Toshiba VF-FS1 instruction manual Display

			E6581381
<Continued>
	Item		Specification
function	Protective function	Stall prevention, current limitation, over-current, output short circuit, over-voltage, over-voltage limitation,
		torque, undercurrent, overheating, cumulative operation time, life alarm, emergency stop, various pre-
		undervoltage, ground fault, power supply phase failure, output phase failure, overload protection by
		electronic thermal function, armature over-current at start-up, load side over-current at start-up, over-
Protective		alarms
	Reset function	Function of resetting by closing contact 1a or by turning off power or the operation panel. This function is
	Electronic thermal	Switching between standard motor and constant-torque VF motor, switching between motors 1 and 2,
	characteristic	setting of overload trip time, adjustment of stall prevention levels 1 and 2, selection of overload stall
		also used to save and clear trip records.
	Alarms	Stall prevention, overvoltage, overload, under-voltage, setting error, retry in process, upper/lower limits
	Causes of failures	Over-current, overvoltage, overheating, short-circuit in load, ground fault, overload on inverter, over-
		current through arm at start-up, over-current through load at start-up, CPU fault, EEPROM fault, RAM
		fault, ROM fault, communication error. (Selectable: Emergency stop, under-voltage, low voltage, over-
		torque, motor overload, output open-phase)
	Monitoring function	Operation frequency, operation frequency command, forward/reverse run, output current, voltage in DC
		section, output voltage, torque, torque current, load factor of inverter, input power, output power,
		information on input terminals, information on output terminals, version of CPU1, version of CPU2,
function		version of memory, PID feedback amount, frequency command (after PID), integral input power, integral
	Past trip monitoring	output power, rated current, output speed, communication counter, normal state communication counter,
		Stores data on the past four trips: number of trips that occurred in succession, operation frequency,
		causes of past trips 1 through 4, parts replacement alarm, cumulative operation time
Display	function	direction of rotation, load current, input voltage, output voltage, information on input terminals, information
	Output for frequency	Analog output: (1mAdc full-scale DC ammeter or 7.5Vdc full-scale DC ammeter / Rectifier-type AC
		on output terminals, and cumulative operation time when each trip occurred.
	meter	voltmeter, 225% current Max. 1mAdc, 7.5Vdc full-scale), 4 to 20mA/0 to 20mA output
	4-digit 7-segments LED	Frequency:	inverter output frequency.
		Alarm:	stall alarm “C”, overvoltage alarm “P”, overload alarm “L”, overheat alarm “H”.
		Status:	inverter status (frequency, cause of activation of protective function, input/output voltage,
			output current, etc.) and parameter settings.
		Free-unit display: arbitrary unit (e.g. rotating speed) corresponding to output frequency.
	Indicator	Lamps indicating the inverter status by lighting, such as RUN lamp, MON lamp, PRG lamp, % lamp, Hz
		lamp, LOC/REM key lamp, UP/DOWN key lamp and RUN key lamp. The charge lamp indicates that the
		main circuit capacitors are electrically charged.
Environments	Use environments	Indoor, altitude: 1000m (Max.), not exposed to direct sunlight, corrosive gas, explosive gas or vibration
	Relative humidity	20 to 93% (free from condensation and vapor).
			(less than 5.9m/s2) (10 to 55Hz)
	Ambient temperature	-10 to +60°C Note1) Note2)
	Storage temperature	-20 to +65°C

Note 1: Above 40°C: Remove the seal from the top of the inverter and use the inverter with the rated output current reduced.

Note 2: If inverters are installed side by side (with no sufficient space left between them): Remove the seal from the top of each inverter.

When installing the inverter where the ambient temperature will rise above 40°C, remove the seal from the top of the 12 inverter and use the inverter with the rated output current reduced.

L-3