Schneider Electric 4000 manual 137

63230-300-212	Appendix A—Abbreviated Register Listing
April 2001	Register Listing

Table A–3:Abbreviated Register List

Register	Description	Scale	Units	Register Range
Number		Factor
1372	Minimum Alternate Displacement Power Factor, Phase A	—	0.001	0 to 2,000
1373	Minimum Alternate Displacement Power Factor, Phase B	—	0.001	0 to 2,000
1374	Minimum Alternate Displacement Power Factor, Phase C	—	0.001	0 to 2,000	￿
1375	Minimum Alternate Displacement Power Factor, Total	—	0.001	0 to 2,000 ￿
1380	Minimum Frequency	—	0.01 Hertz	(50/60) 2,300 to 6,700
			0.1 Hertz	(400) 3,500 to 4,500
1381	Minimum Temperature	—	0.1 °C	-1,000 to 1,000
1390	Minimum Auxiliary Analog Input Value, User-Selected Input 1	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1391	Minimum Auxiliary Analog Input Value, User-Selected Input 2	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1392	Minimum Auxiliary Analog Input Value, User-Selected Input 3	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1393	Minimum Auxiliary Analog Input Value, User-Selected Input 4	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1394	Minimum Auxiliary Analog Input Value, User-Selected Input 5	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1395	Minimum Auxiliary Analog Input Value, User-Selected Input 6	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1396	Minimum Auxiliary Analog Input Value, User-Selected Input 7	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1397	Minimum Auxiliary Analog Input Value, User-Selected Input 8	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1398	Minimum Auxiliary Analog Input Value, User-Selected Input 9	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1399	Minimum Auxiliary Analog Input Value, User-Selected Input 10	—	Refer to Analog Input	-32,767 to 32,767
			Setup
1400	Minimum THD/thd Current, Phase A	—	0.10%	0 to 32,767
1401	Minimum THD/thd Current, Phase B	—	0.10%	0 to 32,767
1402	Minimum THD/thd Current, Phase C	—	0.10%	0 to 32,767
1403	Minimum THD/thd Current, Phase N	—	0.10%	0 to 32,767
1404	Minimum THD/thd Current, Ground	—	0.10%	0 to 32,767
1407	Minimum THD/thd Voltage, A-N	—	0.10%	0 to 32,767
1408	Minimum THD/thd Voltage, B-N	—	0.10%	0 to 32,767
1409	Minimum THD/thd Voltage, C-N	—	0.10%	0 to 32,767
1410	Minimum THD/thd Voltage, N-G	—	0.10%	0 to 32,767
1411	Minimum THD/thd Voltage, A-B	—	0.10%	0 to 32,767	￿
1412	Minimum THD/thd Voltage, B-C	—	0.10%	0 to 32,767
1413	Minimum THD/thd Voltage, C-A	—	0.10%	0 to 32,767
1418	Minimum Current K-Factor, Phase A	—	0.10	0 to 10,000

See “How Power Factor is Stored in the Register” on page 128.

The alternate storage method for power factor (PF) is useful for outputting PF on analog outputs. The PF value is stored as a positive value between 0 and 2, centered around 1 (unity). A value of 0 lagging maps to 0; -0.999 maps to 0.999;0.999 leading maps to 1.001; and 0 leading maps to 2. The alternate PF is also stored with a scale factor 0.001.

These configuration registers require that you enter the setup mode to change the register’s contents. Issue command 9020 to enter setup mode and 9021 to exit setup mode. See “Using the Command Interface to Change Configuration Registers” on page 187 for instructions on

￿how to use the setup-mode commands.

Quantity available for 4-wire system only. Value set to -32,768 if not available.

© 2001 Schneider Electric All Rights Reserved 137