Cisco Systems OL-6244-01 - page 518

2-466

Catalyst 6500 Series Switch Command Reference—Release8.4

OL-6244-01

Chapter2 Catalyst 6500 Series Switch and ROM Monitor Commands

set port auxiliaryvlan

The presence of an IP phone is determined through CDP packet exchange between the switch a nd the

phone. This detection method is used for both inline-powered I P ph one s and wal l-powered IP phon es.

If the auxiliary VLAN ID equals the port-VLAN ID or when the auxiliary VLAN ID is configured as none,

dot1p, or untagged, this featu re ca nno t b e a ppl ie d to the por t. If any command entry results in the auxiliary

VLAN ID equaling the port-VLAN ID, the feature is disabled and the following warning message is

displayed:

cdpverify feature on port mod/port is disabled.

Examples This example shows how to set the auxiliary VLAN port to untagged:

Console> (enable) set port auxiliaryvlan 5/7 untagged

Port 5/7 allows the connected device send and receive untagged packets and

without 802.1p priority.

Console> (enable)

This example shows how to set the auxiliary VLAN port to dot1p:

Console> (enable) set port auxiliaryvlan 5/9 dot1p

Port 5/9 allows the connected device send and receive packets with 802.1p priority.

Console> (enable)

This example shows how to set the auxiliary VLAN port to none:

Console> (enable) set port auxiliaryvlan 5/12 none

Port 5/12 will not allow sending CDP packets with AuxiliaryVLAN information.

Console> (enable)

This example shows how to set the auxiliary VLAN port to a specific module, port, and VLAN:

Console> (enable) set port auxiliaryvlan 2/1-3 222

Auxiliaryvlan 222 configuration successful.

AuxiliaryVlan AuxVlanStatus Mod/Ports

------------- ------------- -------------------------

222 active 1/2,2/1-3

Console> (enable)

