Meter, 3Ø4W3CT | Schneider Electric 4000 specs

Chapter 3—Operation	63230-300-212
Configuring the Circuit Monitor Using The Setup Menu	April 2001

Table 3–2: Options for Communications Setup

Parity

Even, Odd, or None

Parity at which the circuit monitor will communicate.

Even

Ethernet Communications Card (ECC) Setup

Ethernet communications is available only if you have an optional Ethernet Communications Card (ECC) that fits into slot A on the top of the circuit monitor. See “Option Cards” on page 28 in Chapter 4—Installationof the installation manual for more information. To set up the Ethernet communications between the circuit monitor and the network, refer to instruction bulletin no. 63230-304-200 provided with the ECC.

Setting Up the Metering Functions of the Circuit Monitor

To set up the metering within the circuit monitor, you must configure the following items on the Meter setup screen for basic setup:

•CT and PT ratios

•System type

•Frequency

The power demand method, interval and subinterval, and advanced setup options are also accessible from the Meter Setup menu, but are not required for basic setup if you are accepting the factory defaults already defined in the circuit monitor. Follow these steps to set up the circuit monitor:

1.From the Main Menu, select Setup > Meter.

The Meter setup screen displays. Table 3–3describes the options on this menu.

METER
Ø CT Primary		5
Ø CT Secondary		5
N CT Primary		5
N CT Secondary		5
PT Pri Scale		x1
PT Primary		120
PT Secondary		120
Sys Type	3Ø4W3CT
Frequency (Hz)		60
Pwr Dmd Meth	Slide
Pwr Dmd Int		15
Pwr Dmd Sub Int		1
Advanced

Required for basic setup

2.Use the arrow buttons to scroll to the menu option you want to change.

3.Press the enter button to select the value. The value begins to blink. Use the arrow buttons to scroll through the available values. Then, press the enter button to select the new value.

4.Use the arrow buttons to scroll through the other options on the menu, or if you are finished, press the menu button to save.

16	© 2001 Schneider Electric All Rights Reserved

Image 28

Schneider Electric 4000 manual Setting Up the Metering Functions of the Circuit Monitor, 3Ø4W3CT

