Parts and Functions, Front | HP FS-8000C manual

1.2 Parts and Functions

1.2Parts and Functions

This section provides explanations and illustrations for you to determine the parts and their functions. Try to be familiar with the names and functions of these parts for correct use and optimal performance.

1.2.1Front

Figure 1-1

1Operator Panel

Used to specify printer functions and display the printer operating status.

2Paper-full Sensor

This sensor detects the tray full condition. When the Face-down tray is full, the printer stops operating and urges you to clear the Face-down tray.

3Front Cover

When open, this cover gives you access to the internal component for replacing toner containers. The cover must also be open to clear paper jam.

4Top Paper Cassette (FS-8000C/FS-8000CN)/Duplex Drawer (FS-8000CD)

The cassette holds up to 500 sheets of A5 to A3 sizes. For the FS-8000CD, the top drawer includes the duplexer for two-sided printing.

5Bottom Paper Cassette

The cassette holds up to 500 sheets of A5 to A3 sizes as a second paper source (for the FS-8000C and FS-8000CN).

1-5

Image 20

HP FS-8000C manual Parts and Functions, Front

Contents

FS-8000C FS-8000CD FS-8000CN Legal Restriction on Printing IBM Program License Agreement Iii FCC statement for users in the United States Important Notes for Interface connectors Cdrh regulations Vii Viii Kyosera ECO-PRODUCT Page Contents Printer Drivers and Utilities Troubleshooting RS-232C Cable Connection Serial InterfaceRS-232C Protocol Ecosys Color FS-8000CN Ecosys Color FS-8000CEcosys Color FS-8000CD Hardware FeaturesGeneral Software Networking KPDL3 Kyocera Printer Description LanguageEthernet network interface Snmp compliance Parts and Functions Front Power Switch MP Multi-Purpose TrayPaper Stopper Face-down Tray Internal Rear Serial Interface Connector Memory Card SlotNetwork Interface Card Slot OPT1 Hard Disk or Network Interface Card Slot OPT2/HDD Clearance Handling Paper Paper specifications GeneralAvailable paper types Values Recommended Paper Size Product WeightMinimum and Maximum Paper Sizes Selecting the Right Paper GuidelinesPaper conditions Paper composition Basis weights Paper propertiesSmoothness Thickness Caliper Moisture content Grain Other properties of paper Special Paper Selecting the Special Paper Transparency Adhesive-backed labels Envelopes Colored paperPre-printed paper Recycled paper Using the Operator Panel Understanding the Operator Panel Message DisplayStatus Information Message Meaning Indicators in Message Display Error codesInterface Indicator Interface OP1 Paper Size Indicator Size Paper Type Indicator Type READY, DATA, and Attention Indicators Indicator Description GO Key Cancel KeyKeys Enter Key Menu KeyArrow Keys Using the Menu Selection System Made using the menu selection systemMenu System Road Map Menu Key Kpdl Font Select Opt.StackerMode None Clolor Mode Color Life Counters Service Menu Map and Status Pages Printing a Menu MapPrint Menu Map Print Menu Map ? Menu MAP Print Status Page ? Printing a StatusPrint Status Status Understanding the Status Installed Options Software VersionHardware Information Memory Interface Information Error LogConsumable Status Mode Quick Copy Proof-and-Hold Private Print Stored Job MPSJob Retention Job Storage Virtual mailbox can be used in PCL 5c emulation only Using Quick CopyVirtual Mailbox MPS Quick Copy HaroldQuick Copy ?Harold Quick Copy ?Arlen Using Proof-and-Hold Report CopiesReport Delete Deleting a Quick Copy Job MPS Printing a Private Job Private/Stored HaroldPrivate/Stored ?Harold Private/Stored ?Arlen Arlen ?Agenda Agenda 0000Agenda Copies 001 Agenda Copies Storing a Print Job Releasing a Stored Job Agenda ?Copies Deleting a Stored Job List Code JOB ? Printing a List of Code JobsList Code JOB Print VMB Data Tray001Richard Retrieving Jobs from Virtual Mailbox VMBPrint VMB Data Tray001 Print VMB Data Tray001? List of VMBList of VMB ? Printing a List of VMB Changing e-MPS Configuration Print jobs than specified Maximum Space Assigned to Temporary Code Jobs MPS ConfigurationQuick Copy Temp. Code JOB Size 050MB Perm. Code JOB Size 050MB Maximum Space Assigned to Permanent Code Jobs Maximum Space Assigned to Virtual Mailboxes VMB VMB Size 050MBVMB Size 50MB When the desired size is displayed, press the Enter key Changing Parallel Interface Mode Changing the