Related Commands show port auxiliaryvlan

Contents

Main Page CONTENTS Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Preface Audience Organization Related Documentation Conventions Obtaining Documentation Cisco.com Ordering Documentation Documentation Feedback Obtaining Technical Assistance Cisco Technical Support Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page CHAPTER Command-Line Interfaces Switch CLI Accessing the Switch CLI Accessing the Switch CLI via the Console Port (EIA/TIA-232) Accessing the Switch CLI via Telnet Operating the Switch CLI Accessing the Command Modes Using Command-Line Processing Using the Command-Line Editing Features Moving Around on the Command Line Completing a Partial Command Name Pasting in Buffer Entries Editing Command Lines That Wrap Deleting Entries Scrolling Down a Line or a Screen Scrolling to Specified Text Redisplaying the Current Command Line Transposing Mistyped Characters Controlling Capitalization Designating a Keystroke as a Command Entry Using Command Aliases Using History Substitution 1-9 Accessing Command Help Top-Level Commands and Command Categories Command Categories Context-Sensitive Help Designating Modules, Ports, and VLANs Designating MAC Addresses, IP and IPX Addresses, and IP Aliases Using Command Completion Features Using Command Self-Repeat Using Keyword Lookup Using Partial Keyword Lookup Using Command Completion Using the CLI String Search Regular Expressions Single-Character Patterns Page Multiple-Character Patterns Multipliers Alternation Anchoring ROM Monitor CLI Accessing the ROM Monitor CLI Operating the ROM Monitor CLI Page CHAPTER Catalyst 6500 Series Switch and ROM Monitor Commands alias Page boot cd clear acllog clear acl mac-packet-classify clear alias clear arp Page clear autoshut clear banner motd clear boot auto-config clear boot device clear boot system clear cam clear cam monitor clear cam notification clear channel statistics clear config Page clear config checkpoint clear config pvlan clear cops Page clear counters Page clear crypto key rsa clear dhcp-snooping bindings Page clear dhcp-snooping statistics clear dot1x config clear dot1x vlan-group Page clear ftp clear gmrp statistics clear gvrp statistics clear igmp statistics clear ip alias clear ip dns domain clear ip dns server clear ip permit Page clear ip route clear kerberos clients mandatory clear kerberos credentials forward clear kerberos creds clear kerberos realm clear kerberos server clear key config-key clear l2protocol-tunnel cos clear l2protocol-tunnel statistics clear lacp-channel statistics clear lda Page clear localuser clear log clear log command clear logging buffer clear logging callhome Page clear logging callhome from clear logging callhome reply-to clear logging callhome severity clear logging callhome smtp-server clear logging level Page clear logging server clear mls cef clear mls cef rpf statistics clear mls entry Page clear mls entry cef clear mls exclude protocol clear mls multicast statistics clear mls nde clear mls nde flow clear mls statistics Page clear mls statistics entry Page clear module password clear msfcautostate clear multicast router clear ntp server clear ntp timezone clear pbf clear pbf arp-inspection clear pbf client clear pbf gw clear pbf-map Page clear pbf vlan clear port broadcast clear port cops clear port host clear port qos autoqos clear port qos cos clear port security Page clear port vlan-mapping clear pvlan mapping clear qos acl Page Page clear qos autoqos Page Page clear qos config clear qos cos-cos-map clear qos cos-dscp-map clear qos dscp-cos-map clear qos dscp-mutation-map clear qos dscp-mutation-table-map clear qos ipprec-dscp-map clear qos mac-cos clear qos map Page clear qos policed-dscp-map clear qos policer Page clear qos statistics clear radius clear rcp clear rgmp statistics clear security acl Page clear security acl capture-ports clear security acl counters clear security acl cram clear security acl log flow clear security acl map Page clear security acl statistics clear snmp access clear snmp access-list clear snmp community clear snmp community-ext clear snmp group clear snmp ifalias clear snmp inform clear snmp notify clear snmp targetaddr clear snmp targetparams clear snmp trap clear snmp user clear snmp view clear spantree detected-protocols clear spantree mst Page clear spantree portcost clear spantree portinstancecost Page clear spantree portinstancepri clear spantree portpri clear spantree portvlancost Page clear spantree portvlanpri clear spantree root Page clear spantree statistics Page clear spantree uplinkfast clear ssh mode clear system info-log command clear system profile clear tacacs key clear tacacs server clear timezone clear top clear trunk clear vlan Page clear vlan counters clear vlan mapping clear vmps rcp clear vmps server clear vmps statistics clear vtp pruneeligible clear vtp statistics commit Page commit lda configure 2-185 Related Commands co py show config confreg 2-187 Related Commands show boot context 2-189 copy Page