Display of detailed information on a past trip | Toshiba VF-FS1

E6581381

8.1.2Display of detailed information on a past trip

Details on a past trip (of trips 1 to 4) can be displayed, as shown in the table below, by pressing the ENT key when the trip record is selected in the status monitor mode.

Unlike the "Display of detailed trip information at the occurrence of a trip" in 8.2.2, details on a past trip can be displayed, even after the inverter is turned off or reset.

Note 10

Note 1

Note 2

Note 3

8

Note 4

Note 5

Note 8

Item displayed	Key	LED display		Description
Item displayed	operated	LED display		Description
	operated
Past trip 1		QE⇔	Past trip 1 (displayed alternately)

Continuous trips	ENT	P	The number of time the same trip occurred in succession is
Continuous trips	ENT	P	displayed. (Unit: times)

Operation		Z	The operation frequency when the trip occurred is
frequency		Z	displayed.
frequency			displayed.

Direction of		HTH	The direction of rotation when the trip occurred is displayed.
rotation		HTH	(HTH: Forward run, HTT: Reverse run)
rotation			(HTH: Forward run, HTT: Reverse run)
Operation			The operation command value when the trip occurred is
frequency		H	displayed.
command
Load current		E	The inverter output current when the trip occurred is
Load current		E	displayed. (%/A)

Input voltage		[	The inverter input voltage (DC) when the trip occurred is
Input voltage		[	displayed. (%/V).

Output voltage		R	The inverter output voltage when the trip occurred is
Output voltage		R	displayed. (%/V)

			The ON/OFF statuses of the control input terminals (F, R,
			RES and VIA) are displayed in bits.

			ON:	__KK
			OFF: _	__KK
Input terminal		__KK	OFF: _

			VIA			F
			VIA			F
						R
						RES

			The ON/OFF statuses of the control output terminals (RY
			and FL) are displayed in bits.
			ON:
Output terminal		_K	ON:		_K
Output terminal		_K	OFF: _		_K
			OFF: _

				FL	RY-RC
Cumulative			The cumulative operation time when the trip occurred is
Cumulative		V	displayed.
operation time		V	displayed.
operation time			(0.01=1 hour, 1.00=100 hours)
			(0.01=1 hour, 1.00=100 hours)
Past trip 1	MODE	QE⇔	Press this key to return to past trip 1.

H-4

Image 190

Toshiba VF-FS1 instruction manual Display of detailed information on a past trip, HtH

