Opening cross sections | Siemens 400 V / 210...590 A specs

01.2004	Installation

Opening cross sections

Partitions should be executed up to the cabinet frame and should be designed in such a way that the discharged air flow is taken around the cabinet beams and not pressed into them.

Partitions are necessary with all types of protection higher than IP20.

The necessary opening cross sections are 0.26 m2.

The indicated opening cross-section is made up of several holes. In order to keep the pressure loss here to a minimum, the cross-sectional surface has to be at least 280 mm2 per hole (e.g. 7 mm x 40 mm).

The opening and hole cross-sections ensure functioning even with high types of protection.

These are implemented by using wire-lattices (wire fabric DIN 4189- St-vzk-1x0.28) in front of the openings or the filters indicated in the following. If finer filters are used, the filter surface and thus the opening cross-section (upwards) have to be adapted accordingly.

If filters are used, the intervals for their replacement must be observed!

Siemens AG 6SE7087-6CX86-2BA1	5-5
SIMOVERT MASTERDRIVES AFE Operating Instructions

Image 23

Siemens 400 V / 210...590 A operating instructions Opening cross sections

Contents

Edition AB SimovertPage Contents 12-1 10-111-1 15-1 13-114-1 17-2 16-117-1 17.1 Definitions and Warnings Definitions and Warnings 01.2004 Standing Standing / Sitting Sitting General InstallationMaintenance and servicing Keep these safety instructions in a safe place Operating range DescriptionDC link voltage Description 01.2004 Configuration Operation and control options Initial Start-Up Invertors after completing the basic Energizing the power and the unitPersons and equipment can occur by You are advised to only connect Transport Storage Unpacking Scope of delivery type G Transport, Storage, Unpacking Scope of delivery type J Box options Clearances InstallationInstalling the units Point of installation AFE basic mains module with CleanPower filter Mounting dimensions and dimension sheets Current Voltage Mounting dimensions of AFE reactor Partitions AFE inverter construction type GDoor/roof openings An arcing short-circuit must be prevented by the provision Opening cross sections Technical filter data in accordance with DIN FiltersFollowing filter mat is approved for use Fibroidelastov made by DELBAG-Luftfilter Gmbh Roof section Water coolingBuilt-in components Masterdrives VC inverters AFE inverter construction type JAppendix 01.2004 Installation Filters Mlfb Fan, flow rate, opening cross- sections Supply ImplementationDC auxiliary Slot 2 can be used for technology boards T100, T300, TSY Installing the optional boardsOpened until at least after this delay time Boards may only be replaced by qualified personnel Installation 01.2004 Installation in Conformance with EMC Regulations Connecting-Up and Wiring AFE reactor connection AFE basic mains module and CleanPower filterX3 connector terminal Connection overviews + D/L U2/T1 V2/T2 W2/T3Fan Fan connection 230 V 1 AC Electronics box for boards Cusa X9 connectorDC connection 210 a 3NE1 227-0 250 a 3NA3 144 250 a Mains Example configuration -7 for construction type J shows aControl transformer must be protected by a 6 a fuse Directly from the plant Typical circuit for AFE chassis unit, construction type J AFE inverter and AFE reactor Power connections Fan supply Auxiliary power supply, prechargingProtective conductor connection X9 external DC 24 V supply, precharging contactor control Control terminal Connectors forControl terminals Standard connections of the AFE inverter View of Cusa Terminal strip Connecting up control cablesTerminal assignments X100 control Terminal Name Function Range X101 control Possible cross- .5 mm 2 AWG X102 control Pin Name Function Range X300 serial interface Digital outputs Factory settingDigital inputs/outputs Connection Dual-port Ram DPR for SCB, TSY, CB, TB Only one of the above possible connections may be used View of option board VSB Voltage Sensing Board VSB VSB Connector assignments Please check Basic Function CheckCommissioning of the equipment P052 = Reset is run P052 automatically returns to Checking actual value acquisition and precharging P561 = Explanation of Terminology and Functionality of the AFE Data sets 10-1 Function Diagrams 10-2 Switchover, basic/reserve setting Basic/ResvSwitchover of reserve data set RDS 11-1 ParameterizationExamples Key Meaning Function Setting parameters via the PMU Key Toggle key Example Input rated supply voltage Input line frequency in Hz Menu selection Closed-loop control settingsStart-up parameterization Select language Function selection P052 Factory setting P052 = 1 Parameter reset To change P070 Access level Expert ModeInitialization Mlfb input P052 = Function Condition Result Select Download Download P052 =Select Return P051 = P090 = P091 = Hardware configuration P052 =TB installed in the electronics box of the converter 007, Starting Lockout 008 or Ready