Page 2-193 These examples show how to use the copy command to download a configuration from a TFTP server: 2-194 This example shows how to copy the running configuration to an rcp server for stora ge: This example shows how to upload an image from a remote host into Flash using an rcp server: 2-195 This example shows how to copy the ACL configuration to a bootflash file manually: This example shows a complete SCP download procedure of a crypto image to the switch: 2-196 This example shows how to upload the crypto image to an SCP server: Page delete dev dirROM monitor dirswitch Page disable disconnect download Page 2-207 This example shows how to download a ROM image to module 9: 2-208 This example shows how to upgrade the EPLD image in force mode on the module in slot 5: enable format Page frame fsck Page historyROM monitor historyswitch l2trace Page Page meminfo ping Page Page pwd quit reconfirm vmps reload repeat 2-229 resetROM monitor resetswitch Page Page Page 2F2 restore counters Page rollback session set set accounting commands set accounting connect set accounting exec Page set accounting suppress set accounting system Page set accounting update set acllog ratelimit set acl mac-packet-classify set alias set arp Page set authentication enable Page set authentication login Page set authorization commands Page set authorization enable Page set authorization exec Page set autoshut Page set banner lcd set banner motd set banner telnet set boot auto-config set boot config-register Page Page set boot config-register auto-config Page Page set boot device Page set boot sync now set boot sync timer set boot system flash set cam Page set cam monitor Page set cam notification Page Page set cdp Page set channelprotocol Page set channel vlancost Page set config acl nvram set config checkpoint Page set config mode Page Page set config rollback set cops Page set crypto key rsa set default portstatus set dhcp-snooping Page set dot1q-all-tagged set dot1x Page Page Page Page set enablepass set errdisable-timeout Page set errordetection Page Page Page set fan-tray-version set feature agg-link-partner set feature mdg set firewall set ftp Page set garp timer set gmrp set gmrp fwdall set gmrp registration set gmrp timer Page set gvrp set gvrp applicant set gvrp dynamic-vlan-creation set gvrp registration Page set gvrp timer Page set igmp set igmp fastblock set igmp fastleave set igmp flooding set igmp leave-query-type set igmp mode set igmp querier Page set igmp v3-processing set image-verification set inlinepower Page set interface Page Page set ip alias set ip dns set ip dns domain set ip dns server set ip fragmentation set ip http port set ip http server set ip permit Page set ip redirect set ip route 2-364 Related Commands clear ip route show ip route set ip unreachable set kerberos clients mandatory set kerberos credentials forward set kerberos local-realm set kerberos realm set kerberos server set kerberos srvtab entry Page set kerberos srvtab remote set key config-key set l2protocol-tunnel cos set l2protocol-tunnel trunk set lacp-channel system-priority set lcperroraction set lda Page Page set length set localuser Page set logging buffer set logging callhome Page set logging callhome destination Page set logging callhome from set logging callhome reply-to set logging callhome severity Page set logging callhome smtp-server set logging console set logging history set logging level Page Page set logging server Page set logging session set logging telnet set logging timestamp set logout set macro ciscosmartports set mls agingtime Page set mls bridged-flow-statistics set mls cef load-balance set mls cef maximum-routes Page set mls cef per-prefix-statistics set mls exclude protocol set mls flow Page set mls nde Page Page Page Page set mls netflow-entry-create set mls netflow-per-interface set mls rate set mls statistics protocol set mls verify Page set module Page set module autoshut Page set module name set module power Page set module shutdown set msfcautostate Page set msmautostate set multicast ratelimit set multicast router set ntp broadcastclient set ntp broadcastdelay set ntp client set ntp server set ntp summertime Page set ntp timezone set password set pbf Page set pbf arp-inspection set pbf client Page set pbf gw Page set pbf-map Page Page set pbf vlan set poll set port arp-inspection Page set port auto-mdix Page set port auxiliaryvlan Page set port broadcast Page set port channel Page Page set port cops set port debounce Page set port dhcp-snooping Page set port disable set port dot1q-all-tagged Page set port dot1q-ethertype Page set port dot1qtunnel Page set port dot1x Page Page Page Page set port duplex set port enable set port errdisable-timeout set port errordetection set port flowcontrol Page set port gmrp set port gvrp Page set port host set port inlinepower Page set port jumbo set port l2protocol-tunnel Page Page set port lacp-channel Page set port macro Page 2-509 This example shows how to execute the Cisco Softphone configuration macro: Related Commands