Schneider Electric 4000 manual 143

63230-300-212	Appendix A—Abbreviated Register Listing
April 2001	Register Listing

Table A–3:Abbreviated Register List

Register	Description	Scale	Units	Register Range
Number		Factor
1649	Maximum Voltage Fundamental Coincident Angle, C-N/C-A	—	0.1 °	0 to 3,599
1650	Maximum Voltage Fundamental RMS Magnitude, N-G	E	Volts/Scale	0 to 32,767
1651	Maximum Voltage Fund. Coincident Angle, N-G	—	0.1 °	0 to 3,599 ￿
1655	Maximum Fundamental Real Power, Phase A	F	kW/Scale	-32,767 to ￿32,767
1656	Maximum Fundamental Real Power, Phase B	F	kW/Scale	-32,767 to 32,767
1657	Maximum Fundamental Real Power, Phase C	F	kW/Scale	-32,767 to 32,767
1658	Maximum Fundamental Real Power, Total	F	kW/Scale	-32,767 to 32,767
1659	Maximum Fundamental Reactive Power, Phase A	F	kVA/Scale	-32,767 to 32,767
1660	Maximum Fundamental Reactive Power, Phase B	F	kVA/Scale	-32,767 to 32,767
1661	Maximum Fundamental Reactive Power, Phase C	F	kVA/Scale	-32,767 to 32,767
1662	Maximum Fundamental Reactive Power, Total	F	kVA/Scale	-32,767 to 32,767
1664	Maximum Distortion Power, Phase A	F	kW/Scale	-32,767 to 32,767
1665	Maximum Distortion Power, Phase B	F	kW/Scale	-32,767 to 32,767
1666	Maximum Distortion Power, Phase C	F	kW/Scale	-32,767 to 32,767 ￿
1667	Maximum Distortion Power, Total	F	kW/Scale	-32,767 to 32,767
1668	Maximum Distortion Factor, Phase A	F	0.10	0 to 1,000
1669	Maximum Distortion Factor, Phase B	F	0.10	0 to 1,000
1670	Maximum Distortion Factor, Phase C	F	0.10	0 to 1,000 ￿
1671	Maximum Distortion Factor, Total	F	0.10	0 to 1,000
1674	Maximum Harmonic Current, Phase A	A	Amps/Scale	0 to 32,767
1675	Maximum Harmonic Current, Phase B	A	Amps/Scale	0 to 32,767
1676	Maximum Harmonic Current, Phase C	A	Amps/Scale	0 to 32,767
1677	Maximum Harmonic Current, Neutral	B	Amps/Scale	0 to 32,767
1678	Maximum Harmonic Voltage, A-N	D	Volts/Scale	0 to 32,767
1679	Maximum Harmonic Voltage, B-N	D	Volts/Scale	0 to 32,767
1680	Maximum Harmonic Voltage, C-N	D	Volts/Scale	0 to 32,767 ￿
1681	Maximum Total Demand Distortion	—	0.01	0 to 10,000
1684	Maximum Current, Positive Sequence, Magnitude	A	Amps/Scale	0 to 32,767
1685	Maximum Current, Positive Sequence, Angle	—	0.1	0 to 3,599
1686	Maximum Current, Negative Sequence, Magnitude	A	Amps/Scale	0 to 32,767
1687	Maximum Current, Negative Sequence, Angle	—	0.1	0 to 3,599
1688	Maximum Current, Zero Sequence, Magnitude	A	Amps/Scale	0 to 32,767
1689	Maximum Current, Zero Sequence, Angle	—	0.1	0 to 3,599
1690	Maximum Voltage, Positive Sequence, Magnitude	D	Volts/Scale	0 to 32,767
1691	Maximum Voltage, Positive Sequence, Angle	—	0.1	0 to 3,599
1692	Maximum Voltage, Negative Sequence, Magnitude	D	Volts/Scale	0 to 32,767

See “How Power Factor is Stored in the Register” on page 128.

The alternate storage method for power factor (PF) is useful for outputting PF on analog outputs. The PF value is stored as a positive value between 0 and 2, centered around 1 (unity). A value of 0 lagging maps to 0; -0.999 maps to 0.999;0.999 leading maps to 1.001; and 0 leading maps to 2. The alternate PF is also stored with a scale factor 0.001.

These configuration registers require that you enter the setup mode to change the register’s contents. Issue command 9020 to enter setup mode and 9021 to exit setup mode. See “Using the Command Interface to Change Configuration Registers” on page 187 for instructions on

￿how to use the setup-mode commands.

Quantity available for 4-wire system only. Value set to -32,768 if not available.

© 2001 Schneider Electric All Rights Reserved 143