HP LCS60 Processor Board Firmware Update, set, env, set, env, env, Note:, ⎜ N, ⎜ B, ⎜ N, ⎜ A, ⎜ Y, ⎜ N, ⎜ N, ⎜ N, ⎜ N, 197-Bug, mmddyyhhmm

Processor Board Firmware Update

If the MVME197E processor board has been replaced, the set and env must be executed to reset the time and date and autoboot functions.

After replacing the board, attach a console to the console port on the rear of the LCS60 as described in Chapter 2. Then turn the LCS60 rear power switch on. Within a few seconds, boot messages will begin to appear on the console screen. At the 197-Bugprompt use the set command to enter the date (in the format mmddyyhhmm, that is, month, day, year, hour, minute), and use the env command to reset the autoboot. Refer to Screen 9-6.

Note: Responses to the prompts generated by the env command are listed in the table below.

_________________________________________________________
⎜ Bug or System environment [B/S]=S?	⎜	B	⎜
⎜	⎜		⎜
⎜ Field Service Menu Enable [Y/N]=Y?	⎜ N		⎜
⎜ Remote Start Method Switch [G/M/B/N]=B?	⎜ B		⎜
⎜	⎜		⎜
⎜ Probe System for Supported Disk/Tape Controllers [Y/N]=Y?	⎜	Y	⎜
⎜ Negate VMEbus SYSFAIL* Always [Y/N]=N?	⎜ N		⎜
⎜ Local SCSI Bus Reset on Debugger Startup [Y/N]=N?	⎜	Y	⎜
⎜	⎜		⎜
⎜ Local SCSI Bus Negotiations Type [A/S/N]=A?	⎜ A		⎜
⎜ Ignore CFGA Block on a Hard Disk Boot [Y/N]=Y?	⎜ Y		⎜
⎜	⎜		⎜
⎜ Auto Boot Enable [Y/N]= N?	⎜	Y	⎜
⎜ Auto Boot at power-up only [Y/N]= Y?	⎜ N		⎜
⎜ Auto Boot Controller LUN = 00?	⎜	0	⎜
⎜	⎜		⎜
⎜ Auto Boot Device LUN = 00?	⎜ 0		⎜
⎜ Auto Boot Abort Delay = 15?	⎜ 15		⎜
⎜	⎜	<CR>	⎜
⎜ Auto Boot Default String [NULL for an empty string]=?	⎜		⎜
⎜ ROM Boot Enable [Y/N]=N?	⎜ N		⎜
⎜ ROM Boot at power-up only [Y/N]=Y?	⎜	Y	⎜
⎜	⎜		⎜
⎜ ROM Boot Enable search of VMEbus [Y/N]=N?	⎜ N		⎜
⎜ ROM Boot Abort Delay =0?	⎜ 0		⎜
⎜	⎜		⎜
⎜ ROM Boot Direct Starting Address = FF800000?	⎜	FF800000	⎜
⎜ ROM Boot Direct Ending Address - FFBFFFFC?	⎜ FFBFFFFC		⎜
⎜	⎜		⎜
⎜ Network Auto Boot Enable [Y/N]= N?	⎜ N		⎜

Maintenance

Issue 3 9-19