se t cd p set macro ciscosmartports set port qos autoqos set qos autoqos set port membership Page set port name set port negotiation set port protocol Page set port qos Page set port qos autoqos Page set port qos cos set port qos policy-source Page set port qos trust Page set port qos trust-device set port qos trust-ext set port rsvp dsbm-election set port security Page Page Page set port security-acl Page set port speed set port sync-restart-delay set port trap set port unicast-flood Page set port vlan-mapping Page set port voice interface dhcp Page set port vtp set power redundancy set prompt set protocolfilter set pvlan Page set pvlan mapping Page set qos set qos acl default-action Page set qos acl ip Page Page Page Page set qos acl ipx Page Page set qos acl mac Page Page set qos acl map Page set qos autoqos set qos bridged-microflow-policing set qos cos-cos-map set qos cos-dscp-map set qos drop-threshold Page set qos dscp-cos-map set qos dscp-mutation-map set qos dscp-mutation-table-map set qos dscp-rewrite set qos ipprec-dscp-map Page set qos mac-cos set qos map Page Page set qos policed-dscp-map set qos policer Page set qos policy-source Page set qos rsvp Page set qos rxq-ratio Page set qos statistics export set qos statistics export aggregate set qos statistics export destination Page set qos statistics export interval set qos statistics export port set qos txq-ratio Page set qos wred Page set qos wrr Page set radius attribute set radius deadtime set radius key set radius retransmit set radius server set radius timeout set rate-limit Page set rcp username set rgmp set rspan Page Page set security acl adjacency set security acl arp-inspection Page set security acl capture-ports set security acl cram Page set security acl feature ratelimit set security acl ip Page Page Page Page Page set security acl ipx Page Page set security acl log Page set security acl mac Page Page set security acl map Page Page set security acl statistics set snmp set snmp access Page set snmp access-list Page set snmp buffer set snmp chassis-alias set snmp community Page set snmp community-ext Page set snmp extendedrmon netflow set snmp group set snmp ifalias set snmp inform Page set snmp notify set snmp rmon set snmp rmonmemory set snmp targetaddr Page set snmp targetparams Page set snmp trap Page Page set snmp user Page set snmp view Page set span Page Page set spantree backbonefast set spantree bpdu-filter set spantree bpdu-guard set spantree bpdu-skewing set spantree channelcost Page set spantree channelvlancost set spantree defaultcostmode Page set spantree disable Page set spantree enable Page set spantree fwddelay Page set spantree global-default Page set spantree guard Page set spantree hello Page set spantree link-type set spantree macreduction set spantree maxage Page set spantree mode Page set spantree mst Page set spantree mst config Page set spantree mst link-type set spantree mst maxhops set spantree mst vlan set spantree portcost Page set spantree portfast set spantree portfast bpdu-filter set spantree portfast bpdu-guard set spantree portinstancecost Page set spantree portinstancepri Page set spantree portpri set spantree portvlancost Page set spantree portvlanpri set spantree priority Page set spantree root Page 2-726 Related Commands show spantree set spantree uplinkfast Page set ssh mode Page set summertime Page set system baud set system contact set system core-dump set system core-file set system countrycode set system crashinfo Page set system crossbar-fallback set system highavailability set system highavailability versioning Page set system info-log Page set system location set system modem set system name set system profile Page set system supervisor-update Page set system switchmode allow Page set system syslog-dump set system syslog-file set tacacs attempts set tacacs directedrequest set tacacs key set tacacs server set tacacs timeout set test diagfail-action set test diaglevel set time set timezone set traffic monitor set trunk Page Page set udld Page set udld aggressive-mode set udld interval set vlan Page Page Page Page set vlan mapping Page set vlan verify-port-provisioning set vmps config-file Page set vmps downloadmethod set vmps downloadserver set vmps server Page set vmps state set vtp Page Page Page set vtp pruneeligible show accounting 2-795 This example shows the configuration details of a switch with TACACS+ accounting enabled: Page show acllog show acl mac-packet-classify show aclmerge algo show alias show arp show authentication show authorization show autoshut show banner show boot show boot device show cam 2-809 This example shows how to display dynamic CAM entries for VLAN 1: This example shows routers listed as the CAM entries: Related Commands clear cam set cam show cam agingtime show config show cam agingtime show cam count show cam monitor show cam msfc show cam notification 2-815 This example shows how to display CAM notification information for ports 1-6 on modu le 2: This example shows how to display CAM notification