Manuals / Toshiba / Computer Equipment / Power Supply

Toshiba VF-FS1 instruction manual E6581381

Models: VF-FS1

1 252

Download 252 pages 5.48 Kb

Page 88

E6581381

5)Use a motor that has 2-8 P.

6)Always operate the motor in single operation (one inverter to one motor). Sensorless vector control cannot be used when one inverter is operated with more than one motor.

7)The maximum length of wires between the inverter and motor is 30 meters. If the wires are longer than 30 meters, set standard auto-tuning with the wires connected to improve low-speed torque during sensorless vector control.

However the effects of voltage drop cause motor-generated torque in the vicinity of rated frequency to be somewhat lower.

8)Connecting a reactor or surge voltage suppression filter between the inverter and the motor may reduce motor-generated torque. Setting auto-tuning may also cause a trip (GVP) rendering sensorless vector control unusable.

8)The following table shows the relationship between the V/F control mode selection (RV) and the motor constant parameter.

		Under normal conditions, be sure to set or adjust the parameters marked with .
		When making detailed settings, adjust the parameters marked with as well, if necessary.
		Do not adjust the parameters marked with , because they are invalid.
	5
	5	(For instructions about how to adjust the parameter H and later, see section 6.17.)

E-22

Image 88

Toshiba VF-FS1 instruction manual E6581381

Contents

Industrial Inverter Page Safety precautions Meanings of symbolsSafety precautions Explanation of markingsGeneral Operation Transportation & installation WiringOperations When retry function is selected inverter Maintenance and inspectionDisposal Attach warning labelsFeatures II. Introduction Contents  E6581381 Iii Read first Check product purchaseContents of the product Names and functions Outside viewBottom Power circuit and control circuit terminal boards Power circuit terminal boardVFFS1-2004 ∼ 2037PM VFFS1-4004 ∼ 4055PL E6581381 E6581381 Grounding capacitor disconnecting switch and taps Control circuit terminal board AWGHow to open the front terminal board cover-18.5kW or less How to open the front terminal board cover-22kW or More Motors Braking a motor when cutting off power supply Low loads and low inertia loadsOccurrence of instability Load that produces regenerative torqueInverters Braking motorMeasures to protect motors against surge voltages Protecting inverters from overcurrentPower factor correction capacitor If power supply distortion is not negligibleOperating at other than rated voltage MCCB1What to do about the leak current Effects of leak current across groundRemedies ElcbAffects of leakage current across lines Installation Installation environment5cm How to install Standard installation Side-by-side installationOperating motor Calorific Values w Installing more than one unit in a cabinet Page Connection Control and main power supply WiringStandard connections Preventing radio noiseStandard connection diagram Standard connection diagram Power circuit terminals Description of terminalsControl circuit terminals Power circuitControl circuit terminals VIA VIBFLB FLAFLC PLC Logic switching Operations Eoqf Simplified Operation of the VF-FS1Hoqf How to start and stop Example of a Eoqf setting procedureStart and stop using the operation panel keys EOQF= Coast stopHow to set the frequency Example of a Hoqf setting procedureExample of operating a run from the panel HOQFSetting the frequency using the operation panel HOQF= or Frequency settingHow to operate the VF-FS1 Mccb Page Mode for monitoring all inverter status Setting monitor mode Mode for setting inverter parametersBasic VF-FS1 operations Flow of status monitor mode How to set parameters Basic parameters Extended parameters User parametersHow to set the basic parameters Changes the parameter setting Saves the changed valueHow to set extended parameters Search and resetting of changed parameters I4W Example of parameter settingHow to search and reprogram parameters ITWCEE Setting a parameter, using the wizard function CWHHTH How to use the wizard function How Parameters of Quick setting wizardCWJ How to use the history functionJgcf Parameters that cannot be changed while running CWHow to save/load the user setting parameters Returning all parameters to standard default settingKpkv Page Basic parameters Setting acceleration/deceleration timeAutomatic acceleration/deceleration Methods of setting automatic acceleration/deceleration Manually setting acceleration/deceleration timeCWK