Manuals / Brands / Computer Equipment / Personal Computer / Intel / Computer Equipment / Personal Computer

Intel Intel NetStructure Single Board Computer, MPCBL0010 13.0 Maintenance

1 198

Download 198 pages, 3.04 Mb

Intel NetStructure® MPCBL0010 Single Board Computer

October 2006 Technical Product Specification

Order Number: 304120 177

Maintenance—MPCBL0010 SBC

13.0 Maintenance

13.1 Supervision

Table151 lists the main components that perform hardware monitoring of voltages and

timers.

13.2 Diagnostics

13.2.1 In-Target Probe (ITP)

The ITP connector supports the use of a tool that helps you observe and control the

step-by-step execution of your program for debugging hardware and software.

Debugging includes finding a hardware or software error and identifying the location

and cause of the error so it can be corrected.

To maximize the development and delivery of mission-critical tools, we works with third

party vendors to develop and deliver specific tools. The following vendors provide in-

circuit emulation hardware and software:

• American Arium* currently develops in-circuit emulation and run control tools for

Intel processors.

http://www.arium.com/

• Agilent Technologies* currently develops logic analyzer and probing tools for Intel

processors.

http://we.home.agilent.com

• Tektronix* currently develops logic analyzer and probing tools for Intel processors.

http://www.tek.com/Measurement/logic_analyzers/index.html

Table 151. Hardware Monitoring Components

Component Function Monitors

Intelligent Platform Management

Controller (IPMC) WDT #1 Commands from the BIOS. If the timer expires (times out),

causes a hard reset, power down, or power cycle and IPMI

event.

6300ESB (Intel® 82801CA I/O

Controller Hub 3) WDT #3 The first attempt to fetch an instruction after a power

failure.

FWUM (R1C13) WDT #2

Strobed by IPMC firmware. If it expires, it isolates The

MPCBL0010 SBC from the backplane IPMB buses, and

resets the IPMC. Also performs fail safe field upgrade of the

IPMC.

