Schneider Electric 4000 manual Digital Output Template, 169

63230-300-212	Appendix A—Abbreviated Register Listing
April 2001	Register Listing

Table A–4:Abbreviated Register List for I/O Status

Register	Name	Units	Range	Description
Number
				Bitmap indicting Demand System(s) to which input is assigned.
				(Default = 0x003F)
				Bit 00 = Power Demand
				Bit 01 = Current Demand
				Bit 02 = Voltage Demand
	Demand Interval Sync		0x0000 to	Bit 03 = Input Metering Demand
Base + 10		—		Bit 04 = Generic Demand 1
	System Assignments		0x003F
				Bit 05 = Generic Demand 2
				Only one Demand Sync Pulse per Demand System is allowed. If
				the user attempts to configure more than one input for each system,
				the lowest IO Point Number will take precedence. The
				corresponding bits of the other points will be set to 0.
Base + 11	Digital Input Options	—	0x0000 to	Bitmap of digital Input Options. (Default = 0)
			0x0001	Bit 00 = Debounce time (0 = 5msec, 1 = 50msec)
				Bitmap indicting metering pulse channel(s) to which input is
				assigned. (Default = 0)
				Bit 00 = Channel 1
				Bit 01 = Channel 2
				Bit 02 = Channel 3
Base + 14	Metering Pulse	—	0x0000 to	Bit 03 = Channel 4
	Channel Assignments		0x03FF	Bit 04 = Channel 5
				Bit 05 = Channel 6
				Bit 06 = Channel 7
				Bit 07 = Channel 8
				Bit 08 = Channel 9
				Bit 09 = Channel 10
Base + 15	Metering Pulse	1.0	1- 32,767	Pulse weight associated with the change of state of the input. Used
	Weight, Demand			for demand metering. (Default = 1)
Base + 16	Metering Pulse Scale	1.0	-3 to 3	Pulse weight scale factor (power of 10) to apply to metering pulse
	Factor, Demand			weight. Used for demand metering. (Default = 0)
Base + 17	Metering Pulse	1.0	1- 32,767	Pulse weight associated with the change of state of the input. Used
	Weight, Consumption			for consumption metering. (Default = 1)
Base + 18￿	Metering Pulse Scale	1.0	-3 to 3	Pulse weight scale factor (power of 10) to apply to metering pulse
	Factor, Consumption			weight. Used for consumption metering. (Default = 0)
				IO Point Diagnostic Bitmap:
Base + 22	IO Point Diagnostic	—	0x0000 to	0 = OK, 1 = Error
	Bitmap		0xFFFF	Bit 00 = IO Point diagnostic summary
				Bit 01 = Configuration invalid to default value used
Base + 25	Digital Input On/Off	—	0 to 1	digital input Off/On status: 0 = Off, 1 = On
	Status
Base + 26	Count	—	0 to	Number of times input has transitioned from Off to On
			99,999,999
Base + 28	On Time	Seconds	0 to	Duration that digital input has been On
			99,999,999
Digital Output Template

These configuration registers require that you enter the setup mode to change the register’s contents. Issue command 9020 to enter setup

￿￿	mode and 9021 to exit setup mode. See “Using the Command Interface to Change Configuration Registers” on page 187 for instructions
	on how to use the setup-mode commands.
© 2001 Schneider Electric All Rights Reserved		169