for on 009 states Select Closed-loop control settings Closed-loop control settings P052 = 12-1 Parameter ListKey to parameter list R006 DC Bus Volts General visualization parametersR001 Operating status R004 Output Amps R032 Line frequency 12-3R013 Operat. hours R030 Line volts P052 Function Select P051 Access LevelGeneral parameters P054 OP Backlight 12-5 Drive data R089 Board Position 12-7R082 Line filter L/% P083 Precharging P091 Board Position Hardware configuration Closed-loop control R152 Active RDS 12-10R139 R150 Control status P161 Startgen,max P164 Operating mode12-11 P160 Startmot,max 12-12 P308 Sampling Time P325 MC switch-on delP329 MCInvEnableDel 12-13 P409 Line contac. del FunctionsP387 P408 Forming time Setpoint channel P518 Deviation Time 12-16 Control and status bit connections 12-18 P576 Src. ext V ok P575 Src No Ext Fault112-19 P572 P588 Src No Ext Warn1 P586 Src No ExtFault212-20 P587 Src.slave AFE 12-21 12-22 12-23 P631 Dst Pre-Charging 12-24P629 DstPrechrgContEn P657 Cusa AnalogOutOffs P660 SCI AnalogInConfAnalog inputs/outputs P656 Cusa AnalogOutGain P665 SCI AnaOut Gain P662 SCI AnalogInOffs12-26 P664 SCI AnaOutActVal P684 SCom/SCB Baud Interface configurationP682 SCB Protocol P683 SCom/SCB BusAddr P689 SCB Peer2PeerExt 12-28P686 SCom/SCB # PrDat P687 SCom/SCB TlgOFF P695 CB/TB TlgOFFTime 12-29P694 CB/TB Act Values 12-30 R723 PCB Code Diagnostic functionsR721 SW Generat.Date R722 R730 SCB Diagnosis 12-32 R748 Trip Time 12-33 Factory parameters P799 Special AccessGating unit P928 Src Base/Reserve P927 Parameter AccessProfile parameters 12-36 R949 Fault ValueR951 Fault Texts 12-37 12-38 12-39 12-40 Application Control and Status WordsControl word Introduction Control word Display of control word on PMU seven-segment displayMultiple connections are permitted Bit No. meaning Factory setting applies only when P077 =Control word 1 visualization parameter r550 or r967 Designation Parameter No Control word 2 visualization parameter r551 Table X external terminals Sources for control words 1 Table D Table aTable B Table C Table H Table ETable F Table G 13-8 0000 0001 2004 3004 4501 4502 4503 4504 4505 Description of the control word bits Bit 0 on / OFF1 command ↑ on / L OFF1 ConditionBit 1 OFF2 command L OFF2 electrical Condition Bit 10 Control via PLC command H Control via PLC Condition Bit 7 Acknowledge command ↑ Acknowledge ConditionBit 8 Inching 1 on command ↑ Inching 1 on / L Inching 1 OFF Bit 9 Inching 2 on command ↑ Inching 2 on / L Inching 2 OFF Bit 19 Reserved Bit 20 Reserved Master AFE Bit 28 External alarm 1 command L External alarm ConditionBit 29 External alarm 2 command L External alarm Condition 13-13 High signalSetpoint channel and closed-loop control are activated Bit 31 Reserved PMU display Status word Status wordStatus word 1 visualization parameter r552 or r968 Destination Destination 13-15Bit # = High Select = Low Destin Bit Ready for on P600.x Status word 2 visualization parameter r553 = 1 0000 1001 1002 1003 13-17= High Select = Low Destin = 3 Description of the status word bits Bit 0 Ready for on signal H High signalBit 1 Ready to Run signal H High signal Bit 2 Run signal H High signal Bit 8 Setpoint/actual value deviation signal L LOW signal Bit 6 Starting lockout signal H High signalBit 7 Alarm signal H High signal Bit 22 AFE i2t alarm signal H High signal Meaning Bit 19 External fault 1 signal H High signalBit 20 External fault 2 signal H High signal Bit 21 External alarm signal H High signal Bit 23 AFE overtemperature fault signal H High signal F003 Line overvoltage Faults and AlarmsFaults Compare with P071 Line voltage 14-2 14-3 14-4 14-5 Alarms 14-7 Fatal errors FF Personnel MaintenanceSimovert Masterdrives units are operated at high voltages National electrical codes VBG 4 in Germany Position Equipment designation Brief description CleanPower filterElectrical components AFE basic mains module Replacing the fan AFE inverter maintenanceReplacement Fan assembly weighs about 30 kg Replacing the starting capacitor Replacing the fan fuses construction type J only Capacitor battery weighs up to 30 kg Replacing the capacitor battery PMU with adapter section on the electronics box Replacing the PMU 15.3.2 DC fuses FusesFan fuses for AFE inverters Number is made up FormingHow the serial Example A-J60147512345 End Switch on AFEP408 P052 = Key 17-1 Technical DataCleanPower filter AFE basic mains module 17-2 AFE basic mains module and CleanPower filter 17-3 6SE703x-xES87-1FG1 AFE reactor for construction type GAFE reactor for construction type J 17-4 17-5 AFE inverter Derating curves Designation Value 17-7 Environmental Friendliness Order No 6SE70 Certificates ConfirmationEquipment Type AC drive converter Equipment Type Order No 19-3 Type 6SE70 Chassis units AC-AC and DC-AC Operating manual ContentsAppendix Appendix toPage Page Page SIMOVERT-MASTERDRIVES AFE Siemens AG FKBL1-VSB1 Siemens AG Edition Internal Item Number A5E00243916Chapter Changes Pages Version date