Contents

Main Page Contents Page Page Page Page Figures Tables Page Page Revision History 1.0 Introduction 1.1 Document Organization 1.2 Glossary Page 2.0 Feature Overview 2.1 Application 2.2 Functional Description MPCBL0010 SBCFeature Overview Figure 1. MPCBL0010 Block Diagram 2.2.1 Low Voltage Intel Xeon Processor 6300ESB I/O Controller Hub (ICH) Intel 2.2.2 Chipset E7520 Memory Controller Hub (MCH) 2.2.3 Memory (J10, J12) 2.2.4 I/O 2.2.4.1 I/O Controller Hub 2.2.4.2 Real-Time Clock 2.2.4.3 Timers 2.2.4.4 Gigabit Ethernet 2.2.5 AdvancedMC (AMC) Connector (J18, J19) 2.2.6 Firmware Hubs 2.2.6.1 FWH0 (Main BIOS) 2.2.6.2 FWH1 (Backup/Recovery BIOS) 2.2.6.3 Flash ROM Backup Mechanism 2.2.7 Onboard Power Supplies 2.2.7.1 Power Feed Fuses 2.2.7.2 ORing Diodes and Circuit Breaker Protection 2.2.7.3 Isolated -48 V to +12 V, 12 V Suspend, 5 V, 3.3 V Suspend, 1.8 V, and 1.5 V Converters 2.2.7.4 Processor Voltage Regulator Module (VRM) 2.2.8 IPMC 2.2.9 Telecom Clock 2.2.10 AdvancedMC Direct Connect 2.2.11 AdvancedTCA Compliance 3.0 Operating the Unit 3.1 Jumpers Figure 4. Jumper/Connector Locations Table 2. Jumper Definitions 3.2 AdvancedMC Filler Panels 3.3 Installing Memory 3.4 Installing and Extracting the SBC 3.4.1 Chassis Installation 3.4.2 Chassis Extraction Page 3.5 AdvancedMC Module Installation and Extraction 3.6 BIOS Configuration 3.7 Remote Access Configuration 3.8 Software Updates 3.8.1 BIOS Updates FWH0 FWH1 FWH0 FWH1 Page 3.8.2.4 flashlnx Command Line Options 3.8.3 IPMC Firmware Updates 3.8.3.1 IPMC Firmware Upgrade Using the KCS Interface 3.9 Digital Ground to Chassis Ground Connectivity 4.0 Specifications 4.1 Mechanical Specifications 4.1.1 Board Outline 4.1.2 Backing Plate and Top Cover 4.2 Environmental Specifications 4.3 Reliability Specifications 4.3.1 Mean Time Between Failure (MTBF) Specifications 4.3.1.1 Environmental Assumptions 4.3.1.2 General Assumptions 4.3.1.3 General Notes 4.4 Weight 5.0 Connectors and LEDs Figure 10. Connector Locations Table 10. On-board and Backplane Connector Assignments Page 5.1 Backplane Connectors 5.1.1 Power Distribution Connector (P10) 5.1.2 AdvancedTCA Data Transport Connector (J23) Page 5.1.3 AdvancedTCA Data Transport Connector (J20) 5.1.4 Alignment Blocks 5.2 On-Board Connectors 5.2.1 POST Code Connector (J13) 5.2.2 Extended IPT700 Debug Port Connector (J25) 5.3 Front Panel Connectors 5.3.1 Ethernet 10/100 Debug Connector (J3) 5.3.2 USB Connector (J4) 5.3.3 Serial Port Connector (J5) Figure 15. USB Connector (J4) Table 18. USB Connector (J4) Pin Assignments Figure 16. Serial Port Connector (J5) 5.3.4 AdvancedMC* Connectors (J18, J19) Table 20. AdvancedMC* Connector Pin Assignments 5.4 LEDs Figure 19. Front Panel LEDs (Option 1) Figure 20. Front Panel B LEDs (Option 2) Table 21. Front Panel LED Descriptions (Sheet 1 of 2) 5.4.1 POST LED Codes Table 22. Ethernet 10/100 Debug Connector LED Operation Table 21. Front Panel LED Descriptions (Sheet 2 of 2) 5.5 Reset Button 6.0 BIOS Features 6.1 Introduction 6.2 BIOS Flash Memory Organization 6.3 Complementary Metal-Oxide Semiconductor (CMOS) 6.4 Redundant BIOS Functionality 6.5 Legacy USB Support 6.5.1 Language Support 6.6 Recovering BIOS Data 6.7 Boot Options 6.7.1 CD-ROM and Network Boot 6.8 Fast Booting Systems 6.8.1 Quick Boot 6.9 BIOS Security Features 6.10 Remote Access Configuration Table 24. Function Key Escape Code Equivalents (Sheet 2 of 2) 7.0 BIOS Setup 7.1 Introduction 7.2 Main Menu 7.3 Advanced Menu 7.3.1 CPU Configuration Sub-Menu 7.3.2 IDE Configuration Sub-Menu Page 7.3.2.1 Primary IDE Master/Slave Configuration Options Tabl e 31 shows the IDE Master/Slave configuration options. Table 30. IDE Configuration Sub-Menu (Continued) Table 31. IDE Master/Slave Sub-Menu 7.3.3 SuperIO Configuration Sub-Menu 7.3.4 ACPI Configuration Sub-Menu 7.3.4.1 Advanced ACPI Configuration Sub-Menu 7.3.4.2 Chipset ACPI Configuration Sub-Menu 7.3.5 System Management Sub-Menu 7.3.6 Event Log Configuration Sub-Menu Table 37. Event Log Configuration Sub-Menu 7.3.6.1 PCI Express Error Masking Configuration Sub-Menu 7.3.7 MPS Configuration Sub-Menu 7.3.8 AdvancedTCA* Channel Routing (PICMG*) Sub-Menu Tabl e 40 shows MPS Configuration options. 