⇒ |
| |||||||||
W7 ASD Installation⇒ | ⇒and⇒Operation⇒Manual |
| ⇒ |
| 133 |