Contents

April Retain for future use Please Note Class a FCC Statement Contents Running the Diagnostics Wiring Error Test Power Factor Min/Max Conventions VAR Sign ConventionsWire Pulse Initiator Analog Input Example Logging AlarmsWaveform and Event Capture Appendix B-USING the Command Interface Disturbance Monitoring Glossary Index Schneider Electric All Rights Reserved List of Figures Figure A-1 Bits in a register 128 List of Figures 63230-300-212 April Viii List of Tables Summary of Circuit Monitor Instrumentation List of Tables 63230-300-212 April Chapter Contents Introduction What is the Circuit MONITOR? Advanced featuresFrom the display or remotely using software. -1summarizes Readings available from the circuit monitor Accessories and Options for the Circuit Monitor Circuit Monitor Parts, Accessories, and Custom Cables63230-300-212 Introduction April Description Part Number Document Number Topics not Covered FeaturesThis Bulletin Firmware Introduction FirmwAre Introduction 63230-300-212 FirmwAre April Safety Precautions Safety Precautions 63230-300-212 April Advanced features not accessible from the display Operation Meters Resets Min/Max Setup View Alarms Diagnostics Operating the DisplayMain Menu How the Buttons Work Display Menu Conventions DisplayLanguage English Date MM/DD/YYYY Main Menu Overview Operation 63230-300-212 Main Menu Overview April Setting Up the Display Configuring the Circuit Monitor Using the Setup Menu63230-300-212 Operation April Factory Defaults for the Display Settings Setting Up the Communications Communications Options for Communications SetupInfrared Port Setting Up the Metering Functions of the Circuit Monitor Ethernet Communications Card ECC SetupMeter 3Ø4W3CT Options for Meter Setup 3Ø4W4CT2PT Alarm from the display Setting Up AlarmsOperation 63230-300-212 Create the custom alarm Setup and enable the new alarmPerforming two steps Create Custom Alarm Parameters Options for Creating an AlarmLbl Over THD Vbc Type Val Qty THD From the Main Menu, select Setup Alarm Edit Parameters Follow these instructions to set up or edit an alarmDropout setpoints Options for Editing an Alarm Setting Up I/Os SetupDate & Time Display Communications Meter Alarm Passwords KYZ Extender Setup IOX Select ModulesCustom DI120AC Configuring I/O Modules DescriptionsOutputs for the I/O module you selected Name Description IOX Custom Setup I/O Extender Setup selection menu displaysInput/Output Capabilities on Passwords Setting Up PasswordsSetup Diagnostics Engy/Dmd Reset Min/Max Reset Advanced Setup Features Creating Custom Quantities to be Displayed Custom Quant Setup Select Display Display Setup menu displaysSelect a custom quantity Option Available Values Default Options for Custom Quantities Custom Screen Setup Select Custom Screen Custom Screen Setup screen displays28 for instructions Screen Screen Blank LineMonthly Energy Cost Blank Line Screen Monthly Energy Cost Blank Line Available Default Quantities Quantity Type Q Label Q Viewing Custom Screens Advanced Meter Setup Monthly Energy Cost Dollars Select Meter Meter Setup screen displays Advanced Meter Setup 10 Options for Advanced Meter Setup ABC Resetting MIN/MAX, DEMAND, and Energy Values Main Menu ResetsReset Energy Reset Demand Reset MIN/MAX Accumulated Power Demand Min/Max Amp Demand Viewing Metered Data Menus where you can view metered data in real timeOperation 63230-300-212 Viewing Metered Data April Current Voltage Frequency Power Power Factor Viewing Minimum and Maximum Values from the Min/Max MenuMIN/MAX Current a Mn 01/22/2000159A Mx 01/22/2000815A Viewing Alarms Meters Min/Max View Alarms Display Resets Setup DiagnosticsView Alarms Active Alarms List High Priority Log Viewing Active Alarms Active Alarms List 1/1View and Acknowledging High Priority Alarms High Priority Alarms Digital Inputs Analog Inputs Digital Outputs Analog Outputs Viewing I/O StatusDigital Outputs Kyzoff Diagnostics Reading and Writing RegistersREAD/WRITE Regs Reg Hex Dec 1003 000A Performing a Wiring Error Test 10 Wiring Error Test option on the Diagnostics menu Running the Diagnostics Wiring Error Test Meter Information Perform Test 12 Wiring Error Messages Message Description I2 load current less than 1% CT Operation 63230-300-212 Performing a Wiring Check April Metering Capabilities Circuit monitor REAL-TIME Readings MoreReadings One-Second, Real-Time Readings Samples 100 ms Real-Time Readings MIN/MAX Values for REAL-TIME Readings63230-300-212 Metering Capabilities April Power Factor Min/Max Conventions Included with the softwareTo +0 on the same scale Positive in this case Convention, refer to Advanced Meter Setup on Reactive PowerReal ALT CM1 VAR Sign Convention IEEE/IEC VAR Sign Convention Demand Readings Demand readings and their reportable rangesDemand Readings Metering Capabilities 63230-300-212 Demand Readings April April Demand Readings Demand Power Calculation MethodsBlock Interval Demand Block Interval Demand Examples Demand Current Demand VoltageBlock Interval Demand on April Demand Readings Synchronized Demand Minutes for illustration purposes Thermal DemandInterval Peak Demand Generic Demand Input Pulse Demand Metering Channel pulse metering example For all channels Energy Readings Energy ReadingsSee Appendix A-Abbreviated Register Listing on page 127 for Real Power April Energy Readings Power Analysis Values On page 68 summarizes the power analysis valuesHarmonic distortion 100% Harmonic Power = Overall Power April Power Analysis Values Power Analysis Values Value Reportable Range INPUT/OUTPUT Capabilities On page 3 of this bulletin Options I /O Extender OptionsInput/Output Capabilities 63230-300-212 Options April Extender Options Command interface Digital Inputs Demand Synch Pulse Input 59 in -Metering Capabilities for more about demandCalculations To verify peak demand charges