
E6581381
■Table of input terminal functions 2
|
| Function | Code | Function | Action |
|
| No. | |||
|
|
|
|
| |
|
| 43 | CLR | Frequency UP/DOWN cancellation signal input | OFF→ON: Resetting of UP/DOWN frequency by |
|
|
|
| from external contacts | means of external contacts |
|
| 44 | CLR+RES | Combination of frequency UP/DOWN cancellation | ON: Simultaneous input from CLR and RES |
|
|
|
| and reset by means of external contacts |
|
|
| 45 | EXTN | Inversion of trip stop command from external | OFF: G Trip stop |
|
|
|
| device |
|
|
| 46 | OH | Thermal trip stop signal input from external device | ON: QJ Trip stop |
|
| 47 | OHN | Inversion of thermal trip stop command from | OFF: QJ Trip stop |
|
|
|
| external device |
|
|
| 48 | SC/LC | Forced switching from remote to local control | Enabled when remote control is exercised |
|
|
|
|
| ON: Local control (setting of EOQF, HOQF and |
|
|
|
|
| H) |
|
|
|
|
| OFF: Remote control |
|
| 49 | HD | Operation holding (stop of | ON: F (forward run)/R: (reverse run) held, |
|
|
|
|
| operation |
|
|
|
|
| OFF: Slowdown stop |
|
| 51 | CKWH | Display cancellation of the cumulative power | ON: Monitor display cancellation of the cumulative |
|
|
|
| amount (kWh) | power amount (kWh) |
|
| 52 | FORCE | Forced operation (factory configuration required) | ON: Forced operation mode in which operation is |
|
|
|
|
| not stopped in the event of the occurrence of |
|
|
|
|
| a soft fault (preset speed operation frequency |
|
|
|
|
| 7) To use this function, the inverter needs to |
|
|
|
|
| be so configured at the factory. |
|
|
|
|
| OFF: Normal operation |
|
| 53 | FIRE | ON: | |
|
|
|
|
| speed setting frequncy) |
|
|
|
|
| OFF: Normal operation |
|
| 54 | STN | Coast stop (gate off) | ON: Coast stop (gate off) |
|
| 55 | RESN | Inversion of RES | ON: Acceptance of reset command |
|
|
|
|
| OFF→ ON: Trip reset |
|
| 56 | F+ST | Combination of forward run and standby | ON: Simultaneous input from F and ST |
|
| 57 | R+ST | Combination of reverse run and standby | ON: Simultaneous input from R and ST |
|
| 61 | OCS2 | Forced switching of stall prevention level 2 | ON: Enabled at the value of H |
|
|
|
|
| OFF: Enabled at the value of H |
|
| 62 | HDRY | Holding of | ON: Once turned on, |
|
|
|
|
| OFF: The status of |
|
|
|
|
| according to conditions. |
|
| 64 | PRUN | Cancellation (clearing) of operation command from | 0: Operation command canceled (cleared) |
|
|
|
| panel | 1: Operation command retained |
|
| 65 | ICLR | PID control integral value clear | ON: PID control integral value always zero |
|
|
|
|
| OFF: PID control permitted |
|
| 66 | ST+F+SS1 | Combination of standby, forward run and preset- | ON: Simultaneous input from ST, F and SS1 |
11 |
|
|
| speed command 1 |
|
| 67 | ST+R+SS1 | Combination of standby, reverse run and preset- | ON: Simultaneous input from ST, R and SS1 | |
|
|
| speed command 1 |
| |
|
| 68 | ST+F+SS2 | Combination of standby, forward run and preset- | ON: Simultaneous input from ST, F and SS2 |
|
|
|
| speed command 2 |
|
|
| 69 | ST+R+SS2 | Combination of standby, reverse run and preset- | ON: Simultaneous input from ST, R and SS2 |
|
|
|
| speed command 2 |
|
|
| 70 | ST+F+SS3 | Combination of standby, forward run and preset- | ON: Simultaneous input from ST, F and SS3 |
|
|
|
| speed command 3 |
|
|
| 71 | ST+R+SS3 | Combination of standby, reverse run and preset- | ON: Simultaneous input from ST, R and SS3 |
|
|
|
| speed command 3 |
|
Note: When function 1, 10, 11, 16, 38,