Schneider Electric 4000 manual Real to Time Minimum Metered Values, 135

© 2001 Schneider Electric All Rights Reserved

63230-300-212	Appendix A—Abbreviated Register Listing
April 2001	Register Listing

Table A–3:Abbreviated Register List

Register	Description	Scale	Units	Register Range
Number		Factor
1277	Harmonic Current, Neutral	B	Amps/Scale	0 to 32,767
1278	Harmonic Voltage, A-N/A-B	D	Volts/Scale	0 to 32,767 ￿
1279	Harmonic Voltage, B-N/B-C	D	Volts/Scale	0 to 32,767
1280	Harmonic Voltage, C-N/C-A	D	Volts/Scale	0 to 32,767
1281	Total Demand Distortion	—	0.1%	0 to 1,000
1284	Current, Positive Sequence, Magnitude	A	Amps/Scale	0 to 32,767
1285	Current, Positive Sequence, Angle	—	0.1°	0 to 3,599
1286	Current, Negative Sequence, Magnitude	A	Amps/Scale	0 to 32,767
1287	Current, Negative Sequence, Angle	—	0.1°	0 to 3,599
1288	Current, Zero Sequence, Magnitude	A	Amps/Scale	0 to 32,767
1289	Current, Zero Sequence, Angle	—	0.1°	0 to 3,599
1290	Voltage, Positive Sequence, Magnitude	D	Volts/Scale	0 to 32,767
1291	Voltage, Positive Sequence, Angle	—	0.1°	0 to 3,599
1292	Voltage, Negative Sequence, Magnitude	D	Volts/Scale	0 to 32,767
1293	Voltage, Negative Sequence, Angle	—	0.1°	0 to 3,599
1294	Voltage, Zero Sequence, Magnitude	D	Volts/Scale	0 to 32,767
1295	Voltage, Zero Sequence, Angle	—	0.1°	0 to 3,599
1296	Current, Sequence, Unbalance	—	0.10%	0 to 32,767
1297	Voltage, Sequence, Unbalance	—	0.10%	0 to 32,767
Real to Time Minimum Metered Values
1300	Minimum Current, Phase A	A	Amps/Scale	0 to 32,767
1301	Minimum Current, Phase B	A	Amps/Scale	0 to 32,767
1302	Minimum Current, Phase C	A	Amps/Scale	0 to 32,767
1303	Minimum Current, Neutral	B	Amps/Scale	0 to 32,767
1304	Minimum Current, Ground	C	Amps/Scale	0 to 32,767 ￿
1305	Minimum Current, 3-Phase Average	A	Amps/Scale	0 to 32,767
1306	Minimum Current, Apparent RMS	A	Amps/Scale	0 to 32,767
1307	Minimum Current Unbalance, Phase A	—	0.10%	-1,000 to 1,000
1308	Minimum Current Unbalance, Phase B	—	0.10%	-1,000 to 1,000
1309	Minimum Current Unbalance, Phase C	—	0.10%	-1,000 to 1,000
1310	Minimum Current Unbalance, Max	—	0.10%	-1,000 to 1,000
1320	Minimum Voltage, A-B	D	Volts/Scale	0 to 32,767
1321	Minimum Voltage, B-C	D	Volts/Scale	0 to 32,767
1322	Minimum Voltage, C-A	D	Volts/Scale	0 to 32,767
1323	Minimum Voltage, L-L Average	D	Volts/Scale	0 to 32,767
1324	Minimum Voltage, A-N	D	Volts/Scale	0 to 32,767

See “How Power Factor is Stored in the Register” on page 128.

The alternate storage method for power factor (PF) is useful for outputting PF on analog outputs. The PF value is stored as a positive value between 0 and 2, centered around 1 (unity). A value of 0 lagging maps to 0; -0.999 maps to 0.999;0.999 leading maps to 1.001; and 0 leading maps to 2. The alternate PF is also stored with a scale factor 0.001.

These configuration registers require that you enter the setup mode to change the register’s contents. Issue command 9020 to enter setup mode and 9021 to exit setup mode. See “Using the Command Interface to Change Configuration Registers” on page 187 for instructions on

￿how to use the setup-mode commands.

Quantity available for 4-wire system only. Value set to -32,768 if not available.￿

135