Function Adjustment range Default setting Specifying an operation mode, using parameters UP/DOWNEOF UP/DOWN HOFRES PLC VIA VIB OFF Selection of operation mode Setting mode Switching of commands and referencesCommand mode selection Frequency setting mode selection Preset-speed operationMeter setting and adjustment Houn Meter selection HO Meter adjustmentHOUN= HounAdjustment scale with parameter HO Meter adjustment ResolutionVF-FS1 Adjusting the meter in inverter stop state HOUN=VR Default setting Standard default settingProgrammed value E6581381 Forward/reverse run selection Operation panel operation HT Forward/reverse run selection Operation panel operationMaximum frequency Upper limit and lower limit frequenciesHJ Maximum frequency WN Upper limit frequency NN Lower limit frequencyBase frequency XN Base frequency XNX Base frequency voltageSelecting control mode RV V/F control mode selectionConstant torque characteristics Setting for fans and pumpsIncreasing starting torque Motor constant must be setPrecautions on vector control + Motor constant must be setEnergy-saving Operating a permanent magnet motorE6581381 Valid, Invalid Manual torque boost increasing torque boost at low speeds Setting the electronic thermalXD Torque boost Motor electronic thermal protection levelQNO Setting value Overload protection Overload stall Inverter over load characteristics Motor 150%-overload time limit HUT UT Preset-speed operation frequencies Preset-speed operation speeds in 7 stepsThermal memory selection H UT UTUT UTBelow is an example of 7-step speed operation Low-speed signal Low-speed signal output frequencyExtended parameters Input/output parametersOutput of designated frequency reach signal Speed reach detection bandOutput of set frequency speed reach signal Designated frequencyChanging the functions of VIA terminal Input signal selection VIA terminal function selection Keeping an input terminal function always active on Terminal function selectionModifying input terminal functions Setting of contact input terminal function Connection method 1 A-contact input Connection with transistor outputSink Negative logic / Source Positive logic input Modifying output terminal functionsExamples of application Assigning one function to an output terminal Assigning two functions to an output terminalRY RC RY-RC Input terminal function Holding the output of signals in on statusHdry Comparing the frequency command values FLA-FLB-FLCSwitching motor characteristics via terminal input Basic parametersFrequency priority selection Setting of switching terminalsAD2 VF2 MOT2 OCS2 OFF External switching Input terminal function 38 Fchg enabled Automatic switching by frequency commandSetting frequency command characteristics 10Vdc voltage input adjustment VIA, VIB VIA, VIB terminalsSetting of frequency with the input from an external contact Sample sequence diagram 1 Adjustment with continuous signals Adjustment with pulse signals Parameter-setting exampleAbout the setting of the initial up/down frequency Frequency adjustment rangeMinimum unit of frequency adjustment About the change of the initial up/down frequencyFine adjustment of frequency setting signal 2 Run/stop control with frequency setting signals Starting frequency settingOperation frequency Starting frequencyDC braking DC brakingOFF Jump frequency jumping resonant frequencies Bumpless operation Bumpless operation selectionPWM carrier frequency 0.75kW 15kW E6581381 Auto-restart Restart of coasting motor Trip-less intensification Auto-restart control selection Restarting motor during coasting Motor speed search function Motor speed search at startingInstantaneous power failure coast stop selection Instantaneous power failure coast stop selectionRetry function Retry selection Selecting the number of timesE6581381 Avoiding overvoltage tripping Output voltage adjustment/Supply voltage correction Canceling the operation command Reverse-run prohibitionDroop control  Droop gain  Droop insensitive torque bandE6581381 Conducting PID control External connectionAdjusting the PID control gain level Setting PID controlTypes of PID control interfaces P-gain adjustment parameter I-gain adjustment parameterAdjusting analog command voltages D-gain adjustment parameterSetting the time elapsed before PID control starts Setting motor constants Setting motor constantsSet the auto-tuning parameter H to Auto-tuning enabled E6581381 Setting motor constants 2 Details E6581381 Acceleration/deceleration time Selecting an acceleration/deceleration patternSwitching acceleration/deceleration