OUT5 Terminal |
|
|
|
| OUT7 Off Delay | ||||
|
|
|
|
|
| ||||
OUT5 Terminal |
|
|
|
|
| ||||
Program | ⇒ | Terminal Settings | ⇒ | Output Terminals |
| OUT5 Terminal | Parameter Type — Selection List | ||
|
|
| ⇒ |
| |||||
Assignment |
|
|
|
| Factory Default — Upper Limit | ||||
This parameter sets the functionality of the OUT5 output contacts to 1 of the 58 | Changeable During Run — No | ||||||||
possible functions that are listed in Table 7 on page 141. |
|
| |||||||
The on and off delay times of the OUT5 contacts may be adjusted to provide |
| ||||||||
more response time to the device that is connected to the output terminals. |
| ||||||||
In addition, the output contacts must be specified as Normally Open or |
| ||||||||
Normally Closed. |
|
|
|
|
| ||||
OUT6 Off Delay |
|
|
|
|
| ||||
Program | ⇒ | Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | ||
Delays |
| ⇒⇒ |
|
| |||||
| OUT6 Off Delay |
|
|
|
| Factory Default — 2.0 | |||
Once the condition is met to change the state of the OUT6 output contacts, this | Changeable During Run — No | ||||||||
parameter delays the response of the contacts by the programmed value (see |
| ||||||||
waveforms at FL Off Delay). |
|
|
|
| Minimum — 2.0 | ||||
The on and off delay times of the OUT6 contacts may be adjusted to provide | Maximum — 200.0 | ||||||||
more response time to the device that is connected to the output terminals. |
| ||||||||
|
|
|
|
|
|
|
| Units — mS | |
OUT6 On Delay |
|
|
|
|
| ||||
Program |
|
| Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | |
Delays |
| OUT6 On Delay |
|
|
|
| Factory Default — 2.0 | ||
|
|
|
|
|
|
|
| ||
This parameter delays the response of the OUT6 output contacts by the | Changeable During Run — No | ||||||||
programmed value (see waveforms at FL On Delay). |
|
| |||||||
|
|
| |||||||
The delay may be increased to prevent relay chatter. |
|
| Minimum — 2.0 | ||||||
|
|
| |||||||
|
|
|
|
|
|
|
| Maximum — 200.0 | |
|
|
|
|
|
|
|
| Units — mS | |
|
|
|
|
|
| ||||
OUT6 Terminal |
|
|
|
|
| ||||
Program⇒ |
| Terminal Settings | ⇒ | Output Terminals |
| OUT6 Terminal | Parameter Type — Selection List | ||
| ⇒ |
|
| ⇒ |
| ||||
Assignment |
|
|
|
| Factory Default — Reach Speed | ||||
This parameter sets the functionality of the OUT6 output contacts to 1 of the 58 | Changeable During Run — No | ||||||||
possible functions that are listed in Table 7 on page 141. |
|
| |||||||
The on and off delay times of the OUT6 contacts may be adjusted to provide |
| ||||||||
more response time to the device that is connected to the output terminals. |
| ||||||||
In addition, the output contacts must be specified as Normally Open or |
| ||||||||
Normally Closed. | ⇒⇒ |
|
| ||||||
⇒ |
|
| |||||||
OUT7 Off Delay |
|
|
| ||||||
Program⇒ |
| Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | ||
Delays |
| OUT7 Off Delay |
|
|
|
| Factory Default — 2.0 | ||
|
|
|
|
|
|
|
| ||
Once the condition is met to change the state of the OUT7 output contacts, this | Changeable During Run — No | ||||||||
parameter delays the response of the contacts by the programmed value (see | |||||||||
| |||||||||
waveforms at FL Off Delay). |
|
|
|
| Minimum — 2.0 | ||||
The on and off delay times of the OUT7 contacts may be adjusted to provide | Maximum — 200.0 | ||||||||
more response time to the device that is connected to the output terminals. | |||||||||
| |||||||||
W7 ASD Installation⇒⇒and Operation⇒⇒Manual |
| Units — mS | |||||||
| 91 |