Contents

Industrial Inverter Page Safety precautions Safety precautionsMeanings of symbols Explanation of markings General Operation Transportation & installation Wiring Operations When retry function is selected inverter Maintenance and inspection Disposal Attach warning labels Features II. Introduction  Contents  E6581381 Iii Read first Check product purchase Contents of the product Names and functions Outside view Bottom Power circuit and control circuit terminal boards Power circuit terminal board VFFS1-2004 ∼ 2037PM VFFS1-4004 ∼ 4055PL E6581381 E6581381 Grounding capacitor disconnecting switch and taps Control circuit terminal board AWG How to open the front terminal board cover-18.5kW or less How to open the front terminal board cover-22kW or More Motors Occurrence of instability Braking a motor when cutting off power supplyLow loads and low inertia loads Load that produces regenerative torque Measures to protect motors against surge voltages InvertersBraking motor Protecting inverters from overcurrent Operating at other than rated voltage Power factor correction capacitorIf power supply distortion is not negligible MCCB1 Remedies What to do about the leak currentEffects of leak current across ground Elcb Affects of leakage current across lines Installation Installation environment 5cm How to install Standard installation Side-by-side installation Operating motor Calorific Values w Installing more than one unit in a cabinet Page Connection Standard connections Control and main power supplyWiring Preventing radio noise Standard connection diagram Standard connection diagram Power circuit terminals Description of terminals Control circuit terminals Power circuitControl circuit terminals VIA VIB FLB FLAFLC PLC Logic switching Operations Eoqf Simplified Operation of the VF-FS1Hoqf Start and stop using the operation panel keys EOQF= How to start and stopExample of a Eoqf setting procedure Coast stop Example of operating a run from the panel How to set the frequencyExample of a Hoqf setting procedure HOQF Setting the frequency using the operation panel HOQF= or Frequency setting How to operate the VF-FS1 Mccb Page Mode for monitoring all inverter status Setting monitor mode Mode for setting inverter parametersBasic VF-FS1 operations Flow of status monitor mode How to set parameters Basic parameters Extended parameters User parameters How to set the basic parameters Changes the parameter setting Saves the changed value How to set extended parameters How to search and reprogram parameters Search and resetting of changed parameters I4WExample of parameter setting ITW CEE Setting a parameter, using the wizard function CWHHTH How to use the wizard function How Parameters of Quick setting wizard CWJ How to use the history functionJgcf Parameters that cannot be changed while running CW How to save/load the user setting parameters Returning all parameters to standard default settingKpkv Page Basic parameters Setting acceleration/deceleration timeAutomatic acceleration/deceleration Methods of setting automatic acceleration/deceleration Manually setting acceleration/deceleration timeCWK Function Adjustment range Default setting EOF Specifying an operation mode, using parametersUP/DOWN UP/DOWN HOF RES PLC VIA VIB OFF Selection of operation mode Setting mode Switching of commands and references Command mode selection Frequency setting mode selection Preset-speed operation HOUN= Meter setting and adjustmentHoun Meter selection HO Meter adjustment Houn Adjustment scale with parameter HO Meter adjustment ResolutionVF-FS1 Adjusting the meter in inverter stop state HOUN= VR Default setting Standard default settingProgrammed value E6581381 Forward/reverse run selection Operation panel operation HT Forward/reverse run selection Operation panel operation HJ Maximum frequency Maximum frequencyUpper limit and lower limit frequencies WN Upper limit frequency NN Lower limit frequency Base frequency XN Base frequency XNX Base frequency voltage Selecting control mode RV V/F control mode selection Constant torque characteristics Setting for fans and pumps Increasing starting torque Motor constant must be set Energy-saving Precautions on vector control+ Motor constant must be set Operating a permanent magnet motor E6581381 Valid, Invalid Manual torque boost increasing torque boost at low speeds Setting the electronic thermalXD Torque boost Motor electronic thermal protection levelQNO Setting value Overload protection Overload stall Inverter over load characteristics Motor 150%-overload time limit H UT UT Preset-speed operation frequencies Preset-speed operation speeds in 7 stepsThermal memory selection H UT UTUT UT Below is an example of 7-step speed operation Extended parameters Low-speed signal Low-speed signal output frequency Input/output parameters Output of designated frequency reach signal Speed reach detection band Output of set frequency speed reach signal Designated frequency Changing the functions of VIA terminal Input signal selection VIA terminal function selection Keeping an input terminal function always active on Terminal function selectionModifying input terminal functions Setting of contact input terminal function Connection method 1 A-contact input Connection with transistor output Sink Negative logic / Source Positive logic input Modifying output terminal functionsExamples of application Assigning one function to an output terminal Assigning two functions to an output terminalRY RC RY-RC Input terminal function Holding the output of signals in on statusHdry Comparing the frequency command values FLA-FLB-FLC Switching motor characteristics via terminal input Basic parameters Frequency priority selection Setting of switching terminalsAD2 VF2 MOT2 OCS2 OFF External switching Input terminal function 38 Fchg enabled Automatic switching by frequency command Setting frequency command characteristics 10Vdc voltage input adjustment VIA, VIB VIA, VIB terminals Setting of frequency with the input from an external contact Sample sequence diagram 1 Adjustment with continuous signals Adjustment with pulse signals Parameter-setting example Minimum unit of frequency adjustment