7.3.9 On-board Devices Configuration Sub-Menu To access this sub-menu, select Advanced on the menu bar, then On-board Devices Configuration. 7.3.10 PCI Express* Configuration Sub-Menu 7.3.11 Remote Access Configuration Sub-Menu 7.3.12 IPMI Configuration Sub-Menu Page 7.3.13 USB Configuration Sub-Menu 7.3.13.1 USB Mass Storage Device Configuration Tabl e 48 shows USB Mass Storage Device Configuration options. 7.4 PCIPnP Menu Table 47. USB Configuration Sub-Menu (Continued) Table 48. USB Mass Storage Device Configuration Main Advanced PCIPnP Boot Security Chipset Exit Table 49. PCIPnP Menu 7.5 Boot Menu 7.5.1 Boot Settings Configuration Sub-Menu 7.5.2 Boot Device Priority Sub-Menu 7.5.3 Hard Disk Drives Sub-menu 7.5.4 OS Load Timeout Timer Sub-Menu 7.6 Security Menu 7.7 Chipset Menu 7.7.1 Northbridge Configuration Sub-Menu 7.7.2 Spread Spectrum Clocking Mode Sub-Menu 7.8 Exit Menu Table 59. Exit Menu (Continued) 8.0 Error Messages 8.1 BIOS Error Messages 8.2 Port 80h POST Codes Table 61. Bootblock Initialization Code Checkpoints Table 62. POST Code Checkpoints Table 62. POST Code Checkpoints (Continued) Table 63. DIM Code Checkpoints Table 64. ACPI Runtime Checkpoints Table 62. POST Code Checkpoints (Continued) 9.0 Addressing 9.1 PCI Configuration Map Tabl e 65 lists the PCI devices and the bus on which they reside. Table 65. PCI Configuration Map Page 9.2 FPGA Registers Table 66. FPGA Register Legend POST codes are captured in this register as they are written. POST codes are captured in this register as they are written. Table 67. FPGA Register Overview Table 68. POST Codes 00:80h Table 69. Extended POST Codes 0081h Page Page TXREFx_SEL[2..0]=111 TXREFx_SEL[2..0]=101 Page Page 9.3 IPMC Addresses Table 83. IPMC Register Legend (Continued) Table 84. SBC Control 00h 9.3.0.1 PwrBtn usage Page Page Page Page Page Page Page Page Page 10.0 Hardware Management Overview 10.1 Intelligent Platform Management Controller (IPMC) Page 10.2 Sensor Data Record (SDR) Table 109. Hardware Sensors (Sheet 2 of 4) Table 109. Hardware Sensors (Sheet 3 of 4) Table 110. OEM Sensor Types Table 109. Hardware Sensors (Sheet 4 of 4) 10.3 System Event Log (SEL) Table 111. OEM Event/Reading Type Table 112. SEL Events Supported (Sheet 1 of 5) Table 112. SEL Events Supported (Sheet 2 of 5) Table 112. SEL Events Supported (Sheet 3 of 5) Table 112. SEL Events Supp orted (Sheet 4 of 5) Table 112. SEL Events Supported (Sheet 5 of 5) 10.4 IPMB Link Sensor 10.5 Field Replaceable Unit (FRU) Information 10.6 Customizable FRU Area 10.6.1 LinuxCustFru Utility Usage fileName -p -v 10.6.2 FRU Customer Area Page Page 10.7 E-Keying 10.8 OEM IPMI Commands 10.8.1 Reset BIOS Flash Type 10.8.2 Board Device Channel Port Selection Identifiers Page 10.8.2.2 GetBoardDeviceChannelPortSelection This command returns the current device AdvancedTCA channel routing selection. This command returns the possible selections for the device received in parameters. 10.8.2.3 GetBoardDevicePossibleSelection Table 117. GetBoardDeviceChannelPortSelection 10.8.3 Set Control State This command sets the state of a control pin and overrides the control pins auto state. 