Schneider Electric 4000 manual 142

Appendix A—Abbreviated Register Listing	63230-300-212
Register Listing	April 2001

Table A–3:Abbreviated Register List

Register	Description	Scale	Units	Register Range
Number		Factor
1601	Maximum THD/thd Current, Phase B	—	0.10%	0 to 32,767
1602	Maximum THD/thd Current, Phase C	—	0.10%	0 to 32,767
1603	Maximum THD/thd Current, Phase N	—	0.10%	0 to 32,767
1604	Maximum THD/thd Current, Ground	—	0.10%	0 to 32,767
1607	Maximum THD/thd Voltage, Phase A-N	—	0.10%	0 to 32,767
1608	Maximum THD/thd Voltage, Phase B-N	—	0.10%	0 to 32,767
1609	Maximum THD/thd Voltage, Phase C-N	—	0.10%	0 to 32,767
1610	Maximum THD/thd Voltage, Phase N-G	—	0.10%	0 to 32,767 ￿
1611	Maximum THD/thd Voltage, Phase A-B	—	0.10%	0 to 32,767
1612	Maximum THD/thd Voltage, Phase B-C	—	0.10%	0 to 32,767
1613	Maximum THD/thd Voltage, Phase C-A	—	0.10%	0 to 32,767
1618	Maximum Current K-Factor, Phase A	—	0.10	0 to 10,000
1619	Maximum Current K-Factor, Phase B	—	0.10	0 to 10,000
1620	Maximum Current K-Factor, Phase C	—	0.10	0 to 10,000
1621	Maximum Crest Factor, Current, Phase A	—	0.01	0 to 10,000
1622	Maximum Crest Factor, Current, Phase B	—	0.01	0 to 10,000
1623	Maximum Crest Factor, Current, Phase C	—	0.01	0 to 10,000
1624	Maximum Crest Factor, Current, Neutral	—	0.01	0 to 10,000
1625	Maximum Crest Factor, Voltage A-N/A-B	—	0.01	0 to 10,000 ￿
1626	Maximum Crest Factor, Voltage B-N/B-C	—	0.01	0 to 10,000
1627	Maximum Crest Factor, Voltage C-N/C-A	—	0.01	0 to 10,000
1630	Maximum Current Fundamental RMS Magnitude, Phase A	A	Amps/Scale	0 to 32,767
1631	Maximum Current Fundamental Coincident Angle, Phase A	—	0.1 °	0 to 3,599
1632	Maximum Current Fundamental RMS Magnitude, Phase B	A	Amps/Scale	0 to 32,767
1633	Maximum Current Fundamental Coincident Angle, Phase B	—	0.1 °	0 to 3,599
1634	Maximum Current Fundamental RMS Magnitude, Phase C	A	Amps/Scale	0 to 32,767
1635	Maximum Current Fundamental Coincident Angle, Phase C	—	0.1 °	0 to 3,599
1636	Maximum Current Fundamental RMS Magnitude, Neutral	B	Amps/Scale	0 to 32,767
1637	Maximum Current Fundamental Coincident Angle, Neutral	—	0.1 °	0 to 3,599
1638	Maximum Current Fundamental RMS Magnitude, Ground	C	Amps/Scale	0 to 32,767 ￿
1639	Maximum Current Fundamental Coincident Angle, Ground	—	0.1 °	0 to 3,599 ￿
1644	Maximum Voltage Fundamental RMS Magnitude, A-N/A-B	D	Volts/Scale	0 to 32,767
1645	Maximum Voltage Fundamental Coincident Angle, A-N/A-B	—	0.1 °	0 to 3,599
1646	Maximum Voltage Fundamental RMS Magnitude, B-N/B-C	D	Volts/Scale	0 to 32,767
1647	Maximum Voltage Fundamental Coincident Angle, B-N/B-C	—	0.1 °	0 to 3,599
1648	Maximum Voltage Fundamental RMS Magnitude, C-N/C-A	D	Volts/Scale	0 to 32,767

See “How Power Factor is Stored in the Register” on page 128.

The alternate storage method for power factor (PF) is useful for outputting PF on analog outputs. The PF value is stored as a positive value between 0 and 2, centered around 1 (unity). A value of 0 lagging maps to 0; -0.999 maps to 0.999;0.999 leading maps to 1.001; and 0 leading maps to 2. The alternate PF is also stored with a scale factor 0.001.

These configuration registers require that you enter the setup mode to change the register’s contents. Issue command 9020 to enter setup mode and 9021 to exit setup mode. See “Using the Command Interface to Change Configuration Registers” on page 187 for instructions on

￿how to use the setup-mode commands.

Quantity available for 4-wire system only. Value set to -32,768 if not available.

142 © 2001 Schneider Electric All Rights Reserved