intervals: This example shows how to display CAM notification history information: This example shows how to display CAM notification history size information: Page show cdp 2-818 This example shows how to display CDP information about neighboring systems: This example shows how to display duplex information about neighboring systems: This example shows how to display VLAN information about neighboring systems: 2-819 This example shows how to display capability information about neighboring system s: Related Commands se t cd p This example shows how to display CDP information for all ports: show channel 2-821 This example shows how to display channel information for all channels: This example shows how to display port information for a specific channel: This example shows how to display port information for all channels: 2-822 This example shows how to display PAgP information for all channels: This example shows how to display PAgP information for a specific channel: This example shows how to display statistics for a specific channel: 2-823 This example shows how to display statistics for all channels: 2-824 Related Commands show channel group show port channel show channel group 2-826 This example shows how to display group information: 2-827 Page show channel hash Page show channel mac show channelprotocol Page show channel traffic show config 2-836 2-837 2-838 This example shows how to display default and nondefault configuration information: 2-839 This example shows how to display nondefault system configuration information: This example shows how to display all system default and nondefault configuration inf orm ati on : This example shows how to display module nondefault configuration information: Page show config checkpoints show config differences Page show config mode show config qos acl show cops 2-847 This example shows how to display COPS RSVP status and configuration information: This example shows how to display the ports assigned to each role: This example shows how to display only IP addresses, not IP aliases: Page show counters 2-850 This example shows how to display the counters for the supervisor engine: Page Page Page Page show crypto key show default show dhcp-snooping bindings Page show dhcp-snooping config show dhcp-snooping statistics show dot1q-all-tagged show dot1x 2-863 This example shows how to display information about all 802.1X user groups: This example shows how to display information about authenticated user groups: 2-864 This example shows how to display information about a specific group: This example shows how to display information about all authenticated users: 2-865 This example shows how to display information about a specific authenticated user: This example shows how to display information about authenticated users in a VLAN: This example shows how to display information about a specific VLAN group: This example shows how to display information about all VLAN groups: show dvlan statistics show environment 2-868 Examples This example shows how to display environmental status information: 2-869 This example shows how to display temperature information: This example shows how to display the inline power for all modules: 2-870 This example shows how to display the inline power status for a specific module: This example shows how to display cooling information: Page Page show errdisable-timeout Page show errordetection show fabric channel Page 2-878 This example shows how to display switch mode and fabric channel status: This example shows how to display the counters for all fabric-enabled modules: Page Page show fabric errors Page show fabric status show file show firewall show flash 2-887 2-888 Related Commands download resetswitch show ftp show garp timer Page show gmrp configuration show gmrp statistics show gmrp timer show gvrp configuration Page show gvrp statistics Page show ifindex show igmp flooding show igmp gda_status show igmp leave-query-type show igmp mode show igmp querier information show igmp statistics Page show imagemib show image-verification show inlinepower Page show interface Page show inventory Page show ip alias show ip dns Page show ip http Page show ip permit Page 2s2 show ip route Page show kerberos Page show l2protocol-tunnel statistics Page show lacp-channel Page 2-930 This example shows how to display all ports that are assigned to an administrative key: Page show lcperroraction show lda Page 2-935 This example shows how to display uncommitted ASLB information: This example shows how to display ASLB information for the source IP address in shor t fo rm at: This example shows how to display the number of active ASLB MLS entries: Page show localuser show log Page Page show log command show logging Page show logging buffer show logging callhome Page show logging callhome destination Page show logging callhome from show logging callhome reply-to show logging callhome severity show logging callhome smtp-server show mac Page Page show microcode show mls Page show mls acl-route show mls cef