Maximum value for each analog input Analog Inputs63230-300-212 Input/Output Capabilities April Analog Inputs Has been configured as follows Analog Input ExampleSample register readings for analog inputs Input/Output Capabilities 63230-300-212 Analog Inputs April Relay Output Operating Modes NormalLatched April Relay Output Operating Modes End Of Power Demand Interval TimedAbsolute kWh Pulse Absolute kVARh Pulse Mechanical Relay Outputs SOLID-STATE KYZ Pulse Output Setpoint-controlled Relay Functions Wire Pulse Initiator Application Calculating the KILOWATTHOUR-PER-PULSE Value Analog Outputs Sample register readings for analog output Analog Output ExampleRegister Reading kW Output Current mA Alarms Alarms Groups About AlarmsAlarms 63230-300-212 About Alarms April Setpoint-Driven Alarms Define the following informationPickup Setpoint Seconds, 100 ms increments, or cycles Alarm Period Pickup Delay Dropout DelayPickup Setpoint Dropout Setpoint Priorities Alarm Levels Alarms About Alarms Custom Alarms SETPOINT-CONTROLLED Relay Functions Alarms 63230-300-212 Custom Alarms April 63230-300-212 Alarms April Types of Setpoint-Controlled Relay FunctionsUndervoltage Overvoltage Phase Loss-Current Phase Loss-VoltageReverse Power Phase Reversal Settings Scale Factors on page 191 in Appendix B-Using the CommandScale Factors Setpoint Scaling Alarm Setpoints Alarms 63230-300-212 Scaling Alarm Setpoints AprilScale groups and their register numbers Scale Group Register Numbers Alarm Conditions and Alarm Numbers List of Default Alarms by Alarm Number Alarm Alarm Description Abbreviated Test Units ScaleStandard Speed Alarms 1 Second Display Name Register Display Name High Speed Alarms 100 msDisturbance Monitoring 1/2 Cycle Digital Alarm TypesType Description Operation Standard Speed Type Description Operation High Speed Disturbance Boolean Alarm Log Storage 100 See Factory Defaults on page 11 of the installation manual102 Alarm Log Storage Alarm LOGData Logs April Data Logs 101 MIN/MAX Logs Min/Max Log Interval Min/Max/Average LogLogging 63230-300-212 Min/Max Logs April 102 Maintenance LOG Values Stored in Maintenance LogApril Maintenance Log Interval Min/Max/Average Log Storage Value Stored Description Logging Memory Allocation Memory Allocation104 Memory allocation in SMS 105 Logging 63230-300-212 Memory Allocation April 106 107 107 Available Resolutions for Disturbance Waveform Captures Types of Waveform CapturesSteady-state Waveform Capture Disturbance Waveform Capture Available Resolutions for Adaptive Waveform Captures Samples per Cycle Max. Duration ResolutionAdaptive Waveform Capture 109 100ms rms Quantities 100ms rms Event Recording110 Setting UP the Circuit Monitor for Automatic Event Capture Waveform Storage63230-300-212 Waveform and Event Capture April 111 HOW the Circuit Monitor Captures AN Event 112 Using SMS to gather data when a disturbance event occurs 113114 113 About Disturbance Monitoring April About Disturbance Monitoring 115 116 Operate any output relays when the event is detected Capabilities of the Circuit Monitor During AN Event63230-300-212 Disturbance Monitoring April Categories CM-4000 Onboard Alarms/Events tab Onboard Files tab April Understanding the Alarm Log Understanding the Alarm LOG119 Schneider Electric All Rights Reserved Monitor 121Upgrading Memory in the Circuit Monitor 123 124 122 Circuit Monitor Memory Upgrading Memory in the Circuit MonitorApril Circuit Monitor Memory 123 Identifying the Firmware Version Meter InformationXxxxxxxx DOM Information in -1 describes potential problems and their TroubleshootingRepresentative for assistance Maintenance and Troubleshooting 63230-300-212 April 126 April Contents About Registers127 Currents and voltages HOW Power Factor is Stored in the Register 128 Table A-1Date and Time Format HOW Date and Time are Stored in the RegisterTable A-2Date and Time Byte Example Register Listing Table A-3Abbreviated Register List April Register Listing Register Description Scale Units Register Range NumberSecond Real-Time Readings 131 132 133 134 Real to Time Minimum Metered Values 135 136 137 138 Real to Time Maximum Metered Values 139 140 To 32,767 See How Power Factor is Stored in the Register on 141 142 143 Accumulated Energy 144 Demand 145 146 147 148 149 150 151 152 153 154 155 System Configuration Phase Extremes156 Current and Voltage Module Configuration 157 = Cvmt 158 Metering Configuration 159 160 161 162 163 164 165 Table A-4Abbreviated Register List for I/O Status Register Name Units Range Description Number 167 Digital Input Template Digital Output Template 169 KWH Analog Output Template Analog Input Template171 First digit 4 indicates point is analog output Table A-5Registers for Alarm Position Counters 173 174 175 176 177 Table A-6Spectral Components Register Description Units Range NumberTemplate 178 179 180 Issuing Commands 183 Point Numbers Various operations181 181 Table B- 1 Location of the command interface Overview of the Command Interface182 Issuing Commands Write the command code to command interface registerTable B- 2 Command Codes 8001-15 Resets April Overview of the Command Interface SetupFiles 185 Point Numbers 186 63230-300-212 Appendix B-Using the Command Interface April 187 Conditional Energy Command Interface Control Digital Input Control188 Using Incremental Energy Incremental EnergyApril Incremental Energy 189 Table B- 3 Registers for Harmonic Calculations Setting UP Individual Harmonic Calculations190 Changing Scale Factors Schneider Electric All Rights Reserved Glossary 193 Glossary 63230-300-212 April Potential transformer PT-also known as a194 Voltage transformer VT-seepotential True power factor-seepower factor195 Glossary 63230-300-212 April 196 INDEXNumerics 197 Index 63230-300-212 April 198 PLC 199 SMS 200 201 Index 63230-300-212 April 202 Page PBG 1M 4/2001