Low Output Disable Start Level |
|
|
|
| Maximum Output Voltage #1 | ||||
|
|
|
| ||||||
Low Output Disable Start Level |
|
|
| ||||||
Program | ⇒ | PID Setup |
| Parameter Type — Numerical | |||||
| ⇒ |
|
|
|
|
| Factory Default — 0.0 | ||
The Low Output Disable Start Level sets the output frequency threshold that, |
| ||||||||
if exceeded, will initiate the LOD function if properly configured. |
| Changeable During Run — Yes | |||||||
|
|
|
|
|
|
|
| Minimum — 0.0 | |
|
|
|
|
|
|
|
| Maximum — Max. Freq. | |
|
|
|
|
|
|
|
| Units — Hz | |
Low Speed Signal Output Frequency |
|
| |||||||
Program |
| Terminal Settings | Output Terminals Low Speed | Parameter Type — Numerical | |||||
Signal Output Frequency |
|
|
|
|
| Factory Default — 0.0 | |||
|
|
|
|
|
|
|
| ||
This parameter sets the |
| Changeable During Run — Yes | |||||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| Minimum — 0.0 | |
|
|
|
|
|
|
|
| Maximum — Upper Limit | |
|
|
|
|
|
|
|
| Units — Hz | |
|
|
|
|
|
|
| |||
Main EEPROM Version |
|
|
|
|
|
| |||
Program |
| Utilities Versions | Main Board EEPROM Version |
| |||||
This is a |
| ||||||||
|
|
|
|
| |||||
Maximum Output Frequency |
|
|
|
| |||||
Program ⇒Fundamental Parameters | Fundamental #1 | Maximum | Parameter Type — Numerical | ||||||
Output Frequency |
|
|
| ⇒⇒ |
| Factory Default — 80.0 | |||
|
|
|
|
| |||||
|
|
|
|
|
|
|
| ||
This setting determines the absolute maximum frequency that the ASD can | Changeable During Run — No | ||||||||
output. This setting is also referred to as FH. |
| ||||||||
|
| ||||||||
Accel/decel⇒times are calculated based⇒ | on the Maximum⇒Frequency setting. | Minimum — 30.0 | |||||||
Note: This setting may not be lower than the Upper Limit setting. | Maximum — 299.0 | ||||||||
| |||||||||
|
|
|
|
|
|
|
| Units — Hz | |
|
|
|
|
| |||||
Maximum Output Voltage #1 |
|
|
|
| |||||
Program |
| Fundamental Parameters | Fundamental #1 | Maximum | Parameter Type — Numerical | ||||
Output Voltage #1 |
|
|
|
|
| Factory Default — (ASD dependent) | |||
|
|
|
|
|
|
|
| ||
This parameter sets the maximum value of the output voltage of the ASD for | Changeable During Run — Yes | ||||||||
the #1 Motor Set. | value,⇒the output voltage cannot be higher than | ||||||||
| |||||||||
Regardless of the programmed⇒ | Minimum — 0.0 | ||||||||
the input voltage. |
|
|
|
|
| Maximum — (ASD dependent) | |||
|
|
|
|
|
|
|
| ||
The actual output voltage will be influenced by the input voltage of the ASD | Units — Volts | ||||||||
and the Supply Voltage Compensation parameter setting. |
| ||||||||
|
| ||||||||
W7 ASD Installation⇒and Operation Manual | ⇒⇒ |
| 83 |