10.8.4 Get Control State This command gets the state of a control pin. 10.8.5 Controls Identifier Table 10.9 Hot Swap Process ICH3 10.9.1 Hot Swap LED 10.10 AdvancedMC Module Activation 10.10.1 Pre-Defined Resources for AdvancedMC Modules 10.11 Temperature and Voltage Sensors Table 123. Sensors and Thresholds (Version SDR 040) 10.11.1 Processor Events 10.11.2 DIMM Memory Events 10.11.3 System Firmware Progress (POST Error) 10.11.4 Critical Interrupts 10.11.5 System ACPI Power State 10.12 Reset 10.12.1 Warm Reset 10.12.2 Hard Reset 10.13 Field Replaceable Unit (FRU) Information 10.14 IPMC Firmware Code Page Page 11.0 Serial Over LAN (SOL) 11.1 References 11.2 SOL Architecture 11.2.1 SOL Implementation Page 11.2.2 Architectural Components 11.2.2.1 IPMC 11.2.2.2 Ethernet Controller 11.3 Theory of Operation 11.3.1 Front Panel Serial Port or Rear Transition Module 11.4 Serial Over LAN Client 11.5 Reference Configuration Script 11.6 Supported Usage Model 11.6.1 Configuring the Blade for SOL 11.7 Reference Script (reference_cfg) 11.7.1 SOL Configuration Reference Script (reference_cfg) 11.7.2 Default Behavior 11.7.3 SOL User Information 11.7.4 LAN Parameters 11.7.5 SOL Parameters 11.7.6 Channel Parameters 11.7.7 Command Line Options 11.8 Setting up a Serial Over LAN Session 11.8.1 Target Blade Setup 11.8.1.1 BIOS Configuration 11.8.1.2 Operating System Configuration Page 11.8.1.3 sbcutils RPM Installation 11.8.1.4 Execute the reference_cfg Script Page 11.8.2 Client Blade Setup 11.8.2.1 Configure the Ethernet Port 11.8.2.2 Installing ipmitool 11.8.2.3 Start an SOL Session 11.8.2.4 Checking SOL Configuration 11.8.2.5 Ending an SOL Session 11.9 Operating Systems for SOL Client (ipmitool) 12.0 Telecom Clock 12.1 Functional Description 12.2 Interface Description 12.2.1 AdvancedTCA Backplane Interface 12.2.2 AdvancedMC Interface 12.2.3 Reset/Interrupt Interface 12.2.4 LPC Interface 12.3.3 Recovered Clock Selection 12.3.4 Configuration 12.3.4.1 Operational Configuration 12.3.5 Alarm Handling 12.4 Telecom Clock API 12.4.1 TRANSMIT CLOCK 12.4.2 Enable/Disable Transmission Clock 12.4.3 Recovered Clock 12.4.4 Automatic Switchover 12.4.5 Automatic Switchover Mode 12.4.6 Select Reference Clock 12.4.7 Reference Frequency for PLL 12.4.8 Primary/Secondary Redundant Clock 12.4.9 Corner Frequency 12.4.10 PLL Operating Mode 12.4.11 Reference Clock Alignment 12.4.12 Hardware Reset 12.4.13 Read Alarm States 12.4.14 Read New Events 12.4.15 Read the Current Reference Clock 12.4.16 sysfs Interface 12.5 Telecom Clock Registers Page Page Page Page Page Table 150. FPGA/PLD Serial Link Bit Definition 13.0 Maintenance 13.1 Supervision 13.2 Diagnostics 13.2.1 In-Target Probe (ITP) 14.0 Thermals 15.0 Component Technology 16.0 Warranty Information 16.1 Intel NetStructure Compute Boards and Platform Products Limited Warranty 16.2 Returning a Defective Product (RMA) 16.3 For the Americas 16.3.1 For Europe, Middle East, and Africa (EMEA) 16.3.2 For Asia and Pacific (APAC) 16.3.3 Limitation of Liability and Remedies Page 17.0 Customer Support 17.1 Customer Support 17.2 Technical Support and Return for Service Assistance 17.3 Sales Assistance 17.4 Product Code Summary 18.0 Certifications 19.0 Agency InformationClass B 19.1 North America (FCC Class B) 19.3 Japan VCCI Class B 19.2 Canada Industry Canada (ICES-003 Class B) (English and French-translated) Page 20.0 Safety Warnings 20.1 Mesures de Scurit 20.2 Sicherheitshinweise 20.3 Norme di Sicurezza 20.4 Instrucciones de Seguridad Page Appendix A Reference Documents Page Appendix B List of Supported Commands (IPMI v1.5 and PICMG 3.0) Table 153. IPMI 1.5 Supported Commands (Sheet 1 of 2) Table 153. IPMI 1.5 Supported Commands (Sheet 2 of 2) Table 154. PICMG 3.0 IPMI Supported Commands