Interface ParametersInterface ? Serial Interface ? Parallel Changing Serial Interface Parameters Parallel I/F ? Auto Baud Rate Range Changing Network Interface Parameters Interface ? Option NetWare EtherTalk Off Opt. StatusPage On IP Address 000.000.000.000 Resolving IP AddressOff IP Address Subnet Mask Gateway 000.000.000.000 Printing a Network Interface Card Status Interface ParallelOpt. StatusPage Opt. StatusPage ? Off Opt. StatusPage ? On Network Status Emulation ?PCL 5c Making Default SettingsDefault Emulation Emulation KC-GL Pen Width and ColorCode Set Pen Adjust ? Pen Pen1 Width 02dotsPen1 Color ? Black KC-GL Page Set ? A2 Alt. Emulation ?PCL 5c Alternative Emulation for Kpdl EmulationEmulation PCL 5c Print Kpdl Errs ? On Printing Kpdl ErrorsPrint Kpdl Errs Off Default Font FontFont Select Internal I000 Selecting Regular or Dark Courier/Letter Gothic Courier RegularCourier ? Regular Changing the Default Font Size Size Points Pitch 10.00 cpi Character Pitch for Courier/Letter Gothic Printing Lists of Fonts List Internal FontsList Internal Fonts? Prescribe Pagination Number of CopiesSet Copies 001 Orientation ? Portrait Print OrientationOrientation Portrait Protect Mode ProtectProtect ? On Protect ? Auto LF Action ? LF only Linefeed LF ActionLF Action LF only CR Action ?CR only Carriage-Return CR ActionCR Action CR only Setting Print Quality Above diagram is an approximate presentation of KIR1 KIR Print Quality EcoPrint KIR ModeKIR Mode ? On EcoPrint Mode Off EcoPrint Mode ? Off Tone Mode Tone NormalPaper size Simplex Normal Fine Duplex Color Mono A4/Letter A3/B4 Gloss Mode Tone ? Normal Gloss Mode Low Gloss Mode ? Low Setting up the RAM Disk RAM Disk Mode OffRAM Disk Mode ? Off Operating the Storage Device Reading/Writing to an Option Storage Device RAM Disk Size MbyteMemory Card Reading Fonts Read Fonts Read Fonts ?Read Data DataS001 Reading Data Writing Data to a memory card or the hard disk Read Data ?DataS002Write Data Press Deleting Data Delete Data DataS001Delete Data ?data name Format Format ?Formatting a Storage Device Guide of the hard disk for details Format Information Printing a Partition List List of Partitions List of Partitions ? Operating the Storage Device MP Tray Mode MP Tray Mode FirstPaper Handling Paper Handling MP Tray Size Setting MP Tray Paper SizeMP Tray Mode ? First Setting the MP Tray Paper Type MP Tray Type ? Plain Setting the Cassette Paper TypeMP Tray Type Plain Cassette 1 Type Plain Cassette 1 Type ? Plain Feed Select ? Cassette Selecting the Paper Feed SourceFeed Select Cassette Using the printer driver Duplex Printing FS-8000CDBinding Modes Paper jam may occur Duplex mode None Duplex mode ?None Is set Override A4/LT ? Off Overriding Difference between A4 and LetterOverride A4/LT Off Type Adjust Custom Type Adjust ? CustomCreating Custom Paper Types Selecting the Custom Type Position Selecting the Paper Weight Paper Weight NormalPaper Weight ? Normal Fuser Mode Middle Fuser Mode ? MiddleDuplex path Enable Selecting the Fuser Mode Resetting the Custom Paper Type Duplex path ? EnableReset Type Adjust Reset Type Adjust ? Stack Select ? Face-down tray Selecting the Output StackStack Select Face-down tray Collator mode Selecting the Option Sorter ModeMode Description Sorter mode Opt.StackerMode ? Sorter Mode Description Mailbox modeOpt.StackerMode Sorter Changed Color Mode Color Mode ? ColorColor Control Selecting Monochrome or Color Printing RGB Simulation ? None Matching Colors to Monitor RGB SimulationRGB Simulation None Ink Simulation ?None Using Ink SimulationInk Simulation None Color Calibration Color CalibrationColor Calibration ? Please wait Calibrating Reading Life Counters Displaying the Total Printed PagesLife Counters Total Print 0123456 Displaying the Oil Unit Life Oil Kit 0123456 Resetting the Toner Counter New Toner C Installed ? Other Modes Selecting the Message LanguageOthers MSG Language English Automatic Form Feed Timeout Setting Form Feed Time Out 030sec Setting the Sleep Timer Sleep Timer 030 minSleep Mode Form Feed Time Time Out 03 0sec Sleep Mode ? On Sleep Mode ? OffSleep Timer 030min Sleep Timer Timeout Time Sleep Timer 03 0min Received Data DumpPrint HEX-DUMP Print HEX-DUMP? Printer Resetting Processing Waiting Resource Protection Self test Please wait Please wait Calibrating Ready Resouce Prot ? Off Alarm Buzzer SettingResouce Prot