exact-route show mls cef interface Page show mls cef mac show mls cef maximum-routes show mls cef rpf Page show mls cef summary Page show mls entry Page Page 2-972 For destination-only flow: For destination-source flow: For destination-source: Destination-only flow: 2-973 2-974 Related Commands clear mls statistics entry show mls entry cef 2-976 Examples This example shows how to display information for all CEF entries: These examples show how to display information for a specific entry type: Page Page show mls entry netflow-route Page show mls exclude protocol show mls multicast Page 2-984 Page show mls nde show mls netflow-route show mls pbr-route show mls statistics Page Page Page Page show mls verify show module 2-996 This example shows the display for an 8-port T1/E1 ISDN PRI servi ces- co nfigured m odule : Page show moduleinit Page show msfcautostate show msmautostate show multicast group Page show multicast group count show multicast protocols status show multicast ratelimit-info show multicast router Page show multicast v3-group show netstat Page Page Page Page Page Page show ntp Page show pbf 2-1020 This example shows how to display adjacency information for adjacency a_1: This example shows how to display statistics for PFC2: This example shows how to display statistics for adjacency a_1: This example shows how to display the adjacency map for PFC2: Page show pbf arp-inspection show pbf client show pbf gw show pbf-map Page show poll show port 2-1029 Examples This example shows how to display the status and counters for a specific module and port: This example shows port information on a 48-port 10/100BASE-TX module with i nli ne p ower: 2-1030 2-1031 2-1032 Page Page Page show port arp-inspection show port auto-mdix show port auxiliaryvlan Page show port broadcast Page show port capabilities 2-1043 This example shows the port capabilities on an 8-port T1/E1 ISDN PRI services configured-module: 2-1044 This example shows the port capabilities on an Intrusion Detection System Module: Page Page show port cdp Page show port channel 2-1050 Examples This example shows how to display Ethernet channeling informat ion fo r mod ul e 1: This example shows how to display port statistics: This example shows how to display port information: 2-1051 Page Page Page show port cops Page show port counters Page show port debounce show port dhcp-snooping Page show port dot1q-all-tagged show port dot1q-ethertype show port dot1qtunnel show port dot1x Page show port errdisable-timeout Page show port errordetection show port flowcontrol Page show port inlinepower Page Page show port jumbo show port l2protocol-tunnel show port lacp-channel 2-1078 This example shows how to display LACP channel information for all ports on module 4: This example shows how to display LACP channel information for port 7 on module 4: This example shows how to display detailed LACP channel information for port 7 on module 4: This example shows how to display LACP channel statistics for all ports on module 4: Page show port mac Page show port mac-address 2-1083 show port negotiation show port prbs show port protocol show port qos 2-1088 Page show port rsvp show port security 2-1092 This example shows how to display system-wide configuration information: Page show port security-acl Page show port spantree show port status show port sync-restart-delay show port tdr Page show port trap show port trunk Page show port unicast-flood show port vlan-mapping show port voice 2-1107 2-1108 Related Commands set port voice interface dhcp show port voice fdl show port voice interface show port voice active 2-1110 This example shows how to display regular calls: This example shows how to display calls for a specified port: 2-1111 Page show port voice fdl Page show port voice interface show port vtp 2-1117 Related Commands se t port vtp set vtp show vtp show proc 2-1119 This example shows how to display process information: Page Page show protocolfilter show pvlan Page show pvlan capability Page show pvlan mapping Page show qos acl editbuffer show qos acl info Page show qos acl map Page show qos acl resource-usage show qos bridged-microflow-policing show qos info 2-1137 This example shows how to display QoS-related NVRAM receive-threshold information: 2-1138 This example shows how to display all QoS-related NVRAM threshold information: This example shows how to display the current QoS runtime information: 2-1139 This example shows another display of the current QoS runtime information: 2-1140 This example shows how to display the current QoS configuration information: Page show qos mac-cos Page show qos maps 2-1145 Examples This example shows how to display the cos-dscp-map map: This example shows how to display the ipprec-dscp-map map: This example shows how to display the dscp-cos-map map: This example shows how to display the policed-dscp-map map: 2-1146 This example shows how to display normal-rate maps: This example shows how to display the configuration for DSCP mutation map 1: 2-1147 Page show qos policer