OUT4 Off Delay |
|
|
|
| OUT5 On Delay | |||||
|
|
|
|
|
|
| ||||
| OUT4 Off Delay |
|
|
|
|
| ||||
| Program | ⇒ | Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | ||
| Delays |
|
| ⇒⇒ |
|
| ||||
|
|
| OUT4 Off Delay |
|
|
|
| Factory Default — 2.0 | ||
| Once the condition is met to change the state of the OUT4 output contacts, this | Changeable During Run — No | ||||||||
| parameter delays the response of the contacts by the programmed value (see |
| ||||||||
| waveforms at FL Off Delay). |
|
|
|
| Minimum — 2.0 | ||||
| The on and off delay times of the OUT4 contacts may be adjusted to provide | Maximum — 200.0 | ||||||||
| more response time to the device that is connected to the output terminals. |
| ||||||||
|
|
|
|
|
|
|
|
|
| Units — mS |
| OUT4 On Delay |
|
|
|
|
| ||||
| Program | ⇒ | Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | ||
| Delays |
|
| ⇒⇒ |
|
| ||||
|
|
| OUT4 On Delay |
|
|
|
| Factory Default — 2.0 | ||
| This parameter delays the response of the OUT4 output contacts by the | Changeable During Run — No | ||||||||
| programmed value (see waveforms at FL On Delay). |
|
|
| ||||||
| The delay may be increased to prevent relay chatter. |
|
| Minimum — 2.0 | ||||||
|
|
|
|
|
|
|
|
|
| Maximum — 200.0 |
|
|
|
|
|
|
|
|
|
| Units — mS |
| OUT4 Terminal |
|
|
|
|
| ||||
| Program⇒ |
| Terminal Settings | ⇒ | Output Terminals |
| OUT4 Terminal | Parameter Type — Selection List | ||
|
|
| ⇒ |
|
| ⇒ |
| |||
| Assignment |
|
|
|
| Factory Default — Lower Limit | ||||
| This parameter sets the functionality of the OUT4 output contacts to 1 of the 58 | Changeable During Run — No | ||||||||
| possible functions that are listed in Table 7 on page 141. |
|
| |||||||
| The on and off delay times of the OUT4 contacts may be adjusted to provide |
| ||||||||
| more response time to the device that is connected to the output terminals. |
| ||||||||
| In addition, the output contacts must be specified as Normally Open or |
| ||||||||
| Normally Closed. |
|
|
|
|
| ||||
| OUT5 Off Delay |
|
|
|
|
| ||||
| Program⇒ |
| Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | ||
| Delays |
| ⇒ |
| ⇒⇒ |
|
| |||
|
|
| OUT5 Off Delay |
|
|
|
| Factory Default — 2.0 | ||
| Once the condition is met to change the state of the OUT5 output contacts, this | Changeable During Run — No | ||||||||
| parameter delays the response of the contacts by the programmed value (see |
| ||||||||
| waveforms at FL Off Delay). |
|
|
|
| Minimum — 2.0 | ||||
| The on and off delay times of the OUT5 contacts may be adjusted to provide | Maximum — 200.0 | ||||||||
| more response time to the device that is connected to the output terminals. |
| ||||||||
|
|
|
|
|
|
|
|
|
| Units — mS |
| OUT5 On Delay |
|
|
|
|
| ||||
| Program |
|
| Terminal Settings |
| Terminal Delays |
| Output Terminal | Parameter Type — Numerical | |
| Delays |
|
| OUT5 On Delay |
|
|
|
| Factory Default — 2.0 | |
|
|
|
|
|
|
|
|
|
| |
| This parameter delays the response of the OUT5 output contacts by the | Changeable During Run — No | ||||||||
| programmed value (see waveforms at FL On Delay). |
|
| |||||||
|
|
|
| |||||||
| The delay may be increased to prevent relay chatter. |
|
| Minimum — 2.0 | ||||||
|
|
|
| |||||||
|
| ⇒⇒ |
| ⇒⇒ |
| Maximum — 200.0 | ||||
|
|
|
| Units — mS | ||||||
90 |
|
|
| W7 ASD Installation and Operation Manual |