About the setting of the initial up/down frequencyFrequency adjustment range About the change of the initial up/down frequency Fine adjustment of frequency setting signal Operation frequency 2 Run/stop control with frequency setting signals Starting frequency setting Starting frequency DC braking DC braking OFF Jump frequency jumping resonant frequencies Bumpless operation Bumpless operation selection PWM carrier frequency 0.75kW 15kW E6581381 Auto-restart Restart of coasting motor Trip-less intensification Auto-restart control selection Restarting motor during coasting Motor speed search function Motor speed search at starting Instantaneous power failure coast stop selection Instantaneous power failure coast stop selection Retry function Retry selection Selecting the number of times E6581381 Avoiding overvoltage tripping Output voltage adjustment/Supply voltage correction Canceling the operation command Reverse-run prohibition Droop control  Droop gain  Droop insensitive torque band E6581381 Conducting PID control External connection Adjusting the PID control gain level Setting PID controlTypes of PID control interfaces P-gain adjustment parameter I-gain adjustment parameter Adjusting analog command voltages D-gain adjustment parameterSetting the time elapsed before PID control starts Setting motor constants Setting motor constants Set the auto-tuning parameter H to Auto-tuning enabled E6581381 Setting motor constants 2 Details E6581381 Acceleration/deceleration time Selecting an acceleration/deceleration pattern Switching acceleration/deceleration time 1 E6581381 Setting motor electronic thermal protection Protection functions Setting current stall Stall prevention level  Inverter trip retention Inverter trip retention selection External trip stop via terminals Emergency stop Emergency stop Emergency DC braking time Emergency stopping from the operation panel Output phase failure detection Output phase failure detection mode selection Control mode for small current Input phase failure detection Input phase failure detection mode selection Detection of output short-circuit Detection of output short-circuit during start-up Over-torque trip OFF On OFF Over-voltage stall protection level Cumulative operation time alarm setting Cumulative operation time alarm setting Over-voltage stall protection level Undervoltage trip/alarm selection Undervoltage trip Parts replacement alarms Trip at VIA low level input mode Trip at VIA low level input mode Motor PTC thermal protection Evasion from Overvoltage and Imput phase failure Forced fire-speed control function NNWN Example of setting Adjustment parametersCalibration of analog outputs Resetting method Prohibition of key operations and parameter settingsOperation panel parameter Changing the unit to a Current / voltage unit An example of setting when HJ is 80 and H is Changing the steps in which the value displayed changes When H is not 0.00, and H is not 0 disabled Free pressing a panel key once Free panel display Changing the display format while power is on Changing the item displayed by default Standard monitor display selection Display of the head of the parameters Integral output powerSelection of operation panel stop pattern Selection of operation panel stop pattern Title Communication function Common serial Setting of common functionError by disconnection Communication rate Communication function parameters Common serial options E6581381 Transmission specifications Using the RS485Setting the communication functions Example of connection for RS485-communication Wiring Parameters for options Permanent magnetic motorsPage HOQF Setting the operation frequencyApplied operation HOQF Hoqf P24Hoqf PLC VIA SS3 VIB RES Setting the operation mode RES SC/LC RES SC/LC PLC VIA VIB Status monitor under normal conditions Status monitor modeMonitoring the operation status LED KK VIA RES Pgtt ⇔ Display of detailed information on a past trip Trip code display Display of trip informationDisplay of trip information Display of trip information at the occurrence of a trip Example of call-up of trip information Input terminal KK FE06 OFF Cause of the trip is displayed E6581381 Page Measures to satisfy the standards How to cope with the CE directiveAbout the EMC directive Measures to satisfy the EMC directive Three-phase 400V class Example of wiring About the low-voltage directive Measures to satisfy the low-voltage directive Compliance with InstallationCompliance with UL Standard and CSA Standard Compliance with Connection Motor thermal protection AIC, Fuse and Wire sizesAIC a Selection of wiring materials and devices Peripheral devices Selection of wiring devices Input current a Installation of a magnetic contactor Magnetic contactor in the primary circuit Installation of an overload relay Magnetic contactor in the secondary circuit Optional external devices Page 11.1 User parameters Table of parameters and data11.2 Basic parameters Houn UT Extended parameters Input/output parameters Frequency parameters Operation mode parameters NNWN Torque boost parameters Acceleration/deceleration time parameters Protection parameters Output parameters Operation panel parameters Communication parameters Default settings by inverter rating PM motor parameters Table of input terminal functions AD2 OHN Table of output terminal functions LLN UCN Pidfn Order of precedence of combined functions Models and their standard specifications SpecificationsStandard specifications Common specification Display Outside dimensions and mass Outside dimensions and mass Outline drawing Fig.A Fig.E Before making a service call Trip information and remedies Trip causes/warnings and remedies QR GTT QHH Restoring the inverter from a trip If the motor does not run while no trip message is displayed How to determine the causes of other problems How to cope with parameter setting-related problemsPage Inspection and maintenance Regular inspection Check points Periodical inspectionCheck items Replacement of expendable parts Standard replacement cycles of principal parts Making a call for servicing Keeping the inverter in storagePage Warranty Disposal of the inverter Page Toshiba