Page show qos policy-source show qos rsvp show qos statistics Page show qos statistics export info show qos status show radius show rate-limit 2-1159 This example shows how to display the Layer 2 rate-limiter operational status i nfor ma tion: Related Commands set rate-limit show rcp show reset show rgmp group show rgmp statistics show rspan 2-1165 Related Commands se t rspan show running-config 2-1167 2-1168 This example shows how to display the nondefault system configuration for module 3: Related Commands clear config show startup-config write show security acl 2-1170 Examples This example shows how to display the name and type of the VACLs currently configured: This example shows how to display VACLs in the edit buffer: 2-1171 This example shows how to display the contents of the VACL edit buffer: This example shows how to display statistics for the specified ACL: Page show security acl arp-inspection show security acl capture-ports show security acl cram show security acl feature ratelimit show security acl log Page Page show security acl map Page show security acl resource-usage show security acl tcam interface show snmp Page show snmp access Page show snmp access-list show snmp buffer show snmp community 2-1191 Related Commands clear snmp community set snmp community show snmp context show snmp counters Page Page Page show snmp engineid show snmp group Page show snmp ifalias show snmp inform show snmp notify Page show snmp rmonmemory show snmp targetaddr Page show snmp targetparams Page show snmp user Page show snmp view Page show span Page show spantree 2-1216 Page Page show spantree backbonefast show spantree blockedports show spantree bpdu-filter show spantree bpdu-guard show spantree bpdu-skewing Page show spantree conflicts Page show spantree defaultcostmode show spantree guard Page show spantree mapping 2-1231 This example shows how to display mappings configured on the local switch: Related Commands se t v lan show spantree mistp-instance Page show spantree mst Page show spantree mst config Page show spantree portfast show spantree portinstancecost show spantree portvlancost show spantree statistics 2-1242 2-1243 This example shows how to display instance-specific information: 2-1244 This example shows how to display MST instance-specific information: Page Page Page Page show spantree summary 2-1250 This example shows how to display non-VLAN-specific information only: This example shows how to display a summary of spanning tree instance inf orm ation : 2-1251 This example shows how to display a summary of spanning tree MST instanc e info rm atio n: Related Commands show spantree This example shows how to display a summary of spanning tree noninstance-specific MST informat ion: show spantree uplinkfast Page show ssh show startup-config 2-1256 Page show summertime show system 2-1260 Page Page show system health 2-1264 Related Commands show counters show proc show system sanity show system highavailability show system info-log show system profile show system sanity 2-1269 Related Commands show system show system supervisor-update show system switchmode show tacacs Page show tech-support Page show test 2-1277 This example shows the error display for module 3: This example shows the display when errors are reported by the LCP for module 3: 2-1278 This example shows the display if you do not specify a module: This example shows how to display diagnostic level status: Page Page show time show timezone show top Page show top report Page show traffic show trunk 2-1289 Examples This example shows how to display trunking information for the switc h: This example shows how to display detailed information about the specified trunk port: Page show udld Page show users show version 2-1295 This example shows how to display version information for a specific module: Page show vlan 2-1298 2-1299 This example shows how to display information for a specific VLAN and type: This example shows how to display information for nontrunk ports only on a specific VL AN : This example shows how to display extended-range VLANs: Page Page show vlan counters Page show vlan verify-port-provisioning show vmps Page show vmps mac show vmps statistics show vmps vlan show vtp Page show vtp domain Page show vtp statistics Page slip squeeze stack switch switch console switch fabric sync sysret tclquit tclsh telnet test cable-diagnostics Page test snmp trap traceroute Page Page unalias undelete unset=varname varname= verify wait whichboot write 2-1341 Examples This example shows how to upload the system5.cfg file to the mercury host : This example shows how to upload the system5.cfg file to the mercury host: This example shows how to display the configuration file on the terminal (partial display): Page write tech-support Page Page Page APPENDIX A Acronyms Page Page Page Page Page Page Page APPENDIX B Acknowledgments for Open-Source Software Page INDEX Symbols Numerics A Page B C Page Page D Page E F G H I J K L M Page Page N O P Page Q Page R S Page Page Page T Page U V Page W