time 1 E6581381 Setting motor electronic thermal protection Protection functionsSetting current stall Stall prevention level  Inverter trip retention Inverter trip retention selection Emergency stop Emergency stop Emergency DC braking timeExternal trip stop via terminals Emergency stopping from the operation panelOutput phase failure detection Output phase failure detection mode selectionControl mode for small current Input phase failure detection Input phase failure detection mode selection Detection of output short-circuit Detection of output short-circuit during start-upOver-torque trip OFF On OFF Cumulative operation time alarm setting Cumulative operation time alarm settingOver-voltage stall protection level Over-voltage stall protection level Undervoltage trip/alarm selection Undervoltage tripParts replacement alarms Trip at VIA low level input mode Trip at VIA low level input mode Motor PTC thermal protection Evasion from Overvoltage and Imput phase failure Forced fire-speed control function NNWNExample of setting Adjustment parametersCalibration of analog outputs Resetting method Prohibition of key operations and parameter settingsOperation panel parameter Changing the unit to a Current / voltage unit An example of setting when HJ is 80 and H is Changing the steps in which the value displayed changes When H is not 0.00, and H is not 0 disabled Free pressing a panel key once Free panel display Changing the display format while power is on Changing the item displayed by default Standard monitor display selection Integral output power Selection of operation panel stop patternDisplay of the head of the parameters Selection of operation panel stop patternTitle Setting of common function Error by disconnectionCommunication function Common serial Communication rate Communication function parameters Common serial options E6581381 Using the RS485 Setting the communication functionsTransmission specifications Example of connection for RS485-communicationWiring Parameters for options Permanent magnetic motorsPage Setting the operation frequency Applied operationHOQF HOQFHoqf P24Hoqf PLC VIA SS3 VIB RES Setting the operation mode RES SC/LCRES SC/LC PLC VIA VIB Status monitor mode Monitoring the operation statusStatus monitor under normal conditions LEDKK VIA RESPgtt ⇔ Display of detailed information on a past trip Trip code display Display of trip informationDisplay of trip information Display of trip information at the occurrence of a trip Example of call-up of trip informationInput terminal KK FE06 OFF Cause of the trip is displayed E6581381 Page Measures to satisfy the standards How to cope with the CE directiveAbout the EMC directive Measures to satisfy the EMC directive Three-phase 400V class Example of wiring About the low-voltage directiveCompliance with Installation Compliance with UL Standard and CSA StandardMeasures to satisfy the low-voltage directive Compliance with ConnectionMotor thermal protection AIC, Fuse and Wire sizesAIC a Selection of wiring materials and devices Peripheral devicesSelection of wiring devices Input current aInstallation of a magnetic contactor Magnetic contactor in the primary circuitInstallation of an overload relay Magnetic contactor in the secondary circuitOptional external devices Page 11.1 User parameters Table of parameters and data11.2 Basic parameters Houn UT Extended parameters Input/output parametersFrequency parameters Operation mode parameters NNWN Torque boost parameters Acceleration/deceleration time parameters Protection parameters Output parameters Operation panel parametersCommunication parameters Default settings by inverter rating PM motor parametersTable of input terminal functions AD2OHN Table of output terminal functions LLNUCN Pidfn Order of precedence of combined functions Models and their standard specifications SpecificationsStandard specifications Common specification Display Outside dimensions and mass Outside dimensions and massOutline drawing Fig.AFig.E Before making a service call Trip information and remedies Trip causes/warnings and remediesQR GTT QHH Restoring the inverter from a trip If the motor does not run while no trip message is displayed How to determine the causes of other problems How to cope with parameter setting-related problemsPage Inspection and maintenance Regular inspectionCheck points Periodical inspectionCheck items Replacement of expendable parts Standard replacement cycles of principal parts Making a call for servicing Keeping the inverter in storagePage Warranty Disposal of the inverter Page Toshiba