Off Buzzer ? On Auto Continue SettingBuzzer Auto Continue Mode ? On Setting the Auto Continue Recovery TimeAuto Continue Mode On Auto Continue Timer 000sec Printing the Service Status Service MenuService 116 Printer Drivers Utilities Are only for examples Macintosh Printer Drivers and UtilitiesOperating Software Name Description System Windows Windows 95/98/Me or Windows NT 4.0/2000 Installing the Printer DriverPrinter Driver Macintosh Configuring the Printer Properties Printer Properties Click the Device Settings tab Option Devices Selecting the Default Output Destination Defaults Windows NT 4.0 or Printing Preferences Windows Selecting the Default Paper 2000 Printing Using the Printer Driver Basic Printing Task Advanced Printing Tasks Selecting the Paper Source Selecting the Output Destination Color Mode, Color Correction, and Color Adjustment Handling TrueType FontsDownload TrueType fonts as Outline Correction Color ModeAdjustment Color Adjustment dialog box Printing in N-UpSaturation and Lightness RGB Level Printing Using the Printer Driver Configuring the Network Printer Installing a Printer Driver for Macintosh Troubleshooting Tips Symptom Check Items Corrective ActionGeneral Guidelines All-black printout Print Quality ProblemsPrinted Results Corrective Action Completely blank printout Faint or blurred printing Ity Tone Printing incomplete or out of position Printed Results Corrective Action Grey backgroundDirt on the top edge or back of the paper Printed Results Corrective Action Oily streaks at the top Approximately 15 cm below Message Corrective Action Error MessagesError Messages Cancel key Face-up tray. Open the face-up tray Operator Panel, .10.5 Selecting the Paper Feed Source on Topmost to 3 bottom as displayed in place of # Storage Error Codes Hard Disk ErrorsMemory Card Errors Code Meaning RAM Disk Errors Clearing Paper Jams Possible Paper Jam LocationsDuplex unit PF-30A General considerations for clearing jams Utilizing Online Help Messages Paper Jam Feeder # Cover Paper Jam Cassette # Paper Jam MP Tray Paper Jam Duplexer Drawer Paper Jam Paper Feed Unit Cover Colored. Remove the jammed paper Rear side while removing the paper Primary transfer unit Paper Jam Side Cover Paper Jam Option Stacker Maintenance Starter Toner Containers Toner Container ReplacementFrequency of toner container replacement Toner Kits TK-82C Cyan TK-82M Magenta TK-82Y Yellow TK-82K Black Power off Replacing the Toner ContainerDamaging media by the magnetism of toner Black K Yellow Y Magenta M Cyan C When it is properly seated Replacing the Waste Toner Bottle Place Replacing the Oil unit Fuser Unit Push Here areas Push the paper feed unit back in completely Local code or regulations for waste disposal Replacing the Maintenance Kit D Separation Charger Unit Transfer unit. Press the back side to lock the unit MaintenanceD MaintenanceD? Cleaning the Printer Cleaning the Paper Feed Unit Grasp handle on the paper feed unit and slowly pull it out Charger wires inside Close the front cover Cleaning the Main Charger Unit Grid cleaner out of the protective bag and remove the cap Grid cleaner cannot be reused. Close the front cover Appendix a Options Options Figure A-1 Expansion Memory Modules Figure A-2 Installing the Memory Modules Figure A-3 Memory socket until it clicks in place Testing the expanded memory Removing a Memory Module Reading Font from the Memory Card General Description of OptionsMemory Card 2 PF-30A Paper Feeder Figure A-9 3 PD-30 Duplex Unit Figure A-10 4 SO-30 Sorter 5 ST-30 Bulk Stacker 6 DF-31 Document Finisher 7 CA-31 Casters and CA-31B Caster Kit 8 HD-3 Hard Disk 9 BC-1 Barcode Reader 10 IB-20/IB-21E Network Interface Cards Figure A-17 Appendix B Computer Interface Parallel Interface Communication Modes Interface Signals Pin Signal Description Out Table B-1 Serial connector Pin Or out Signal DescriptionSerial Interface Interface voltage levels RS-232C Protocol Parameters of the RS-232C ProtocolH1 Baud rate H2 Number of data bits Prescribe Frpo D0 Command Preparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Changing Serial Interface Parameters on Using DOS for Serial Connection Figure B-2 Appendix C Technical Specifications Printer Specification Specification Inches deep Mode Paper Size Print Speeds Color Monochrome Printing Speeds Index KIR Prescribe Index-4 Kyocera Corporation